Panasonic Projector Pt Ae3000e Operating Instructions

							ENGLISH - 11
Preparation
About Your Projector
Remote control
NOTE:
• Do not drop the remote control.
• Avoid contact with liquids or moisture.
• Use manganese batteries or alkaline batteries with the remote control.
• Do not attempt to modify or disassemble the remote control. Contact an Authorised Service Centre for repairs.
• Do not keep pressing the remote control buttons as this may shorten battery life.
• See “Remote control operation” on page 23.
Battery compartment
1. Press the tab and lift up the cover.
2. Insert the batteries according to the polarity diagram indicated 
inside.
Power button
While the MAIN POWER 
button is on, switch between 
standby mode and projection 
mode. (page 21)
Remote control signal emitter
Emit remote control signal. (page 23)
Button backlight
When any button is pressed, the button 
backlight is lit. Without any operation, it 
gets darker after 5 seconds and goes off 
after next 5 seconds.
Display the PICTURE menu 
or ADVANCED MENU. 
(page 23)
Switch to cycle through the 
PICTURE MODE. (page 23)
Switch to cycle through the 
aspect ratio. (page 24)
Display the main menu or 
return to the previous menu. 
(page 29)
Navigate through the 
menus with FGIH, 
and activate the menu 
item with the ENTER 
button. (page 29)
Reset some of the settings to 
the factory default. (page 28)
Switch to cycle through 
the input method. 
(page 28)
Display the LENS CONTROL 
menu. (page 23)
Display the MEMORY LOAD 
menu. (page 24)
Display the COLOUR 
MANAGEMENT menu. 
(page 26)
Display the input waveform. 
(page 24)
Return to the previous 
menu. (page 29)
Capture the projected image 
as a still image. (page 28)
Activate the assigned 
function from the menu 
options for shortcut. 
(page 42) 
						

							Preparation
About Your Projector
12 - ENGLISH
JTop and front view
Projector body
NOTE:
• Do not cover the ventilation openings or place anything within 50 cm (20) of them as this may cause damage or injury.
• While the projector is not in use, keep the lens cover attached to protect the lens.
(Push to open/close the cover.)
RETURN
Return to the previous menu. 
(page 29)FOCUS and ZOOM
Adjust the focus and size of the 
image. (page 22)
Navigate through the menus with F G H I, 
and activate the menu item with the ENTER 
button. (page 29)
Power
While the MAIN POWER is on, switch between 
standby mode and projection mode. (page 21)
MENU
Display the main menu.
Return to the previous menu. (page 29)
Air exhaust port
Heated air comes out of 
this opening.
Projection lens
Lens shift dial • Vertical
(page 16)Lens shift dial • Horizontal
(page 16)
Lens cover
Protects the projection lens 
from dust or dirt.Remote control signal 
receptor
(page 23)Air exhaust port
Heated air comes 
out of this opening.
Power/LAMP/TEMP 
indicators
(page 20/page 45)
Air filter
(page 46)
MAIN POWER
Switch the projector on/off. 
(page 21)
INPUT SELECT
Switch to cycle through the 
input method. (page 22) 
						

							Preparation
About Your Projector
ENGLISH - 13
JBack and bottom view
NOTE:
• Do not cover the ventilation openings or place anything within 50 cm (20) of them as this may cause damage or injury.
• The projector should only be used with the attached mains lead to ensure optimum performance and avoid damage to the 
projector.
• Do not open the top cover other than replacing the lamp unit.
Connecting 
terminals 
(page 18)
Air intake port
Security lock
Attach the commercial shackle lock 
which is provided with the projector. 
Compatible with the Kensington 
MicroSaver Security System.
Top cover
Hold the top cover at the back corner 
and slightly push up to open. 
(page 47)
Air intake port
AC IN
Connect the mains lead to 
supply electronic power to the 
projector. (page 19)
Safety cable attachment point
Attach the safety cable when 
mounted on the ceiling. 
(page 56)
COMPUTER IN
Connect an RGB signal cable 
from your PC.
S-VIDEO IN
Connect a S-VIDEO 
signal cable.
VIDEO IN
Connect an RCA 
composite video cable.
COMPONENT IN
Connect YP
BPR signal cables.
Lens cover attachment holeFront leg adjusters
Screw up/down to adjust the 
projection angle. (page 15)
Front leg adjusters
Screw up/down to adjust the 
projection angle. (page 15)
SERIAL
Connect a compatible cable for 
controlling the projector 
remotely via your computer. 
(page 51)HDMI IN
Connect HDMI signal cables. 
						

