Panasonic Projector Pt D12000 Specifications

							SPECFILE
PT-D120003-Chip DLP™ Projector
As of July 2008< 11 >
Status asking commands
Command : Parameter FunctionDescription Callback
QPW
QSH
QIN
QOS
QST
Q$L:p1
Q$L:p2
Q$L:p3
Q$L:p4
QSL
QIB
QPP
QGD
QGTMain power status
Shutter function status
Input signal status
On-screen display status
Projector run time
Lamp 1 run time
Lamp 2 run time
Lamp 3 run time
Lamp 4 run time
Lamp operation mode status
Optional board slot status
P in P status
Date setting status
Time setting statusOn
Off
On
Off
RGB 1
RGB 2
Video
S-Video
DVI
AUX
On
Off
00000h –99999h
0000h –9999h
0000h –9999h
0000h –9999h
0000h –9999h
Quad (four lamps)
Lamp 1 + 4
Lamp 2 + 3
Dual (two lamps)
Lamp 1 + 2 + 3
Lamp 1 + 2 + 4
Lamp 1 + 3 + 4
Lamp 2 + 3 + 4
Triple (three lamps)
Lamp 1
Lamp 2
Lamp 3
Lamp 4
Single lamp
ET-MD77SD1
ET-MD77SD3
ET-MD100SD4
ET-MD77DV
Uninstalled
Unknown
Not supported
Off
User 1
User 2
User 3
yyyymmdd (day of week) 
(*1) 
hhmmss (*2)  001
000
1
0
RG1
RG2
VID
SVD
DVI
AUX
1
0
00000-99999
0000-9999
0000-9999
0000-9999
0000-9999
0
1
2
3
4
5
6
7
8
9
10
11
12
13
MD77SD1
MD77SD3
MD100SD4
MD77DV
NONE
UNKNOWN
NOT SUPPORT
0
1
2
3
y1y2y3y4m1m2d1d2w
h1h2m1m2s1s2
*1
*2Day of week: Monday = 1, Tuesday = 2, ... Sunday = 7
Set the date and time to UTC (universal time coordinated).
Command example
To set the on-screen display off, send the command as shown below.
ADZZ OOS : 0; ETX
ID AddressZZ: ID ALLCommand
STX
StartCharacter code 02Parameter EndCharacter code 03
NOTE: When sending commands without parameters, a colon (:) is not necessary. NOTE: If a wrong command is received, the projector will send an ER401 or ER402 command to the computer. 
						

							SPECFILE
PT-D120003-Chip DLP™ Projector
As of July 2008< 12 >
The projector uses a high-wattage lamp that becomes very hot during operation.\
 Please observe the
following precautions.
1. Never place objects on top of the projector while it is operating.
2. Make sure there is an unobstructed space of 500 mm (19-11/16˝) or more around the projector’s
exhaust openings.
3. Do not stack projector units directly on top of one another for the purpose of multiple (stacked) projection. When stacking projector units, be sure to provide the amount of space indicated below
between them. These space requirements also apply to installations where only one projector unit
is operating at one time and the other unit is used as a backup.
4. If the projector is placed in a box or enclosure, ensure the temperature of the air surrounding the projector is between 0°C/32°F and 40°C/104°F. Also make sure the projector’s intake and exhaust
openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is
not sucked into the intake openings.
500 mm (19-11/16˝)  or more 500 mm
(19-11/16˝) or more* 500 mm
(19-11/16˝) or more*
Operating the Projector Continuously
1.  If the projector is to be operated continuously 24 hours, use the lamp relay mode. The projector cannot
be operated continuously 24 hours in quad-lamp mode. Allow a minimum of \
two hours per day of non-
operation time if the projector is to be operated continuously more than 22 hours.
2.  The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.
Weights and dimensions shown are approximate. Specifications are subject to change without notice. This product may be subject  to
export control regulations. DLP and the DLP logo are trademarks of Texas Instruments. UHM is a trademark of Matshushita Electic . 
The PJLink is an application trademark in Japan, the United States, and \
other countries and regions or registered trademarks. 
All other trademarks are the property of their respective trademark owners.
Intake
Exhaust
Direction of Air Intake and Exhaust Notes on Projector Placement and Operation
* When two units are used together.  300 mm (11-13/16˝) or more for a
single unit operation.
Do not stack projector
units directly on top
of one another.