Panasonic Projector PT-AE7000U User Manual

							[PICTURE] menu
ENGLISH - 41
Settings
[COLOR TEMPERATURE]
You can adjust the color temperature if the white 
areas of the projected image are bluish or reddish.Less bluish
Less reddish
Setting range: -6 to +6
 
z
[SHARPNESS]
With regards to the input signal, adjust video 
sharpness using one of [SIMPLE] which adjusts 
horizontal direction and vertical direction 
simultaneously or [ADVANCED] which adjusts each 
individually.
Softer
Sharper
Note
Setting range will vary according to the selected input 
 
z
signal.
[SHARPNESS] can be adjusted using either [SIMPLE] or 
 
z
[ADVANCED]. Both settings cannot be used at the same 
time.
Adjusting the [SHARPNESS].  
 
z
(When [SIMPLE] is selected for the 
[ADJUSTMENT MODE].)
Press 
1)  
▲
▼ buttons to select [SIMPLE].
 SHARPNESS
 A DJUSTMENT  MODE
 SHARPNESS
 H-SHARPNESS
 V -SHARPNESS SIMPLE
0
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
Select [SHARPNESS] with the ▲▼ 
2)  
buttons, and adjust with the 
▲
▼ buttons.
Adjusting the [SHARPNESS].  
 
z
(When [ADVANCED] is selected for the 
[ADJUSTMENT MODE].)
Press the ◄► buttons to select 
1)  
[ADVANCED].
 SHARPNESS
 ADJUSTMENT  MODE
 SHARPNESS
 H-SHARPNESS
 V -SHARPNESS  A
DV ANCED
0
0
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
Select item with the ▲▼ buttons, and 
2)  
adjust with the 
▲
▼ buttons.
Pressing the ▲▼ buttons on the screen during 
 
z
adjustment switches to the [H-SHARPNESS] or 
[V-SHARPNESS] adjustment screen.
 H-SHARPNESS
 V-SHARPNESS 0
0
The setting range varies according to the selected 
 
z
picture mode and input signal.
[DYNAMIC IRIS]
You can switch automatic adjustment of the lamp and 
the lens iris on/off. This augments the video to create 
a video expression with sharp contrast between light 
and shade.
Switch settingsSwitch settings
[ON] Automatic adjustment
[OFF] No adjustment
[WAVEFORM MONITOR]
By using a commercial test disk etc. and setting the 
luminance level of the output (brightness) signal from 
a connected external device to a value within this 
projector’s recommended range, you can perform 
adjustment so the display performance of the projector 
can be fully leveraged.
Press the  button.
1)  
The [WAVEFORM MONITOR] menu is displayed.
 
z
 W AV EFORM MONITO R
    OFF
    FULL  SCAN(Y)
    FULL  SCAN(R)
    FULL  SCAN(G)
    FULL  SCAN(B)
    SINGLE LINE SCAN(Y)
    SINGLE LINE SCAN(R)
    SINGLE LINE SCAN(G)
    SINGLE LINE SCAN(B)
 MONIT OR POSITION
 A UT O ADJUST UPPER LEFTÔ
Press the ▲▼ buttons to select the 
2)  
required item.
Select [OFF] to close the waveform monitor.
 
z
Press the  button.
3)  
The waveform monitor is displayed.
 
z
Note
For details, see “Displaying the waveform monitor” in 
 
z
“Remote control operation”. (
 page 33) 
						

							[PICTURE] menu
42 - ENGLISH
Settings
 
■ [MONITOR POSITION]
You can set the display position of the input waveform 
during the FULL SCAN display.
Switch settingsSwitch settings
[
 
