Panasonic Projector PT-DX610UL User Manual

							ENGLISH - 91
Chapter 4 Settings  —   [SECURITY] menu
3) Press as to select [CONTROL PANEL] or 
[REMOTE CONTROL].
4) Press the  button.
rfThe  [CONTROL PANEL] screen or the [REMOTE CONTROL] 
screen is displayed.
5) Press as to select an item, and press the 
 button.
6) When the confirmation is displayed, select [OK] 
or [CANCEL], and press the  button.
r
r [CONTROL PANEL] and [REMOTE CONTROL]
rf Y ou can set the limitation on the control from the control panel and 
remote control.
[ENABLE] Enables all button operations on the projector body and remote control.
[DISABLE] Disables all button operations on the projector body and remote control.\
Note
rfWhen a button operation is performed on the device set to [DISABLE], the 
[SECURITY  PASSWORD] screen is displayed.
Enter the security password.
rf The 

[SECURITY PASSWORD] screen will disappear when the  button is pressed, or when there is no operation for approximately 
ten seconds.
rf If the operations of both [CONTROL

 PANEL] and [REMOTE CONTROL] are set to [DISABLE], the projector cannot be turned off (cannot 
enter standby).
rf When the setting has completed, the menu screen will disappear

. To operate continuously, press the  button to display the main 
menu.  
						

							92 - ENGLISH
Chapter 4 Settings  —   [NETWORK] menu
[NETWORK] menu
Select [NETWORK] from the main menu, and select the item from the sub-me\
nu.
Refer to “Navigating through the menu” (
x
 

page   51) for the operation of the menu screen.
rfAfter selecting the item, press 
asqw to set.
[NETWORK SETUP]
Perform the initial setting of the network before using the network function.
1) Press as to select [NETWORK SETUP].
2) Press the  button.
rfThe  [NETWORK SETUP] screen is displayed.
3) Press as to select an item, and change 
the settings according to the operation 
instructions of the menu.
4) Press as to select [STORE], and press the 
 button.
5) When the confirmation is displayed, select [OK] 
or [CANCEL], and press the  button.
r
r [NETWORK SETUP]
[PROJECTOR NAME]
Change the setting when using a DHCP server.
[DHCP] Set the item to [ON] when using a DHCP server to automatically acquire the IP address. Set to [OFF] when 
not using a DHCP server.
[IP ADDRESS] Enter the IP address when not using a DHCP server.
[SUBNET MASK] Enter the subnet mask when not using a DHCP server.
[DEFAULT GATEWAY] Enter the default gateway address when not using a DHCP server.
[STORE] Save the current network settings.
Note
rfWhen using a DHCP  server, confirm that the DHCP server is running.
rfConsult your network administrator regarding the IP

 address, subnet mask, and default gateway.
[NETWORK CONTROL]
Set up the control method of the network.
1) Press as to select [NETWORK CONTROL].
2) Press the  button.
rfThe  [NETWORK CONTROL] screen is displayed.
3) Press as to select an item, then press qw to 
change the setting.
4) Press as to select [STORE], and press the 
 button.
5) When the confirmation is displayed, select [OK] 
or [CANCEL], and press the  button.  
						

							ENGLISH - 93
Chapter 4 Settings  —   [NETWORK] menu
r
r [NETWORK CONTROL]
[WEB CONTROL]
Set to [ON] to control with the Web browser.
[PJLink CONTROL] Set to [ON] to control with the PJLink protocol.
[COMMAND CONTROL] Set to [ON] to control with the / terminal control command format 
(
x
 

page   123).
Refer to “Control commands via LAN” ( x
 

page   119).
[COMMAND PORT] Set the port number used for command control.
[CRESTRON RoomView] Set to [ON] to control with RoomView of Crestron.
[AMX D.D.] Set to [ON] to control with the controller of AMX.
[STORE] Save the current network control settings.
[NETWORK STATUS]
Displays the status of the projector network.
1) Press as to select [NETWORK STATUS].2) Press the  button.
rfThe  [NETWORK STATUS] screen is displayed.
Network connections
The projector has a network function, and the following operations are available from the computer using the W
eb control.
rfSetting and adjustment of the projector
rfDisplay of the projector status
rfSending of E-mail messages when there is a problem with the projector
“Crestron RoomV

