Panasonic Projector Pt Dw7000e Operating Instructions

							91
ENGLISH
POP server setup page
The POP server is set on this page when POP authentication is required for mail transmissions.
Click [Network set up], then [POP server set up] to display the POP server setup page.
Select “Enable” for this setting
only when authentication is
required for sending mail.
POP server name field
Available input characters: 
Alphanumeric characters (A–Z,
a–z, 0–9), hyphen (-), period (.)
POP server user name field
Button to update settings
POP server password field
Ping test page
This page makes it possible to check whether the network is connected to the E-mail server, POP server, DNS
server, etc.
Click [Network set up], then [Ping test] to display the Ping test page.
Enter the IP address of the
server to be tested.
Button for conducting the
test.
Display which appears when
the connection was
successful.
Display which appears when
the connection failed.     
						

							92
Subject: Panasonic projector report(CONFIGURE)
=== Panasonic projector report(CONFIGURE) ===
Projector Type          : D7700
–––––E-mail setup data –––––
TEMPERATURE WARNING SETUP 
MINIMUM TIME           at [ 60] minutes interval 
INPUT AIR TEMPERATURE  Over [ 35C / 95F ] 
ERROR [ ON ] 
LAMP1 RUNTIME [ OFF ] at REMAIN  [200]  H 
LAMP1 RUNTIME [ OFF ] at REMAIN  [100]  H 
LAMP2 RUNTIME [ OFF ] at REMAIN  [200]  H 
LAMP2 RUNTIME [ OFF ] at REMAIN  [100]  H 
INPUT AIR TEMPERATURE [ OFF ] 
PERIODIC REPORT 
Sunday [ OFF ] Monday [ OFF ] Tuesday [ OFF ] Wednesday [ ON  ] 
Thursday [ OFF ] Friday [ OFF ] Saturday [ OFF ] 
00:00 [ OFF ] 01:00 [ OFF ] 02:00 [ OFF ] 03:00 [ OFF ] 
04:00 [ OFF ] 05:00 [ OFF ] 06:00 [ OFF ] 07:00 [ OFF ] 
08:00 [ OFF ] 09:00 [ OFF ] 10:00 [ OFF ] 11:00 [ OFF ] 
12:00 [ OFF ] 13:00 [ OFF ] 14:00 [ OFF ] 15:00 [ OFF ] 
16:00 [ OFF ] 17:00 [ OFF ] 18:00 [ ON ] 19:00 [ OFF ] 
20:00 [ OFF ] 21:00 [ OFF ] 22:00 [ OFF ] 23:00 [ OFF ] 
–––––check system –––––
MAIN CPU BUS [   OK   ]
FAN  [   OK   ]
OPTICS MODULE TEMPERATURE [   OK   ]
INPUT AIR TEMPERATURE [   OK   ]
OUTPUT AIR TEMPERATURE [   OK   ]
LAMP2 REMAIN TIME [   OK   ]
LAMP1 REMAIN TIME [   OK   ]
•
•
•
Contents of mail sent
• Mail with the contents shown below is sent when the E-mail settings have been established.
Subject: Panasonic projector report(ERROR)
=== Panasonic projector report(ERROR) ===
Projector Type          : D7700
–––––check system –––––
MAIN CPU BUS [ OK ]
FAN [ OK ]
OPTICS MODULE TEMPERATURE [ OK ]
INPUT AIR TEMPERATURE [ OK ]
OUTPUT AIR TEMPERATURE [ OK ]
LAMP2 REMAIN TIME [ OK ]
LAMP1 REMAIN TIME [ OK ]
LAMP2 STATUS [ OK ]
LAMP1 STATUS [ FAILED ]
OPTICS MODULE TEMP.SENSOR [ OK ]
INPUT AIR TEMP.SENSOR [ OK ]
OUTPUT AIR TEMP.SENSOR [ OK ]
BATTERY [ OK ]
(Error code 00 40 00 00)
Input air temperature : 27 degC / 80 degF
Output air temperature : 65 degC /149 degF
SET RUNTIME 1857 H
POWER ON 248 times
LAMP1 ON 177 times
LAMP1 LOW 0 H
LAMP1 HIGH 68 H
LAMP2 ON 183 times
LAMP2 LOW 0 H
LAMP2 HIGH 75 H
LAMP1 REMAIN 1432 H
LAMP2 REMAIN 1425 H
–––––Network configuration –––––
IP address 192.168.0.8
MAC address 00:00:00:00:00:00
Wed Jan 26 18:54:31 2005
–––––Memo –––––
• Mail with the contents shown below is sent when an error has occurred.
How to use network function (optional) 
						

