Panasonic Projector Pt Dw6300u Operating Instructions

							Replacement
ENGLISH - 31
Maintenance
JReplacement procedure
QRemoving and replacing the lamp unit
1. Use a Phillips-head screwdriver to loosen the 1 
lamp unit cover fixing screw on the back of the 
projector until the screws turn freely, and remove 
the lamp unit cover.
 Slide the lamp unit cover to the buttons and pull to 
remove.
2. Use a Phillips-head screwdriver to remove the 
3 lamp unit fixing screws.
3. Hold the handles of the lamp unit and pull the used 
lamp unit gently from the projector.4. Hold the handle of the new lamp unit and replace it 
in correct direction.
5. Press in the lamp unit until it clicks and make sure 
the unit is installed securely.
6. Tighten the 3 lamp unit fixing screws securely with 
a Phillips-head screwdriver.
7. Attach the lamp unit cover and tighten the 1 lamp 
unit cover fixing screw securely with a Phillips-
head screwdriver.
 Slide the lamp unit cover to the hinge side and push 
in to attach securely.
 Make sure the fan electric power connector of the 
lamp unit cover is inserted securely to the projector’s 
connector.
JBefore replacing the ACF
 Wait until the cooling fan stops and turn off the POWER switch of the projector in proper way.
 Disconnect the power cord from the wall outlet.
 Contact an Authorized Service Center to purchase a replacement ACF (ET-ACF100).
JWhen to replace the ACF
The ACF unit is consumable product and effects on ventilation. The FILTER indicator will inform you of the 
replacement timing. You can check the remaining amount of the ACF unit in REMAINING FILTER of STATUS 
in PROJECTOR SETUP menu.
Lamp unit cover 
fixing screw
Lamp unit cover
Handle
Handle Lamp unit screws Lamp unit screws
Fan electric power 
connector
Replacing the Auto Cleaning Filter (ACF) 
						

							Maintenance
Replacement
ENGLISH - 32
JReplacement procedure
1. Loosen 1 ACF cover fixing screw until the screws 
turn freely and remove the ACF cover.
2. Slide out the ACF unit from the projector slowly.
 When you replace the ACF unit, clean the 
compartment and/or the air exhaust port if you need 
to.
3. Insert the new ACF unit into the compartment in 
correct direction and slightly push until it clicks.
4. Attach the ACF cover and tighten 1 ACF cover 
fixing screw securely.
JResetting the REMAINING 
FILTER
1. Turn on the projector and display the FILTER 
COUNTER RESET in PROJECTOR SETUP 
menu.
2. Press the ENTER button.
 The confirmation screen will be displayed.
3. Select OK by pressing I, then press the ENTER 
button.
4. Display the STATUS in PROJECTOR SETUP 
menu and confirm the REMAINING FILTER.
NOTE:
• If the ACF and/or ACF cover are attached incorrectly, the 
projector may not be turned on.
• Do not switch the power on while the ACF cover removed.
• The replacement timing of the ACF is 36 000 hours of use at 
maximum and it depends on environment of usage.
ACF cover fixing screw
ACF cover
ACF unit
NOTE:
• See FILTER COUNTER RESET and STATUS in 
PROJECTOR SETUP menu of the functional instructions that 
is in the provided CD-ROM. 
						

							ENGLISH - 33
Maintenance
Troubleshooting
Should any problem persist, contact your dealer.
ProblemCauseReference 
page*1
*1. CD-ROM: See the functional instructions in the provided CD-ROM.
Power does not turn on.
 The power cord may not be connected.
 The POWER switch is turned off.
 No electric supply is at the wall outlet.
 TEMP indicator is lit or flashes.
 LAMP1/LAMP2 indicator is lit or flashes.
 The lamp unit cover has not been securely installed.
 The circuit breakers have tripped.18
20
20
28
28
31
-
No picture appears.
 The video signal input source may not be connected to a terminal 
properly.
 The input selection setting may not be correct.
 The BRIGHTNESS adjustment setting may be at the minimum setting.
 The input source which is connected to the projector may have a 
problem.
 The shutter function may be in use.CD-ROM
22
CD-ROM
22
The picture is fuzzy.
 The lens focus may not have been set correctly.
 The projector may not be at the correct distance from the screen.