iew” is a system of Crestron Electronics, Inc. that manages and controls devices on multiple systems connected to a network 
collectively with a computer.
The projector supports the following application software of Crestron Electronics, Inc.
g  RoomView Express
g  Fusion RV
g  RoomView Server Edition
rf For details of “Crestron RoomV

iew”, refer to the website of Crestron Electronics, Inc. (English only)
URL http://www.crestron.com
For the download of “RoomView Express”, also refer to the website of Crestron Electronics, Inc. (English only)
URL http://www.crestron.com/getroomview
Attention
rf Connect the LAN to indoor devices.
Note
rfA  LAN cable is required to use the network function.
&RPSXWHU
3URMHFWRU
/$1FDEOHVWUDLJKW /$1FDEOHVWUDLJKW +XE
rfA  Web browser is required to use this function. Confirm that the Web browser can be used beforehand.
Compatible OS: Windows XP/Windows Vista/Windows 7, Mac OS X v10.4/v10.5/v10.6/v10.7
Compatible browser: Internet Explorer 7.0/8.0/9.0, Safari 4.0/5.0 (Mac OS)
rf Communication with an E-mail server is required to use the E-mail function. Confirm that the E-mail can be used beforehand.
rfUse a LAN cable that is straight-through and compatible with category 5 or higher
.
rfUse a LAN cable of 100 m (328'1") or shorter length.  
						

							94 - ENGLISH
Chapter 4 Settings  —   [NETWORK] menu
Name and function of network function parts
1 2 3
1 LAN10/100 lamp (yellow)
Lights on when connected to the 100BASE-TX.
2
 
 terminal (
 10BASE-T/100BASE-TX)
Used to connect the LAN cable here. 3
 LAN LINK/ACT lamp (green)
Lights on when connected.
Flashes when transmitting/receiving data.
Accessing from the Web browser
1) Start up the Web browser on the computer.
2) Enter the IP address set on the projector into 
the URL entry field of the Web browser.
3) Enter the user name and the password.
rfThe factory default setting of the user name is user1 (user 
rights)/admin1 (administrator rights) and the password is 
panasonic (lower case).
4) Click OK.
rfThe [Projector status] page is displayed.
Note
rfIf you use a W eb browser to control the projector, set [WEB CONTROL] to [ON] in [NETWORK CONTROL] (
x  page   92).
rfDo not perform setting or control simultaneously by starting up multiple W
eb browsers. Do not set or control the projector from multiple 
computers.
rf Change the password first. (
x 

page   104)
rfThe administrator rights allows to use all functions. 

The user rights allow use of [Projector status] (x
 

page   95), confirmation of the error 
information page ( x
 

page   96), [Network status] (x
 

page   97), [Basic control] (x
 

page   98), and [Change password] (x
 

page   104) 
only.
rf Access will be locked for few minutes when an incorrect password is entered three times consecutively
.  
						

							ENGLISH - 95
Chapter 4 Settings  —   [NETWORK] menu
Descriptions of items
(1)
(2)
(3)
(4)
(5)
(6)
1 Page tab
Switches pages by clicking it.
2
 
[Status]
The status of the projector is displayed by clicking this item.
3

 
[Projector control]
The [Projector control] page is displayed by clicking this item. 4

 [Detailed set up]
The [Detailed set up] page is displayed by clicking this item.
5
 
[Change password]
The [Change password] page is displayed by clicking this item.
6

 
[CRESTRON RoomV
 iew]
The control page of RoomView is displayed by clicking this item.
[Projector status] page
Click [Status]  → [Projector status].
Displays the status of the projector for the following items.
(10)
(11)
(12)
(15)
(16) (6)
(7)
(8)
(9)
(1)
(2)
(3)
(4)
(13)
(14)
(5)
(17)
1 [PROJECT
OR TYPE]
Displays the type of the projector.
2
 
[MAIN VERSION]
Displays the firmware version of the projector

.
3
 
[POWER]
Displays the status of the power

.
4
 
[SHUTTER]
Displays the status of the projector

.
5
 
[LAMP
  SELECT]
Displays the setting status of [LAMP SELECT] ( x
 

page   76).
6
 
[SERIAL
  NUMBER]
Displays the serial number of the projector.
7
 
[NETWORK VERSION]
Displays the version of the firmware of the network.
8

 
[REMOTE2 ST
 ATUS]
Displays the control status of the  terminal.
9
 
[OSD]
Displays the status of the on-screen display

.
10
 
[LAMP
  POWER]
Displays the setting status of [LAMP POWER] ( x
 

page   77).
11
 [INPUT]
Displays the status of the input selection. 12

 [INT AKE AIR TEMPERATURE]
Displays the status of the air intake temperature of the projector.
13
 