■ AUTO ADJUST]
The luminance level of the output signal from a connected 
external device is automatically adjusted by setting the 
automatic waveform adjustment items.
Press the  button.
1)  
Press the ▲▼ buttons to select the 
2)  
required item.
Automatic waveform 
adjustment items Default 
setting
[BLACK LEVEL ADJUST] [ON]
[WHITE LEVEL ADJUST] [ON]
[RGB ADJUST (BLACK)] [OFF]
[RGB ADJUST (WHITE)] [OFF]
Press the ◄► buttons to switch 
3)  
adjustment.
Press the ▲▼ buttons to select [START 
4)  
AUTO ADJUST] and press the  
button.
[PROCESSING] message is displayed. When 
 
z
adjustment is complete, a confirmation message for 
applying results is displayed.
Select [OK] with the 
5)  ▲
▼ buttons.
Press the  button.
6)  
Note
When [BLACK LEVEL ADJUST] is [ON], the display 
 
z
signal Y (brightness) value’s black level is automatically 
adjusted to the 0% position.
When [WHITE LEVEL ADJUST] is [ON], the display 
 
z
signal Y (brightness) value’s white level is automatically 
adjusted to the 100% position.
When [RGB ADJUST (BLACK)] is [ON], the display signal 
 
z
R (Red), G (Green), and B (Blue) value’s black level are 
all automatically adjusted to the 0% position.
When [RGB ADJUST (WHITE)] is [ON], the display signal 
 
z
R (Red), G (Green), and B (Blue) value’s white level are 
all automatically adjusted to the 100% position.
[AUTO ADJUST] cannot be executed if the [WAVEFORM 
 
z
MONITOR] is [OFF].
Project the luminance adjustment signal of a commercial 
 
z
test disk etc., and perform automatic adjustment. 
However, even with an adjustment disk, correct 
adjustment may not be possible if noise is included on 
the disk itself or the playback device generates noise. [AUTO ADJUST] adjusts based on the 0% and 100% 
 
z
standard signal within the screen, so correct adjustment 
cannot be performed if standard signals are not displayed 
on the screen because of overscan etc., or if a signal that 
is less than 0% or greater than 100% is displayed on the 
screen.
When 3D is being displayed (including converting 2D to 
 
z
3D), the [WAVEFORM MONITOR] cannot be executed.
 
■ Adjust the waveform
Project the brightness adjustment signal of a commercial 
test disk (0% [0 IRE or 7.5 IRE] - 100% [100  IRE] ) and 
perform adjustment.
 
RETURN
MOVE DISPLA
Y
CHANGE WF MODE
Adjust to 100%
Signal (luminance) level
Signal (luminance) level
Monitor 
position
Monitor 
position Adjust to 100%
Adjust to 0 %
With COMPUTER (except 1 080 
signal) or HDMI (Expand)
Adjust to 0 % Image 
displayable 
area
Image 
displayable 
area
With the [WAVEFORM MONITOR] displayed, press the 
 button on the remote control and adjust using 
[ADVANCED MENU] and [PICTURE] from the on-screen 
menu. 
						

							[PICTURE] menu
ENGLISH - 43
Settings
Adjust [FULL SCAN(Y)] / [SINGLE LINE 
1)  
SCAN(Y)].
Set on [PICTURE] and use the 
 
z▲
▼ buttons to 
adjust [BRIGHTNESS] and then [CONTRAST].
[BRIGHTNESS]
Adjust the bottom line of the 
waveform to 0 %  
(0 or 7.5 IRE)
Setting range:  
 
z
−32 to +32
[CONTRAST]
Adjust the top line of the 
waveform to 100 %  
(100 IRE)
Setting range:  
 
z
−64 to +64
Adjust [FULL SCAN(R)] / [SINGLE LINE 
2)  
SCAN(R)].
Set on [ADVANCED MENU] and use the 
 
z▲
▼ 
buttons to adjust [BRIGHTNESS R] and then 
[CONTRAST R].
[BRIGHTNESS R]
Adjust the bottom line of the 
waveform to 0 %  
(0 or 7.5 IRE)
Setting range:  
 
z
−16 to +16
[CONTRAST R]
Adjust the top line of the 
waveform to 100 %  
(100 IRE)
Setting range:  
 