 The lens may be dirty.
 The projector may be tilted too much.19
CD-ROM
-
CD-ROM
The color is pale or grayish.
 COLOR or TINT adjustment may be incorrect.
 The input source which is connected to the projector may not be 
adjusted correctly.
 RGB cable is damaged.CD-ROM
-
-
The control buttons of the 
projector do not operate.
 CONTROL PANEL of CONTROL DEVICE SETUP in SECURITY 
menu is disabled. If you have a loss of the remote control while the 
CONTROL PANEL is disabled, press and hold the MENU button for 
2 seconds with pressing the ENTER button.CD-ROM
The remote control does 
not operate.
 REMOTE CONTROLLER of CONTROL DEVICE SETUP in 
SECURITY menu is disabled.
 The batteries may be weak.
 The batteries may not have been inserted correctly.
 The remote control signal receptor on the projector may be 
obstructed.
 The remote control unit may be out of the operation range.
 Strong light such as fluorescent shine onto the signal receptor.
 The remote control ID setting is incorrect.CD-ROM
-
14
21
21
-
CD-ROM
The picture does not 
display correctly. The color format may not have been set correctly.
 There may be a problem with the VCR or other signal source.
 A signal which is not compatible with the projector is being input.CD-ROM
-
34
Picture from a computer 
does not appear.
 The cable may be longer than the optional cable.
 The external video output from a laptop computer may not be correct. 
(You may be able to change the external output settings by pressing 
the [Fn] + [F3] or [Fn] + [F10] keys simultaneously. The actual method 
varies depending on the type of computer; refer to the documentation 
provided with your computer for further details.)-
-
Picture from a computer 
DVI-D graphic board does 
not appear.
 The graphic board driver of the computer needs to be updated to the 
latest version.
 DVI-D IN setting in DISPLAY OPTION menu may be incorrect setting.
 The computer may need to be restarted after switching DVI-D IN 
setting in DISPLAY OPTION menu of the projector correctly.-
CD-ROM
- 
						

							ENGLISH - 34
Appendix
Technical Information
List of compatible signals
Mode
Display 
resolution 
(dots)
*1
Scanning 
frequencyDot clock 
frequency
Picture 
quality*2
PnP*3
Format*4
H (kHz)V (Hz)(MHz)RGB2DVI-D 
EIDI1DVI-D 
EIDI2
NTSC/NTSC 4.43/
PAL-M/PAL60720 x 480i 15.7 59.9 - A
V/S
PAL/PAL-N/SECAM 720 x 576i 15.6 50.0 - A
525i (480i) 720 x 480i 15.7 59.9 13.5 A
R/Y
625i (576i) 720 x 576i 15.6 50.0 13.5 A
525p (480p) 720 x 483 31.5 59.9 27.0 AD
D/R/Y 625p (576p) 720 x 576 31.3 50.0 27.0 AD
1 125 (1 080)/60i
1 920 x 1 080i33.8 60.0 74.3
AA
*5D
1 125 (1 080)/50i 28.1 50.0 74.3
AA
*5D
1 125 (1 080)/24p 1 920 x 1 080 27.0 24.0 74.3
AA
*5D
1 125 (1 080)/24sF 1 920 x 1 080i 27.0 24.0 74.3
AA
*5
1 125 (1 080)/25p
1 920 x 1 08028.1 25.0 74.3
AA*5D
1 125 (1 080)/30p 33.8 30.0 74.3
AA
*5
1 125 (1 080)/60p
 1 920 x 1 080p67.5 60.0 148.5
AA*5D
1 125 (1 080)/50p 56.3 50.0 148.5
AA
*5D
750 (720)/60p
1 280 x 72045.0 60.0 74.3
AA
*6D
750 (720)/50p 37.5 50.0 74.3