[OPTICS MODULE TEMPERA
 TURE]
Displays the status of the internal temperature of the projector.
14
 
[AROUND LAMP
  TEMPERATURE]
Displays the status of the temperature around the lamp of the 
projector.
15
 
[LAMP1][LAMP2][RUNTIME]
Displays 

the status and the cumulative operating time (converted 
value) of the lamp.
16
 
[SELF TEST]
Displays the self-diagnosis information.
17

 
[PROJECT
 OR RUNTIME]
Displays the operation times of the projector.  
						

							96 - ENGLISH
Chapter 4 Settings  —   [NETWORK] menu
Error information page
When [Error (Detail)] is displayed in the self-diagnosis display of the [Projector status] screen, click it to display the error details.
rfThe projector may go into the standby status to protect the projector de\
pending on the contents of the error

.
>2.@RSHUDWLQJSURSHUO\
>)$,/(@DSUREOHPRFFXUUHG>:$51,1*@ZDUQLQJ
r
r Problem occurrence [FAILED]
Parameter
Description
[MAIN CPU BUS] There is a problem with the microcomputer circuitry. Consult your dealer.
[FAN] There is a problem with the fan or the fan drive circuit. Consult your dealer .
[INTAKE AIR TEMPERATURE] The air intake temperature is too high. It may be used in an operating environment where 
the temperature is high, such as near a heating appliance.
[OPTICS MODULE TEMPERATURE] The temperature inside the projector is high. It may be used in an operating environment 
where the temperature is high, such as near a heating appliance.
[AROUND LAMP TEMPERATURE] The temperature around the lamp is high. The air exhaust port may be blocked.
[LAMP1 REMAIN TIME] The usage time of the lamp has exceeded the specified time, and it is time to replace the 
lamp.
[LAMP2 REMAIN TIME]
[LAMP1 STATUS] The lamp has failed to turn on. Wait a while until the luminous lamp cools off, and then 
turn on the power.
[LAMP2 STATUS]
[SHUTTER] There is a problem with the shutter circuitry. Consult your dealer.
[INTAKE AIR TEMP.SENSOR] There is a problem with the sensor used to detect intake air temperature. Consult your 
dealer.
[OPTICS MODULE TEMP.SENSOR] There is a problem with the sensor used to detect temperature inside the projector
. 
Consult your dealer.
[AROUND LAMP TEMP.SENSOR] There is a problem with the sensor used to detect exhaust air temperature. Consult your 
dealer.
[BATTERY] Battery replacement is required. Consult your dealer.
[COLOR WHEEL] There is a problem with the color wheel or the color wheel drive circuit. Consult your 
dealer.
[COVER OPEN] The lamp unit cover is not attached properly. Check the installation of the lamp unit 
cover. (
x
 

page   114)
[FILTER UNIT] The air filter unit is not attached. Check the connection of the air filter unit. (
x
 

page   113)
[AIR FILTER] There are too much dust accumulated in the air filter unit.
Turn the  switch  (
x
 

page   43), and clean the air filter. 
( x
 

page   112)  
						

							ENGLISH - 97
Chapter 4 Settings  —   [NETWORK] menu
[Network status] page
Click [Status]
 → [Network status].
The current network setting status is displayed.
[Access error log] page
Click [Status]  → [Access error log].
The error log on the WEB server is displayed such as access to the pages that do not exist or access with unauthorized user names or 
passwords.
[Access log] page
Click [Status]  → [Access log].
The log such as user name accessed to the WEB control page, accessed IP  address, and accessed time is displayed.
Note
rf[Access error log]/[Access log] will display the recent few thousand accesses/requests. May be unable to display all information when many 
accesses/requests are made at one time.
rfWhen [Access error log]/[Access log] exceeds a certain amount, old information will be erased.
rfConfirm [Access error log]/[Access log] periodically

.  
						