z
−32 to +32
Adjust [FULL SCAN(G)] / [SINGLE LINE 
3)  
SCAN(G)].
Set on [ADVANCED MENU] and use the 
 
z▲
▼ 
buttons to adjust [BRIGHTNESS G] and then 
[CONTRAST G].
[BRIGHTNESS G]
Adjust the bottom line of the 
waveform to 0 %  
(0 or 7.5 IRE)
Setting range:  
 
z
−16 to +16
[CONTRAST G]
Adjust the top line of the 
waveform to 100 %  
(100 IRE)
Setting range:  
 
z
−32 to +32
Adjust [FULL SCAN(B)] / [SINGLE LINE 
4)  
SCAN(B)].
Set on [ADVANCED MENU] and use the 
 
z▲
▼ 
buttons to adjust [BRIGHTNESS B] and then 
[CONTRAST B].
[BRIGHTNESS B]
Adjust the bottom line of the 
waveform to 0 %  
(0 or 7.5 IRE)
Setting range:  
 
z
−16 to +16
[CONTRAST B]
Adjust the top line of the 
waveform to 100 %  
(100 IRE)
Setting range:  
 
z
−32 to +32
Note
When a 3D signal is being input (including converting 
 
z
2D to 3D), the [WAVEFORM MONITOR] cannot be 
executed. 
						

							[PICTURE] menu
44 - ENGLISH
Settings
[SPLIT ADJUST]
You can perform image adjustment for some 
[PICTURE] menu items while displaying a certain 
area of the frozen image in a split window.
Press the  button.
1)  
The [SPLIT ADJUST] menu is displayed.
 
z
SPLIT  ADJUST
AREA  SELECT
SPLIT  ADJUST  MODE
NORMAL
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
Press the ▲▼ buttons to select [AREA 
2)  
SELECT] and then press the  
button.
The image is frozen and an area for adjustment is 
 
z
displayed. The image being projected is recorded 
and displayed as a frozen image.
Use the 
3)  ▲
▼ buttons to select the area to 
be adjusted.
MOVE  AREA     ENTER : GO T O SPLIT ADJUST      RETURN : GO T O FREEZE SCREEN
Note
Press the  button, and a frozen screen is 
 
z
displayed.
Press the  button.
4)  
Split screen display begins.
 
z
 
MENU : GO T O PICTURE MENU     ENTER :  ADJUSTMENT COMPLETE     RETURN : GO TO  AREA  SELECT
MENU : GO T O PICTURE MENU     ENTER :  ADJUSTMENT COMPLETE     RETURN : GO TO  AREA  SELECT
[When [SPLIT ADJUST MODE] is [NORMAL]]
[When [SPLIT ADJUST MODE] is [REVERSE]]
Note
By selecting the [SPLIT ADJUST MODE] with the ▲▼ 
 
z
buttons and switching [NORMAL] to [REVERSE], the 
screen displayed on the left during split screen display 
can be reversed and adjusted.
Press the  button and make 
5)  
adjustments with the [PICTURE] menu.
The menu screen is displayed. You can adjust the 
 
z
image for optimal display.
PICTURE MODE
CONTRAST
BRIGHTNESS
COLOR
TINT
COLOR  TEMPERAT URE
SHARPNESS
DYNAMIC IRIS
WA VEFORM MONITO R
SPLIT  ADJAST
ADVA NCED MENU
PICTURE MEMOR YSIMPLE 0
0
0
0
0
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
FRETURN
FUNCTION DISABLE
ENTER
SELECT
Items that can be adjusted
 
z
Submenu items Page
[CONTRAST] 40
[BRIGHTNESS] 40
[COLOR] 40
[TINT] 40
[COLOR TEMPERATURE] 41
[SHARPNESS] 41
[ADVANCED MENU] 45
Press the  button until getting 
6)  
back to the adjustment screen.
Press the  button.
7)  
SPLIT  ADJUST
SAVE CHANGES?
YES  : SAVE AND QUIT
NO  : QUIT WITHOUT  SAVING
CANCEL  : ADJUST  AGAIN
CANCELYESNO
RETURNSELECT
ENTER
The confirmation message is displayed.
 
 
z
Select [YES] with the ◄► buttons and press the 
 button to apply the changes and return 
to the frozen screen. 
Select [NO] with the ◄► buttons and press the 
 button to return to the frozen screen 
without applying changes. 
Note
Select [CANCEL] on the confirmation message and press 
 
z
the  button to return to the adjustment screen.
Press the  button.
8)  
You can now view the projected video with the 
 
z
adjustments applied. 
						