AA
*6D
VGA400 640 x 40031.5 70.1 25.2 A
D/R 37.9 85.1 31.5 A
VGA480 640 x 48031.5 59.9 25.2 ADD D
35.0 66.7 30.2 A
37.9 72.8 31.5 ADD
37.5 75.0 31.5 ADD
43.3 85.0 36.0 A
SVGA 800 x 60035.2 56.3 36.0 ADD
37.9 60.3 40.0 ADD
48.1 72.2 50.0 ADD
46.9 75.0 56.3 ADD
53.7 85.1 56.3 A
MAC16 832 x 624 49.7 74.6 57.3 ADD
XGA 1 024 x 76839.6 50.0 51.9
AA
*7
48.4 60.0 65.0
AA*7DD
56.5 70.1 75.0
AA
*7DD
60.0 75.0 78.8
AA
*7DD
65.5 81.6 86.0
AA
*7
68.7 85.0 94.5
AA*7
80.0 100.0 105.0
AA*7
96.7 120.0 130.0
AA*7
MXGA 1 152 x 86464.0 71.2 94.2 A
67.5 74.9 108.0 A
76.7 85.0 121.5 A
MAC21 1 152 x 870 68.7 75.1 100.0 ADD
1 280 x 768 1 280 x 96039.6 49.9 65.3
AA
*6
47.8 59.9 79.5
AA*6
1 280 x 800 1 280 x 80041.3 50.0 68.0
AA*6
49.7 59.8 83.5
AA*6
MSXGA 1 280 x 960 60.0 60.0 108.0 A
SXGA 1 280 x 1 02464.0 60.0 108.0 ADD
80.0 75.0 135.0 ADD
91.1 85.0 157.5
A
*8D/R*9
SXGA+ 1 400 x 1 05065.2 60.0 122.6 ADDD/R
82.2 75.0 155.9
A*8D/R*9
WXGA+ 1 440 x 900 55.9 59.9 106.5 A D/R
UXGA 1 600 x 1 200 75.0 60.0 162.0
A*8D
DD/R*9 
						

							Technical Information
ENGLISH - 35
Appendix
JDisplay dots of each model
WSXGA+ 1 680 x 1 050 65.3 60.0 146.3 A
D/R 1 920 x 1 080*101 920 x 1 080 66.6 59.9 138.5
AA*5
WUXGA 1 920 x 1 200 74.0 60.0 154.0
AA*5DD
*1. The “i” appearing after the resolution indicates an interlaced signal.
*2. The following symbols are used to indicate picture quality.
AA Maximum picture quality can be obtained.
A Signals are converted by the image processing circuit before picture is projected.
B Some loss of data occurs to make projection easier.
*3. Marked signals are indicated in 
*4. The following symbols are used to indicate the format.
V = VIDEO, S = S-VIDEO, D = DVI, R = RGB, Y = YP
BPR*5. PT-DW6300U/PT-D6000U: A
*6. PT-DZ6710U/PT-DZ6700U/PT-D6000U: A
*7. PT-DZ6710U/PT-DZ6700U/PT-DW6300U: A
*8. PT-DW6300U/PT-D6000U: B
*9. RGB signals only and DVI-D is not compatible.
*10.VESA CVT-RB (Reduced Blanking) compatible.
NOTE:
• Projecting an interlaced signal may cause flicker in screen.
PT-DZ6710U1 920 x 1 200
PT-DZ6700U1 920 x 1 200
PT-DW6300U1 280 x 800
PT-D6000U1 024 x 768
Mode
Display 
resolution 
(dots)
*1
Scanning 
frequencyDot clock 
frequency
Picture 
quality*2
PnP*3
Format*4
H (kHz)V (Hz)(MHz)RGB2DVI-D 
EIDI1DVI-D 
EIDI2 
						

							Appendix
Technical Information
ENGLISH - 36
Specifications
Power supplyAC 120 V 60 Hz
Power consumption• PT-DZ6710U/PT-DZ6700U: 820 W
• PT-DW6300U/PT-D6000U: 780 W
During standby (when fan is stopped): Approx. 8 W*1
Amps• PT-DZ6710U/PT-DZ6700U: 8 A
• PT-DW6300U/PT-D6000U: 7.2 A
DLP™ chip
Panel size 
(diagonal)• PT-DZ6710U/PT-DZ6700U: 0.67 type • PT-DW6300U: 0.65 type
• PT-D6000U: 0.7 type
Aspect ratio• PT-DZ6710U/PT-DZ6700U/PT-DW6300U: 16 : 10
• PT-D6000U: 4:3
Display method
1 unit DLP™ chip, DLP™ type
Pixels• PT-DZ6710U/PT-DZ6700U: 2 304 000 (1 920 x 1200)
• PT-DW6300U: 1 024 000 (1 280 x 800)
• PT-D6000U: 786 432 (1 024 x 768)
Lens
Motorized zoom1.8 - 2.4:1• Lens is optional for the projectors that “L” 
follows in model number.