							98 - ENGLISH
Chapter 4 Settings  —   [NETWORK] menu
[Basic control] page
Click [Projector control]
 → [Basic control].
(1)
(2)
(4)
(6) (3)
(5)
1 [POWER]
Switches the power on/of
f.
2
 
[SHUTTER]
Switches between use or not use of the shutter function.
3

 
[OSD]
Switches between on (display)/of

f (no display) of the on-screen 
display function. 4
 [SYSTEM]
Switches the system method.
5
 
On-screen display of the projector
Displays the same content as the on-screen display of the 
projector

. The settings of the menu can be checked or changed. 
This is displayed even when the on-screen display function is 
set to off (hide).
6
 
[INPUT SELECT]
Switches the input signal.
[Detail control] page
Click [Projector control] → [Detail control].
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(1)
1 Control of the projector
The projector is controlled by clicking the buttons in the same 
way as the buttons on the remote control. 
After the projector is 
controlled, the on-screen display of the projector on the right 
side of the control page is updated.
2
 
[LENS]
Adjusts the projection lens.
3

 
[TEST P
 ATTERN]
Displays the test pattern. 4
 [GET OSD]
Updates the on-screen display of the projector at the right of the 
control page.
5
 
[SUB MEMOR
 Y]
Switches the sub memory.
6
 
[SYSTEM DA
 YLIGHT VIEW]
Switches to system daylight view settings.
7
 
[FREEZE]
T

emporarily pauses the image.
8
 
[SIDE BY
  SIDE] (only for PT-DW640U)
Displays two different input signals simultaneously.
[Network config] page
Click [Detailed set up]  → [Network config].
rfClick [Network config] to display the [CAUTION!] screen.
rfThe current settings are displayed by pressing the [Next] button.  
						

							ENGLISH - 99
Chapter 4 Settings  —   [NETWORK] menu
rfThe following setting change screen is displayed by pressing the [Change] button.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
1 [PROJECT
OR NAME]
Enter the name of the projector. Also enter the host name if it is 
required when using a DHCP server, etc.
2
 
[DHCP
  ON]/[DHCP OFF]
To enable the DHCP client function, set to [DHCP ON].
3
 
[IP
  ADDRESS]
Enter the IP address when not using a DHCP server.
4
 
[SUBNET MASK]
Enter the subnet mask when not using a DHCP

 server.
5
 
[DEF
 AULT GATEWAY]
Enter the default gateway address when not using a DHCP 
server. 6
 [DNS1]
Enter the DNS1 server address.
Permissible characters for the entry of DNS1 server address 
(primary):
Numbers (0 to 9), period (.)
(Example: 192.168.0.253)
7
 
[DNS2]
Enter the DNS2 server address.
Permissible characters for the entry of DNS2 server address 
(secondary):
Numbers (0 to 9), period (.)
(Example: 192.168.0.254)
8

 
[Back]/[Next]
Click the [Back] button to return to the original screen. 

The 
current settings are displayed by pressing the [Next] button. 
Click the [Submit] button to update the settings.
Note
rf When you use the “Forward” and “Back” functions of your browser , a warning message “Page has Expired” may appear. In that case, click 
[Network config] again since the following operation will not be guaranteed.
[Adjust clock] page
Click [Detailed set up]  → [Adjust clock].
(1)
(2)
(3)
(4)(5)(6)
(7)
1 [Time Zone]
Select the time zone.
2
 
[Set time zone]
Updates the time zone setting.
3

 
[NTP
  SYNCHRONIZATION]
Set to [ON] to adjust the date and time automatically.
4
 
[NTP
  SERVER NAME]
Enter the IP address or server name of the NTP server when 
you set to adjust the date and time manually.
(To enter the server name, the setup of the DNS server is 
required.) 5
 [Date]
Enter the date to be changed.
6
 
[T
 ime]
Enter the time to be changed.
7
 
[Set date and time]
Updates the date and time settings.  
						

							100 - ENGLISH
Chapter 4 Settings  —   [NETWORK] menu
Note
rfThe replacement of the battery inside the projector is required when the time goes out of alignment right after correcting the time. Please 
consult your dealer
.
[Ping test] page
You can check whether the network is connected to the E-mail server, POP server, DNS server, etc.
Click [Detailed set up]  → [Ping test].
(1)
(2)
(3)
(4)
1 [Input IP  address]
Enter the IP address of the server to be tested.
2
 
[Submit]
Executes the connection test. 3

 Example of display when the connection has succeeded
4  
Example of display when the connection has failed