							93
ENGLISH
Adjust clock page
Click [Network set up], then [Adjust clock] to display the Adjust clock page.
Time zone selection
Button to update time zone
setting
Button to update time and
date settings 
New date field
New time field
Network config page
Set this to ON to enable the
DHCP client function.
Enter the IP address if DHCP
server is not used.
Enter the net mask if DHCP
server is not used.
Enter the port number here.
Number 80 is normally used.
Enter the gateway address if
DHCP server is not used.
Enter the name of the projector here. Enter the host name
here if it is required when the DHCP server is going to be
used, for instance. • If the time becomes incorrect immediately after setting the correct time, then the battery needs to be
changed. Contact the dealer where you bought the projector to have the battery changed.
Note   
						

							94
Firmware update page
(The firmware should be updated only by an individual with the specialized knowledge required to do this.)
Enter here the filename of the
firmware to be updated.
After entering the filename,
press the [Upload] button. Data
transfer is now commenced.
It will take several dozen
seconds for the data to be
transferred.
The time taken will differ
depending on the network
conditions.
Displays the current version.
Displays the updated version.
Check the updated version
against the current version,
and if everything is in order,
press the [Write] button.
Version data rewriting is now
commenced.
Do not turn off the power while
the version data is being
rewritten.
• Messages such as the ones shown below appear during data rewriting.
• The following message appears upon completion of the version data rewriting.
How to use network function (optional)       
						

							95
ENGLISH
Press the “ENTER” button.
The OPTION screen will be displayed.
Select “NETWORK SETTING” with the
buttons.
Returning the network function setting back to the
factory setting
Using the following procedure, the user can return all settings of network function such as IP address,
password and Email setting to the factory setting.
Procedure of setting
Press the “MENU” button.
The MAIN MENU screen will be displayed.
Select “OPTION” with the 
buttons.
Press the “ENTER” button.
The NETWORK SETTING screen will be
displayed.
Select “STORE” with the  
buttons.
Hold down the “Standard (STD)” button
for 3 seconds.
A confirmation screen will be displayed.
To cancel, press the “MENU” button. The
NETWORK SETTING screen will be displayed.
Press the “ENTER” button.
The IP address, password, E-mail settings and all
the other network function settings are returned to
the factory defaults.
OPTION
  PROJECTOR ID 2
  SETTING FRONT-F
  LAMP SELECT DUAL
  LAMP POWER HIGH
  RS232C SETTING
  OSD POSITION 2
  SYSTEM INFORMATION
  COLOR MATCHING 3COLORS
  VIDEO SETTING
  NETWORK SETTING
     :MENU SELECT
ENTER:SUB MENU
MAIN MENU
         PICTURE
         POSITION
         ADVANCED MENU
         LANGUAGE
         OPTION
         TEST PATTERN
         SIGNAL LIST
         SECURITY
     :MENU SELECT
ENTER:SUB MENU
NETWORK SETTING
  HOST NAME PROJECTOR
  DHCP OFF
  IP ADDRESS 192.168.    0.    8
  PORT       80
  NET MASK 255.255.255.    0
  GATEWAY 192.168.    0.    1
  MAC ADDRESS 00.00.00.00.00.00
  STORE
     :MENU SELECT    
ENTER:ADJUST
WOULD YOU LIKE TO CANCEL
ALL NETWORK SETTINGS BACK TO
FACTORY SHIPMENT STATUS?
OK ESC
      :CHANGE    ENTER:SET 
						