Motorized focus• F 1.7 - 2.0, f 25.6 mm - 33.8 mm
• PT-DZ6710U/PT-DZ6700U: f = 26.8 - 35.7
• PT-DW6300U/PT-D6000U: f = 25.6 - 33.8
LampUHM lamp (300 W) x 2
Luminosity*2
• PT-DZ6710U/PT-DZ6700U/
PT-DW6300U:6 000 lm (ANSI)
• PT-D6000U: 6 500 lm (ANSI)• Lens is optional for the projectors that “L” 
follows in model number.
Average value of the lens that is provided with the 
projector.
Operating environmentTemperature: 0 °C - 45 °C (32 °F - 113 °F)
Humidity: 20% - 80% (no condensation)
Scanning 
frequency*3
VIDEO/S-VIDEOH: 15.75 kHz/15.63 kHz, V: 50 Hz/60 Hz
RGBH: 15 - 91 kHz, V: 50 - 85 Hz Panasonic Intelligent Auto Scanning (PIAS)
Dot clock frequency
• PT-DZ6710U/PT-DZ6700U: 162 MHz or less
• PT-DW6300U/PT-D6000U: 150 MHz or less
DVI-D480p, 576p, 720/60p, 720/59.94p, 720/50p, 1 080/60p, 1 080/59.94p,1 080/50p, 1 080/60i,  
1 080/59.94i, 1 080/50i, 1 080/24sF, 1 080/23.98sF, 1 080/30p, 1 080/29.97p, 1 080/25p,  
1 080/24p, 1 080/23.98p
Displayable resolution: VGA - WUXGA (non interlace)
Dot clock frequency: 25 - 162 MHz
WUXGA signal is applicable with VESA CVT-RB (Reduced Blanking).
YPBPR
• 480i H: 15.73 kHz, V: 59.94 Hz
• 480p H: 31.5 kHz, V: 59.94 Hz
• 720/50p H: 37.5 kHz, V: 50 Hz
• 1 035/60i H: 33.75 kHz, V: 60 Hz
• 1 080/60i H: 33.75 kHz, V: 60 Hz
• 1 080/25p H: 28.13 kHz, V: 25 Hz
• 1 080/24sF H: 27 kHz, V: 48 Hz
• 1 080/60p H: 67.5 kHz, V: 60 Hz• 576i H: 15.63 kHz, V: 50 Hz
• 576p H: 31.25 kHz, V: 50 Hz
• 720/60p H: 45 kHz, V: 60 Hz
• 1 080/50i H: 28.13 kHz, V: 50 Hz
• 1 080/24p H: 27 kHz, V: 24 Hz
• 1 080/30p H: 33.75 kHz, V: 30 Hz
• 1 080/50p H: 56.25 kHz, V: 50 Hz
HD/SYNC, VD terminals are not compliant with 3 value composite SYNC.