							[PICTURE] menu
ENGLISH - 45
Settings
Note
You cannot adjust menu items that are displayed in grey 
 
z
during split adjustment.
The [KEYSTONE] of [POSITION] becomes inactive 
 
z
during split adjustment.
When a 3D signal is being input (including converting 2D 
 
z
to 3D), the [SPLIT ADJUST] cannot be executed.
[ADVANCED MENU]
You can perform more detailed image adjustment 
manually.
Press the  button
The [ADVANCED MENU] menu is displayed.
 
z
 
■ [GAMMA ADJUSTMENT]
You can make detailed adjustments to the light intensity of 
each input signal level by using the [ADVANCED] mode, 
or adjust at 3 levels (high, mid, low) by using the [SIMPLE] 
mode.
Note
You can only carry out the [GAMMA ADJUSTMENT] 
 
z
through either the [ADVANCED] or [SIMPLE] mode. Both 
settings cannot be used at the same time.
 
Adjusting the gamma (when [ADVANCED] 
 
●
is selected for [ADJUSTMENT MODE])
Press the ◄► buttons to select 
1)  
[ADVANCED].
GAMMA  ADJUSTMENT
ADJUSTMENT  MODE
GAMMA  HIGH
GAMMA  MID
GAMMA  LOW
POINT
Y  ADJUST
R  ADJUST
G  ADJUST
B  ADJUST
INITIALIZE ADVA
NCED
5
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
Press the ▲▼ buttons to select [Y ADJUST] 
2 )  
and then press the  button.
The [Y ADJUST] menu is displayed and a 
 
z
maximum of 9 points are adjustable.
Y ADJUST
POINT5
0% 50%100%
INPUT
OUTPUT
INPUTOUTPUT50%0
(A)
Displays information about the current selected point 
(A) . 
Default setting:
POINT [5]   INPUT [50 %]   OUTPUT [0]
[POINT]  
[1] to [9] Display the present selected point 
number. 
Numbers 1 to 9 are displayed from 
the left of the input signal level.
 
Your selected point is indicated in 
yellow on the graph.
[INPUT]  [1 %] to   
[99 %] Display the input level of the present 
selected point.
 
Setting range: from 1 to 99 % in 
increments of 1 %. 
Default settings: 10, 20,  
30, 40, 50, 60,  
70, 80, 90 %
[OUTPUT] [-252] to [+252] Display the output level of the present 
selected point.
 
Adjustable range depends on the 
input level.  
Default setting: 0 
						

							[PICTURE] menu
46 - ENGLISH
Settings
Adjust the tone with the ▲▼
3)  ▲
▼ buttons, 
 button,  button, or 
 button.
a.  Changing the selected point
Using the remote control
 
z
The selection point moves one point to the right each 
time the  button is pressed. The default 
setting is point 5. 
Ex. 5 -> 6 ->...-> 9 -> 1 ->...
Y  ADJUST
POINT
0% 50%100%
INPUT
OUTPUT
INPUTOUTPUT50%+ 10
5
Y  ADJUST
POINT
0% 50%100%
INPUT
OUTPUT
INPUTOUTPUT60%0
6
Using the device control
 