							96
Indication of monitor lamp
Three monitor lamps are provided at the top of main unit front to inform the user of the lamp replacement time and
unusual internal temperature.  These lamps indicate the degree of abnormality by combination of blinking and/or
lighting lamps.  Turn off the power and take the proper measure according to the table below.
Lamp 2 monitor (LAMP2)
Lamp 1 monitor (LAMP1)
Temperature monitor (TEMP)
TEMP LAMP1 LAMP2POWER
• Be sure to observe the procedure (How to turn “ON” and “OFF” the power supply) on page 33–34
when performing power supply operation to take a measure to the indication of temperature
monitor (TEMP) lamp and lamp monitor (LAMP) lamp.Attention
Name of monitor
lampLamp
indicationInformation
Warm-up status 
High temperature
inside. (WARNING)• Check if the
ventilation port is
blocked.
• Is the room air
temperature too high?
• Check the air filter for
clogging.
Checkpoint
• Remove the object that is
blocking the ventilation port.
• Move the projector to a
temperature of 0 to 40 ˚C and
the humidity of 20 to 80% (no
condensation).
• Turn off the MAIN POWER
switch using the procedure on
page 34 and clean the air filter
(refer to page 97).
• Did you turn on the
power when the
ambient temperature
was low (approx. 0
°C)? • Wait about five minutes in the
current status.
• Install the unit in a location
having an ambient
temperature from 0 to 40 °C. 
Lighting in
red
(lamp unit
ON)
Remedial measure
Blinking in
red
(2 times)High temperature
inside
(Standby condition)
Blinking in
red
(3 times)Cooling fan has
been stopped.
• Turn off the main power supply
(MAIN POWER) switch in the
procedure shown on page 34
and consult the distributor.
• This lamp monitor lights up
when the lamp unit used hours
have reached 1 300 hours 
(3 800 hours when Long Life
Lamp Units are used).
Request the dealer to replace
the lamp unit.
• Turn off the MAIN POWER
switch using the procedure on
page 34 and consult the
dealer.
• Did you notice a
“REPLACE THE
LAMP” message on
the screen when
turning on the
projector power
supply?
• Some error has
arisen in the lamp
circuit.
• Check for fluctuation
(or drop) in the source
voltage.
Indicates the time
for replacing the
lamp unit.
Error is detected in
the lamp circuit.
Lighting in
red
Blinking in
red
(3 times)
Temperature 
monitor
TEMP
Lamp monitor
LAMP1       LAMP2
• Wait until the lamp has cooled
off, and then turn on the
power.• Did you turn the
power back on
immediately after
turning it off? 
						

							97
Cleaning and replacement of air filter
ENGLISH
Turn off the main power and remove the power plug from the receptacle.
Turn off the main power supply observing the procedure (How to turn “OFF” the power supply) on page 34
and then remove the power plug.
Dismantle the air filter.
Put a hand in the bottom of the air filter, 
take out the filter from the main unit while pulling toward
yourself.
Clean the air filter.
Suck off deposited dust with a vacuum cleaner.
Mount the air filter.
Set the air filter and then mount the filter in the reverse order to step .
Air filter
• Do not to suck in the air filter itself.
• The air filter must be fitted in place when using the projector.
Using the projector without the air filter fitted inside, dirt and dust are sucked into the projector,
causing failure.
Attention
Attention
• If cleaning cannot remove the dust completely, then it is a sign to replace the air filter.  Consult the
dealer. In addition, when the lamp unit is replaced, also replace the air filter.
Note If too much dust is deposited in the air filter, temperature inside the main unit will rise and the temperature monitor
(TEMP) lamp blinks, eventually turning off the power supply.
Clean the air filter section once every 100 hours or so as a guideline depending on the location of projector
operation.
Procedure of cleaning 
						

							98
Replacement of lamp unit 
Precautions on lamp unit replacement
Be careful when handling a light source lamp.
The lamp unit has high internal pressure. If
improperly handled, failure might result.
A used lamp unit may burst if it is handled
violently.
For disposition of used lamps, request an
industrial waste disposal contractor.
Do not reset the cumulative time, except when
the lamp unit has been replaced with a new
unit.
If you continue to use a lamp after the
replacement time, the lamp may break.
Philips screwdriver is necessary when replacing
a lamp unit.
Take care not to slip your hand when using a
screwdriver.
• A lamp unit is an optional part.  Contact
the dealer.
Replacement Lamp Unit model No.: 
ET-LAD7700 (single bulb), 
ET-LAD7700W (double bulbs)
Rating: 300W
Long Life Lamp Unit model No.: 
ET-LAD7700L (single bulb), 
ET-LAD7700LW (double bulbs)
Rating: 160W 
• Other lamps than specified above cannot
be used.  Be sure to use the specified
lamp.AttentionThe lamp used for the light source has its due life.  The
life of light source lamp used in the main unit is 1 500
hours
1(when lamp output is HIGH and lamp
selection is DUAL). However, it may happen that the
lamp becomes dead (will not light) by the time of 1 500
hours
1depending on the characteristics of individual
lamps and working conditions (lamps may reduce their
life affected by the times of lighting and the intervals
between previous lighting and next lighting). Therefore,
it is strongly recommended for the user to keep a
spare bulb.
If your lamp unit is not replaced after 1 300 hours
2
(with the lamp output set at “HIGH”), power supply will
be turned off automatically at the time of 1 500 hours1,
entering a standby state.  After 1 500 hours1of initial
lighting, power supply is turned off automatically about
10 minutes later, entering a standby state even if it is
turned on again.
Indication after 1 300 hours2
(with the lamp output set at
HIGH)
When lamp unit used hours have reached 1 300
hours2, lamp monitor (LAMP1 or LAMP2) light
up including standby state.
Further, an on-screen indication will appear for
about 30 seconds as shown in the diagram on the
right, recommending replacement of lamp unit.
(The indication on the below diagram will
disappear after about 30 seconds or when either
control button on the rear of main unit or remote
control button is operated.)
After the time of 1 500 hours
1, the on-screen
indication will not disappear unless the menu
(MENU) button is operated.
REPLACE THE LAMP
CAUTION
Wait until the lamp is cooled sufficiently before replacing the lamp unit.
Timing of lamp unit
replacement
1 This time period is 4 000 hours when Long
Life Lamp Units are used.
2 This time period is 3 800 hours when Long
Life Lamp Units are used. 
						