Color system7 (NTSC/NTSC 4.43/PAL/PAL-M/PAL-N/PAL60/SECAM)
Projection size50 - 600 (1 270 mm - 12 700 mm)
Screen aspect ratio• PT-DZ6710U/PT-DZ6700U/PT-DW6300U: 16 : 10
• PT-D6000U: 4:3
InstallationFRONT/FLOOR, FRONT/CEILING, REAR/FLOOR, REAR/CEILING
(Menu selection method)
Contrast ratio2 000 : 1 (When CONTRAST MODE in DISPLAY OPTION menu is set to HIGH) 
						

							Technical Information
ENGLISH - 37
Appendix
Te r m i n a l s
S-VIDEO IN1 set, Mini DIN 4p 
Y: 1.0 V [p-p], C: 0.286 V [p-p], 75 Ω, compatible with S1 signal
VIDEO IN1 set, BNC pin jack 
1.0 V [p-p], 75 Ω
RGB 1 IN1 set, BNC x 5
 RGB signal 
0.7 V [p-p], 75 
Ω
• G-SYNC: 1.0 V [p-p], 75 Ω
• HD/SYNC: TTL high impedance, automatic positive/negative polarity compatible
• VD: TTL high impedance, automatic positive/negative polarity compatible
 YP
BPR signal
• Y: 1.0 V [p-p] Synchronisation signal included
•P
BPR: 0.7 V [p-p], 75 Ω
RGB 2 IN1 set of high density, D-sub 15p (female)
 RGB signal 
0.7 V [p-p], 75 
Ω (G-SYNC: 1.0 V [p-p], 75 Ω)
• HD/SYNC: TTL high impedance, automatic positive/negative polarity compatible
• VD: TTL high impedance, automatic positive/negative polarity compatible
 YP
BPR signal
• Y: 1.0 V [p-p] Synchronisation signal included
•P
BPR: 0.7 V [p-p], 75 Ω
DVI-D IN1 set, DVI-D 24-pin (Single link), DVI 1.0 compatible, HDCP compatible
SERIAL1 set, D-sub 9-pin (female), RS-232C compatible, computer control use
REMOTE11 set, M3 pin jack, wired remote control use, multiple connection use
REMOTE21 set, D-sub 9-pin, external control use
LAN1 set, RJ-45, network connection use, PJLink™ compatible,  
10 Base-T/100Base-TX
SDI1 set, BNC pin jack
SD-SDI (Y, CB, CR, 4:2:2)
• SMPTE259M: 480i, 576i• SMPTE292M: 720/50p, 720/60p, 1 035/60i, 
1 080/50i, 1 080/60i, 1 080/25p, 1 080/24p, 
1 080/24sF, 1 080/30p
CabinetMoulded plastic
Power cord length3.0 m (910)
DimensionsWidth 498 mm (19- 19/32)
Height 175 mm (6 - 7/8)
Length 448 mm (17 - 5/8)
Weight
Approx. 16 kg (35.3 lbs.)*4
Remote 
control
Power supply3 V DC (AA battery x 2)
Operating rangeApprox. 30 m (985) (when operated directly in front of signal receptor)
Weight120 g (4.2 ozs.) (including batteries)
DimensionsWidth 51 mm (2)
Length 176 mm (6 - 29/32)
Height22.7 mm (-7/8) (not including surface projection 
parts)
Options
Ceiling bracketET-PKD56H (High ceiling), ET-PKD55S (Low ceiling)
Projection lensET-DLE150, ET-DLE250, ET-DLE350, ET-DLE450, ET-DLE055
Lamp unitET-LAD60 (1 bulb), ET-LAD60W (2 bulbs)
ACF unitET-ACF100
*1. When STANDBY MODE in PROJECTOR SETUP menu is NORMAL: Approx. 8 W 
When STANDBY MODE in PROJECTOR SETUP menu is ECO: Approx. 0.2 W
*2. Measurement, measuring conditions and method of notation all comply with ISO21118 international standards.
*3. See “List of compatible signals” on page 34 for available signals.
*4. Average value. Each product has an individual variable in weight. 
						

							Appendix
Technical Information
ENGLISH - 38
 VGA and XGA are trademarks of International Business Machines Corporation.
 S-VGA is a registered trademark of the Video Electronics Standards Association.
 The font used in the on-screen displays is a Ricoh bitmap font, which is manufactured and sold by Ricoh 
Company, Ltd. 
All other trademarks are the property of the various trademark owners.