z
You can also change the [POINT] from the [GAMMA 
ADJUSTMENT] menu directly. 
Use ▲ ▼ to select [POINT] and ◄ ► to change the 
point.
GAMMA  ADJUSTMENT
ADJUSTMENT  MODE
GAMMA  HIGH
GAMMA  MID
GAMMA  LOW
POINT
Y  ADJUST
R  ADJUST
GA DJUST ADVA
NCED
5
PICTURE
POSITION
LANGUAGE
3D SETTINGS
GAMMA  ADJUSTMENT
ADJUSTMENT  MODE
GAMMA  HIGH
GAMMA  MID
GAMMA  LOW
POINT
Y  ADJUST
R  ADJUST
GA DJUST ADVA
NCED
6
PICTURE
POSITION
LANGUAGE
3D SETTINGS
b.  Adjusting the input level
To adjust the input level from the present setting, 
 
z
press 
▲
▼ continuously until it reaches your 
desired level. (It may be moved left and right.)
Setting range: from 1 to 99 % in increments of 
 
z
1 %.  (However, it cannot be set beyond the 
adjacent points.)
Only available to adjust the input level in the 
 
z
[Y ADJUST] screen and not other screens. 
(Input level cannot be adjusted on the [R/G/B 
ADJUST] screen.)
Ex.   Press ◄ in the [Y ADJUST] screen and move the 
selected point leftward.
Y ADJUST
POINT
0% 50%100%
INPUT
OUTPUT
INPUTOUTPUT50%0
5
Y  ADJUST
POINT
0% 50%100%
INPUT
OUTPUT
INPUTOUTPUT44%0
5
MOVE LEFT
Setting range: 1 to 99 % 
						

							[PICTURE] menu
ENGLISH - 47
Settings
c. Adjusting the output level
To adjust the output level from the present setting, 
 
z
press ▲ ▼ continuously until it reaches to your 
desired level. (It may be moved up and down.)
Output level can be adjusted for each color on 
 
z
the [R/G/B ADJUST] screen.
Ex.   Press ▲ in the [Y ADJUST] screen and move the 
selected point upward.
Y ADJUST
POINT
0% 50%100%
INPUT
OUTPUT
INPUTOUTPUT50%+ 10
5
Setting range: -252 to +252
Y  ADJUST
POINT
0% 50%100%
INPUT
OUTPUT
INPUTOUTPUT50%+ 30
5
MOVE 
UP
d. Changing the adjustment by different color 
types
The settings change as follows each time the 
 
z
 button is pressed.
Y ADJUSTR ADJUST
B ADJUSTG ADJUST
You can also switch each different color adjustment 
menu through the [GAMMA ADJUSTMENT] menu. 
Select your required color adjustment ([Y ADJUST], 
[R ADJUST], [G ADJUST], [B ADJUST]) with ▲ ▼ 
in the [GAMMA ADJUSTMENT] menu and press the 
 button.
GAMMA  ADJUSTMENT
ADJUSTMENT  MODE
GAMMA  HIGH
GAMMA  MID
GAMMA  LOW
POINT
Y  ADJUST
R  ADJUST
G  ADJUST
B  ADJUST
INITIALIZE ADVA
NCED
5
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
R ADJUST
POINT
0% 50%100%
INPUT
OUTPUT
INPUTOUTPUT50%+ 10
5
e.  Setting the output levels back to the default 
setting
To set the output level on the selected point back 
 
z
to the default setting “0”, press the  
button on the remote control.
Note
Individual input levels cannot be set back to their default 
 
z
settings by pressing the  button. Press 
▲
▼ 
to move back themselves if needed. 
						