							99
ENGLISH
• After 1 500 hours (4 000 hours when Long Life Lamp Units are used) of operating the same lamp, it is
only possible to operate the unit for approximately 10 minutes. Steps 9 to 15 must be completed within
ten minutes.
1. Turn the power off by following the steps on pages 33 - 34, remove the power plug
and confirm that the surroundings of the lamp unit have cooled off.
2. Using a Philips screwdriver, remove
the 7 screws on the lamp unit cover
located on the rear of the projector.
3. Remove the lamp unit cover from the
main unit.
4. Use a Phillips screwdriver to loosen
each of the two lamp unit fixing screws
until the screws turn freely. Then hold
the handle of the lamp unit and gently
pull it out from the projector.
Caution
The lamp unit will be hot after it has
been used.
You might get burned if you  touch it while it is still
hot.
5. Install the new lamp unit.
6. Use a Phillips screwdriver to securely tighten the two lamp unit fixing screws for
each lamp unit.
7. Install the lamp unit cover, and then
use a Phillips screwdriver to securely
tighten the lamp unit cover fixing 7
screws.
• Firmly install the lamp unit and lamp
unit cover. If not installed firmly, a
protection circuit will function and the
power will not be turned on.
Procedure of lamp unit replacement
Lamp unit coverFixing screws
Lamp unit
Fixing screwsHandle
Lamp unit
Fixing screws
Lamp unit 2Lamp unit 1
Lamp unit coverFixing screws
Caution
Caution 
						

							100
8. Insert the power cord plug into the wall outlet and then press the MAIN POWER
switch.
• If the power does not turn on (power indicator lamp (red) does not turn on) even after turning the
MAIN POWER switch “I”, turn the MAIN POWER “
O”, confirm that the lamp unit and door are
installed correctly, and turn on again.
9. Press the “I” (POWER) button so that a picture is projected onto the screen.
10. Press the “MENU” button to display
the MAIN MENU screen, and then
press the  and  buttons to move
the cursor to select “OPTION”.
13. Press and hold the “ENTER” button
on the projector or the remote control
for approximately 3 seconds.
An item “LAMP RESET” will be added.
14. Select the lamp which has been
replaced with the  and  buttons.  
LAMP1: Replace the LAMP UNIT 1
LAMP2: Replace the LAMP UNIT 2
11. Press the “ENTER” button to display
the “OPTION” screen, and select
“SYSTEM INFORMATION” with the 
and buttons.
12. Press the “ENTER” button.
The SYSTEM INFORMATION screen will be
displayed.
15. Press the “ENTER” button. When
“OK?” is displayed, press the
“ENTER” button.
The used hours of the specified lamp unit will be
reset to zero.
When more than one lamp has been replaced,
repeat the procedure from step 14.
MAIN MENU
         PICTURE
         POSITION
         ADVANCED MENU
         LANGUAGE
         OPTION
         TEST PATTERN
         SIGNAL LIST
         SECURITY
LAMP RESET
  LAMP1
   LAD7700 1433h
   LAD7700L 0h
  LAMP2
   LAD7700 1100h
   LAD7700L 0h
  
  
  
  
     :SELECT   
 ENTER:EXECUTE
OPTION
  PROJECTOR ID 2
  SETTING FRONT-F
  LAMP SELECT DUAL
  LAMP POWER HIGH
  RS232C SETTING
  OSD POSITION 2
  SYSTEM INFORMATION
  COLOR MATCHING 3COLORS
  VIDEO SETTING
  AUTO SETUP
     :MENU SELECT
ENTER:SUB MENU
SYSTEM INFORMATION
  ROM VERSION: 1.00  
  SET RUNTIME: 1433h
  LAMP1 TYPE: LAD7700
                   LOW: 0h
                  HIGH: 1433h
    TOTAL: 1433h
  LAMP2    TYPE: LAD7700
                   LOW: 0h
                 HIGH: 1100h
     TOTAL: 1100h
LAMP RESET OK?
  LAMP1
   LAD7700 1433h
   LAD7700L 0h
  LAMP2
   LAD7700 1100h
   LAD7700L 0h
  
  
Caution
Replacement of lamp unit