Dimensions
Trademark acknowledgements
423
(16-5/8) 5
(-3/16)
498
(19-19/32)
155
(6-3/32) 77.5
(3-1/32) 20
(-25/32)
21
(-13/16)16.8
(-21/32)9
(-11/32)
Unit: mm (inch) 
						

							ENGLISH - 39
Appendix
Index
A
Accessories .................................................................... 11
Air exhaust port
 ............................................................... 12
Air intake port
 .................................................................. 13
ASPECT
Remote control button ................................................. 14
Remote control function ............................................... 22
Auto Cleaning Filter (ACF)
 .............................................. 13
AUTO SETUP
Control panel button .................................................... 12
Remote control button ................................................. 14Remote control function ............................................... 21
B
Battery ............................................................................ 11
Compartment .............................................................. 14
Burglar hook port
 ............................................................ 12
C
CD-ROM ......................................................................... 11
Accessories ................................................................ 11
Menu ......................................................................... 24
D
DEFAULT
Remote control button ................................................. 14
Remote control function ............................................... 23
Dimensions
 ..................................................................... 38
Direct power off
 ............................................................... 20
DISPLAY LANGUAGE
 .................................................... 24
DVI-D
Control panel button .................................................... 12
Remote control button ................................................. 14Terminal .................................................................... 13
E
ENTER
Control panel button .................................................... 12
Menu navigation ......................................................... 27
Remote control button ................................................. 14
F
FILTER
Compartment .............................................................. 13
Indicator ..................................................................... 12
Indicator status ........................................................... 29Replacing ................................................................... 31
FOCUS
Adjusting .................................................................... 19
Remote control button ................................................. 14
Focus ring
 ....................................................................... 12
Front leg adjusters
 .......................................................... 12
FUNCTION
Remote control button ................................................. 14Remote control function ............................................... 23
I
ID
Remote control button ................................................. 14
Setting ....................................................................... 15
INPUT SELECT
Control panel button .................................................... 12Remote control buttons ................................................ 14
Remote control function ............................................... 22
INSTALLATION
Projection method ....................................................... 16
L
LAMP
Indicator status ........................................................... 28
Lamp unit compartment ............................................... 12LAMP1/LAMP2 indicators ............................................ 12
Replacing .................................................................. 30
LAN
Terminal .................................................................... 13
LENS
Control panel button .................................................... 12
Projection lens ............................................................ 12Projector lens cover .................................................... 11
Remote control button ................................................. 14
Lens home position
 ........................................................ 20
M
Mains lead
AC IN terminal ............................................................ 13
Accessories ............................................................... 11Connecting ................................................................ 18
MENU
CD-ROM ................................................................... 24
Control panel button .................................................... 12
Navigation ................................................................. 27Remote control button ................................................. 14
Structure .................................................................... 24
N
Navigation buttons
Control panel .............................................................. 12Navigation ................................................................. 27
Remote control buttons ............................................... 14
Numeric (0 - 9) buttons
Remote control buttons ............................................... 14
O
ON SCREEN
Remote control button ................................................. 14
Remote control function ............................................... 22
P
POWER
Switch ....................................................................... 13
Switching on/off .......................................................... 19
Power cord secure lock
Accessories ............................................................... 11
Attaching ................................................................... 18
POWER ON
Control panel button .................................................... 12Remote control button ................................................. 14
Switching on/off .......................................................... 19
POWER STANDBY
Control panel button .................................................... 12
Remote control button ................................................. 14
Projector lens cover
Accessories ............................................................... 11
R
Remote control ............................................................... 14
Accessories ............................................................... 11
Signal receptor ........................................................... 12
Wired connection ........................................................ 15
REMOTE1
Terminal .................................................................... 13Wired connection ........................................................ 15
REMOTE2
Terminal .................................................................... 13 
						

							Appendix
Index
ENGLISH - 40
RGB1
Control panel button .................................................... 12Remote control button ................................................. 14
Terminal .................................................................... 13
RGB2
Control panel button .................................................... 12
Remote control button ................................................. 14Terminal .................................................................... 13
S
Safety cable
Accessories ............................................................... 11
SDI
Control panel button .................................................... 12
Remote control button ................................................. 14Terminal .................................................................... 13
Security lock
 ................................................................... 13
SERIAL
Terminal .................................................................... 13
SHIFT
Adjusting ................................................................... 19Adjustment range ....................................................... 20
Remote control button ................................................. 14
SHUTTER
Control panel button .................................................... 12
Remote control button ................................................. 14Remote control function ............................................... 22
Specifications
 ................................................................. 36
STATUS
Remote control button ................................................. 14Remote control function ............................................... 23
S-VIDEO
Control panel button .................................................... 12
Remote control button ................................................. 14
Terminal .................................................................... 13
T
TEMP
Indicator .................................................................... 12Indicator status ........................................................... 28
TEST PATTERN
Remote control button ................................................. 14
Remote control function ............................................... 22
Troubleshooting
 .............................................................. 33
V
VIDEO
Control panel button .................................................... 12
Remote control button ................................................. 14Terminal .................................................................... 13
Z
ZOOM
Adjusting ................................................................... 19
Remote control button ................................................. 14