							[PICTURE] menu
48 - ENGLISH
Settings
Initialize the gamma adjustment results
 
●
GAMMA  ADJUSTMENT
ADJUSTMENT  MODE
GAMMA  HIGH
GAMMA  MID
GAMMA  LOW
POINT
Y  ADJUST
R  ADJUST
G  ADJUST
B  ADJUST
INITIALIZE ADVA
NCED
5
PICTURE
POSITION
LANGUAGE
3D SETTINGS
LENS CONTROL OPTION
Press the ▲▼ buttons to select 
1)  
[INITIALIZE] and press the  
button.
The confirmation message is displayed for the 
 
z
gamma initialization.
GAMMA  ADJUSTMENT
INITIALIZE GAMMA  ADJUSTMENT.
CANCELOK
Select [OK] with the 
2)  ▲
▼ buttons and press 
the button.
Your gamma settings in [ADVANCED] mode will 
 
z
return to factory default settings.
Note
Initialization is not available in [SIMPLE] mode.
 
z
Adjusting the gamma (when [SIMPLE] is 
 
●
selected for [ADJUSTMENT MODE])
Press the ◄► buttons to select [SIMPLE].
1)  
GAMMA  ADJUSTMENT
ADJUSTMENT  MODE
GAMMA  HIGH
GAMMA  MID
GAMMA  LOW
POINT
Y  ADJUST
R  ADJUST
GA DJUST SIMPLE
0
0
0
PICTURE
POSITION
LANGUAGE
3D SETTINGS
Select item with the ▲▼ buttons, and 
2)  
adjust with the 
▲
▼ buttons.
You can adjust linear intensity at 3 levels (high, 
 
z
mid, low). Press ▲ ▼ to select your required 
gamma levels.
-1+1
 
GAMMA  HIGH
GAMMA  MID
GAMMA  LOW 0
0
0
[ADVANCED MENU] menu items
Default 
setting
[GAMMA HIGH] 0
[GAMMA MID] 0
[GAMMA LOW] 0
Setting range: -8 to +8
 
z
 
■ [CONTRAST]
You can adjust color temperatures centering mainly on 
white. 
R (RED), G (GREEN), B (BLUE)
-
1+1
[ADVANCED MENU] menu items Default 
setting
[CONTRAST R] 0
[CONTRAST G] 0
[CONTRAST B] 0
Setting range: -32 to +32
 
z
 
■ [BRIGHTNESS]
You can adjust color temperatures centering mainly on black. 
 R (RED), G (GREEN), B (BLUE)
-
1+1
[ADVANCED MENU] menu items Default 
setting
[BRIGHTNESS R] 0
[BRIGHTNESS G] 0
[BRIGHTNESS B] 0
Setting range: -16 to +16
 
z
 
■ [NR]
You can eliminate the noise that occurs when the input 
signal deteriorates.
WeakenStrengthen
Setting range: 0 to +3
 
z 
						

							[PICTURE] menu
ENGLISH - 49
Settings
 
■ [MPEG NR]
You can eliminate the noise that occurs upon projection for 
videos that use MPEG compression.
WeakenStrengthen
Setting range: 0 to +3
 
z
Attention
Use a strong setting when projecting an MPEG video.
 
z
COMPUTER (RGB) signal is not supported.
 
z
 
■ [FRAME CREATION]
You can activate the rendering system for fast motion 
frames with fewer afterimage.
Switch settingsSwitch settings
[OFF][MODE1]
[MODE3][MODE2]
[OFF] 
Deactivate
[MODE1] Setting for a standard image
[MODE2]  Setting for a theater image
[MODE3]  Setting for a fast moving image
Note
With some of the images, it might be difficult to see a 
 
z
difference in result.
If [FRAME CREATION] is set to active, video may be 
 
z
delayed in some cases. In this case, select [OFF].
This cannot be set to active when [2D TO 3D] 
 
z
(
 page 66) is enabled.
 
■ [COLOR MANAGEMENT]
For the selected [PICTURE MODE], you can adjust a 
selected color individually with [CURSOR] mode or adjust 
the six color components (Red, Green, Blue, Cyan, 
Magenta, Yellow) with [RGBCMY] mode.
 
Adjustment results can be saved as a profile and called 
later.
 
