Panasonic Projector Pt D4000u Operating Instructions

11
AC IN terminal (page 22)
Connect the supplied line power cord into this
receptacle.
Do not connect any other cable to this socket.
Air filter (page 51)
Security lock
Attach a commercial burglar prevention cable (e.g.,
from Kensington) to this lock port. It is compatible
with the Microsaver Security System from
Kensington. 
Anti-theft hook
Attach a chain or other fastening device available
from a hardware store through this clamp.
Level-adjusting feet (page 22)
Use these feet to adjust the tilt of the...

12
Name and function of parts 
Lamp unit cover
The lamp unit is housed.
MAIN POWER switch (page 22)
Use this switch to turn on “I” and off “O” the main
power applied to the projector.
Remote control receiver window (rear) (page 14)
This also receives the signal beam coming from
the remote control.
POWER ON ( I ) button (page 22)
Turns on the power.
POWER STANDBY ( ) button (page 23)
Switches the power to the “standby” mode.
RGB1 button (page 22)
Switches to RGB1 input.
RGB2 button (page 22)
Switches to...

13
VIDEO IN terminal (page 21) 
An input terminal for video signals. (BNC)
S-VIDEO IN terminal (page 21)
An input terminal for S-Video signals. 
(MIN4-pin DIN)
This terminal complies with S1 signals and
automatically toggles between 16:9 and 4:3
according to the size of input signals.
RGB 1 input (RGB 1 IN) terminal (page 21)
A terminal to input RGB or YP
BPRsignals. (BNC)
RGB 2 input (RGB 2 IN) terminal (page 21)
A terminal to input RGB or YP
BPRsignals. (D-Sub
15-pin female)
DVI-D IN terminal (page...

14
Using the remote control unit
Loading dry cells
When loading batteries into the battery
compartment of the remote control, make sure that
their polarities are correct.
1. Open battery compartment lid.
Open the lid in the order of steps  and  .
2. Insert the dry cells.
Into battery compartment, with their polarities
orientated as indicated ( ,  ) in the
compartment.
3. Close the battery compartment lid.
Replace the battery compartment lid over the
compartment and slide until it clicks.
Effective range...

15
Setting projector ID number to remote control
Every projector has its ID number and the ID number of the controlling projector must be set to the remote
control in advance so that the user can operate the remote control. The ID number of the projector is set to
“ALL” on shipping, and use the ID ALL button of the remote control when using only a single projector.
Procedure of ID setting 
Press the ID SET button, and within five seconds use the number (0 to 9) buttons
to enter the 2-digit ID number set...

16
Installation
FRONT REAR
FLOOR
CEILING
(Default position)
Installation geometry
When planning the projector and screen geometry, refer to the figure below and the information on the next
page for reference. After the projector is roughly positioned, picture size and vertical picture positioning can be
finely adjusted with the powered zoom lens and lens tilt mechanism.
Side view
With optional ceiling mount
bracket (ET-PKD56H)
256
(10.1)
HH
ScreenSH185
(7.3)L
L
 417-497
(16.4-19.6)
Top view
200
(7.9) 100...

17
Projection distance by projection lens
Unit : m, ( ) : inch, [ ] : footScreen aspect ratio 4:3
1.27
(50)
1.52
(60)
1.78
(70)
2.03
(80)
2.29
(90)
2.54
(100)
3.05
(120)
3.81
(150)
5.08
(200)
6.35
(250)
7.62
(300)
8.89
(350)
10.16
(400)
12.70
(500)
15.24
(600)
Diagonal
length
(SD)
Height
(SH)
1.02
[3.33]
1.22
[4.00]
1.42
[4.67]
1.63
[5.33]
1.83
[6.00]
2.03
[6.66]
2.44
[8.00]
3.05
[10.00]
4.06
[13.33]
5.08
[16.66]
6.10
[19.99]
7.11
[23.33]
8.13
[26.66]
10.16
[33.32]
12.19
[39.99]
Width
(SW)Minimum
(LW)...

18
Installation
Unit : m, ( ) : inch, [ ] : footScreen aspect ratio 16:9
1.27
(50)
1.52
(60)
1.78
(70)
2.03
(80)
2.29
(90)
2.54
(100)
3.05
(120)
3.81
(150)
5.08
(200)
6.35
(250)
7.62
(300)
8.89
(350)
10.16
(400)
12.70
(500)
15.24
(600)
Diagonal
length
(SD)
Height
(SH)
1.11
[3.63]
1.33
[4.36]
1.55
[5.08]
1.77
[5.81]
1.99
[6.54]
2.21
[7.26]
2.66
[8.71]
3.32
[10.89]
4.43
[14.52]
5.53
[18.15]
6.64
[21.78]
7.75
[25.41]
8.86
[29.05]
11.07
[36.31]
13.28
[43.57]
Width
(SW)Minimum
(LW)
Maximum
(LT)
1.97 
[6.58]...

19
Note• The dimensions in the table in pages 17, 18 and the values obtained from the above formulas may
contain slight errors.
• When an SXGA signal is input and projected, the right and left ends of the picture will be blanked
and the aspect ratio will be 5:4.
• The brightness is different between the wide lens position settings and telephoto lens position
settings.
Standard 
zoom lens
Wide-angle fixed-
focus lens
Wide-angle
zoom lens
Intermediate-focus
zoom lens
Long-focus
zoom lens
Ultra-long-focus...

20
Connection
Setup precautions
• Before connecting any of your video/audio equipment to the projector, carefully read the owners manual
supplied with the equipment once again.
• All cable connections should be made with the entire system devices, including the projector, first turned off.
• Obtain commercial interconnecting cables for devices supplied with no accessory or optional interconnect
cables.
• Video signals containing too much jitter may cause the images on the screen to randomly wobble or...