● Create a new profile
Note
[COLOR MANAGEMENT] will be unable to adjust with 
 
z
the setting of [REC709] in [PICTURE MODE], when 
HDMI signal is selected.
When the input signal is switched while adjusting, 
 
z
adjustment details are not  saved.
If there is another area, which has the exact same or 
 
z
similar color as the target on the same screen, these 
colors will be adjusted as well.
You can adjust all colors except white, gray and black.
 
z
If you edit a single color to be individual different colors, 
 
z
the desired color may not be achieved.
When a 3D signal is being input (including converting 2D 
 
z
to 3D), [COLOR MANAGEMENT] cannot be executed.
Adjusting the selected color (when 
 
z
[CURSOR] is selected for [ADJUSTMENT 
MODE])
Select the desired color with a cursor and adjust.
Press the ◄► buttons to select [CURSOR] 
1)  
in [ADJUSTMENT MODE].
COLOR MANAGEMENT
PROFILE
ADJUSTMENT  MODE
ST AR T ADJUSTMENT
LOG NORMAL
CURSOR
Press the ▲▼ buttons to select [START 
2)  
ADJUSTMENT] and press the  
button.
The cross cursor 
 
z (A)
 is displayed, and the 
projected image is captured.
 Screen
Move the cursor with the ▲▼◄► buttons 
3)  
to the required place to select a color.
Align the center of the cross cursor on the point 
 
z
in the projected image to be adjusted. 
						

							[PICTURE] menu
50 - ENGLISH
Settings
Press the  button.
4)  
[CURSOR] menu 
 
z (B)
 and the color selected  (C) 
are displayed.
 
COLOR
TINT
BRIGHTNESS
CURSOR0
0
0
RETURN
DEF
AULT
SELECT ENTER
Screen
Note
In some cases you may be unable to adjust when the 
 
z
very edge point of the projection area is selected.
You can create a profile only when [ADJUSTMENT 
 
z
MODE] is set to either [CURSOR] or [RGBCMY]. A profile 
cannot be created from both adjustments. 
White, gray and black cannot be edited.
 
z
Press the ▲▼ buttons to select a menu 
5)  
item and the ◄► buttons to adjust each 
item level.
[COLOR] Adjust the vividness of the 
color.Setting range:  
 
z
−30 to +30
[TINT] Adjust the color tone.Setting range:  
 
z
−30 to +30
[BRIGHTNESS]
Adjust the brightness of the 
color.
Setting range:  
 
z
−20 to +20
The default setting for each item is [0]. 
 
z
After adjusting, the post-adjustment color  (D) is 
displayed.
 
COLOR
TINT
BRIGHTNESS
CURSOR
RETURN
DEF
AULT
SELECT ENTER
0
0
0
Screen
Press the  button.
6)  
[PROCESSING] message is displayed for a few 
 
z
seconds and the result is stored in [LOG]. 
You can store up to 8 logs under [LOG]. Press 
the  or  button to return 
to the previous menu. Repeat from step 3) to 
store more adjustments.
Press the  button or  
7)  
button twice.
This returns you to the [COLOR 
 
z
MANAGEMENT] menu.
Adjusting the selected color (when 
 
z
[R G BCM Y] is  s ele cte d  f o r [ A DJU STM EN T 
MODE])
Select the color from 6 different color types ([RED], 
[GREEN], [BLUE], [CYAN], [MAGENTA], [YELLOW]) and 
adjust [COLOR], [TINT] and [BRIGHTNESS].
Press the ◄► buttons to select [RGBCMY] 
1)  
in [ADJUSTMENT MODE].
COLOR MANAGEMENT
PROFILE
ADJUSTMENT  MODE
ST AR T ADJUSTMENT
LOG NORMAL
RGBCMY
Press the ▲▼ buttons to select [START 
2)  
ADJUSTMENT] and press the  
button.
Press the ▲▼ buttons to select your 
3)  
desired color and press the  
button.
RGBCMY  ADJUSTMENT
RED
GREEN
BLUE
CY AN
MAGENTA
YELLOW
Menu 
 
z (B)
 and the base color  (C) is displayed.
 
COLOR
TINT
BRIGHTNESS
RED0
0
0
RETURN
DEF
AULT
SELECT ENTER
Screen