							Getting Started
14 - ENGLISH
Setting up
You can adjust the projection size with 2.0x zoom lens. Calculate and define the throw distance as follows.
All measurements and the calculation results bellow are approximate and may differ from the actual measurements.
JCalculation methods for screen dimensions
You can calculate more detailed screen dimension from the screen diagonal.
 16 : 9 size
Screen width (SW) and screen height (SH)
SW (m)= SD (m) x 0.872 SH (m) = SD (m) x 0.490
Minimum distance (LW) and maximum distance (LT)
LW (m) = SD (m) x 1.189 - 0.04 LT (m) = SD (m) x 2.378 - 0.05
 2.35 : 1 size
Screen width (SW) and screen height (SH)
SW (m)= SD (m) x 0.920 SH (m) = SD (m) x 0.392
Minimum distance (LW) and maximum distance (LT)
LW (m) = SD (m) x 1.256 - 0.04 LT (m) = SD (m) x 1.899 - 0.05
Screen size and throw distance
Throw distance (16 : 9)Throw distance (2.35 : 1)
Screen Diagonal 
(SD)Minimum distance 
(LW)Maximum distance 
(LT)Minimum distance 
(LW)Maximum distance 
(LT)
1.02 m (40) 1.2 m (311) 2.3 m (76) 1.3 m (43)
1.27 m (50) 1.5 m (411) 2.9 m (96) 1.6 m (52) 2.3 m (76)
1.52 m  (60) 1.8 m (510) 3.5 m (115) 1.9 m (62) 2.8 m (92)
1.78 m (70) 2.1 m (610) 4.1 m (135) 2.2 m (72) 3.3 m (109)
2.03 m (80) 2.4 m (710) 4.7 m (155) 2.6 m (86) 3.8 m (125)
2.29 m  (90) 2.7 m (810) 5.3 m (174) 2.9 m (96) 4.2 m (139)
2.54 m (100) 3.0 m (910) 5.9 m (194) 3.2 m (105) 4.7 m (155)
3.05 m (120) 3.6 m (119) 7.2 m (237) 3.8 m (125) 5.7 m (188)
3.81 m (150) 4.5 m (149) 9.0 m (296) 4.8 m (158) 7.1 m (233)
5.08 m (200) 6.0 m (198) 12.0 m (394) 6.4 m (2011) 9.6 m (315)
NOTE:
• Do not use the projector at a raised or a horizontally tilted position as it may cause 
malfunction of the projector.
• Make sure the projector lens surface is parallel with the screen. You can tilt the projector 
body less than approximately ± 30° vertically. Overtilting may result in shortening the 
component’s life.
• For the best quality of the projection image, install a screen where sun light or room light 
does not shine directly onto the screen. Close window shades or curtains to block the lights.
SD
SW
SH
ScreenProjected image
(Shown as 16:9 size)
-30° +30° 
						

							Getting Started
Setting up
ENGLISH - 15
You can use the projector with any of the following 4 projection methods. To set the desired method in the projector, 
See “INSTALLATION” on page 44.
You can screw up/down the front leg adjusters to control the angle of the projector for adjusting the throwing angle. 
See “Positioning the image” on page 22.
Projection method
JSetting on a desk/floor and 
projecting from front JSetting on a desk/floor and 
projecting from rear
INSTALLATION: FRONT/DESKINSTALLATION: REAR/DESK
JMounting on the ceiling and 
projecting from frontJMounting on the ceiling and 
projecting from rear
INSTALLATION: FRONT/CEILINGINSTALLATION: REAR/CEILING
NOTE:
• A translucent screen is required for rear projection.
• When mounting the projector on the ceiling, the optional ceiling mount bracket (ET-PKE2000, ET-PKE1000S) is required.
• See “Ceiling mount bracket safeguards” on page 56.
Front leg adjusters and throwing angle
NOTE:
• Heated air comes out of the air exhaust port. Do not touch the air exhaust port directly.
• If keystone distortion occurs, see “KEYSTONE” on page 39.
• Screw up the front leg adjusters, and an audible click will be heard as the limit. 
						

							Getting Started
Setting up
16 - ENGLISH
If the projector is not positioned right in front of the centre of the screen, you can adjust the projected image position 
by moving the lens shift dials within the shift range of the lens.
JAdjusting the lens shift dials
QHorizontal shift
You can place the projector where the projector lens is up to 40% horizontally off-centre from the screen and 
then adjust the image position with the Lens shift dial • Horizontal.
QVertical shift
You can place the projector where the projector lens is up to 100% vertically off-centre from the screen and 
then adjust the image position with the Lens shift dial • Vertical.
Lens shift and positioning
Turning the dial clockwise: 
Image moves to the rightUp to about 40 % 
of the projection
Turning the dial counterclockwise: 
Image moves to the left Up to about 40 % 
of the projection
Up to about 100 % 
of the projection
Up to about 100 % 
of the projectionTurning the dial counterclockwise: 
Image moves to the bottom
Turning the dial clockwise: 
Image moves to the top 
						

							Getting Started
Setting up
ENGLISH - 17
JProjector location range
You can determine where to locate the screen and the projector by considering the lens shift possibilities.
QWhen the screen position is fixed
QWhen the projector position is fixed
NOTE:
• When the projector is located right in front of the centre of the screen and the lens shift dials is centred, you will get the 
best quality of the projection image.
• When the Lens shift dial • Vertical is at the vertical limit of the shift range, you cannot turn the dial to the horizontal limit, 
likewise when the Lens shift dial • Horizontal is at the horizontal limit of the shift range, you cannot turn the dial to the 
vertical limit.
• When the projector is tilted and adjusting KEYSTONE, the centre of the screen and the lens need to be realigned.
• Do not force the lens shift dials to turn as this may damage the projector. Turning the dials maximum limit is 4 or 5 times 
from the default position.
H
V
SH
SW
Placement
Centre of lens
Vertical centre of 
screenProjector
Screen
100%
100%
40% 40%
ProjectorShift range
SH
SW 
						

							Getting Started
18 - ENGLISH
Connections
 Read and follow the operating and connecting instructions of each peripheral device.
 The peripheral devices must be turned off.
 Use cables that match each peripheral device to be connected.
 Confirm the type of video signals. See “List of compatible signals” on page 50.
 Audio cables must be connected from each peripheral device directly to the audio reproduction system.
\
Before connecting to the projector
Connecting example: COMPONENT IN/S-VIDEO IN/
VIDEO IN
Connecting example: HDMI IN/COMPUTER IN
NOTE:
• Make sure the HDMI cable is adapted to your HDMI device for proper performance.
• A compatible cable is required for an HDMI 1 080p signal.
• It is possible to connect with DVI devices via a HDMI/DVI conversion adapter, but some equipment may not project the 
image properly or other problems could be encountered. See “Serial terminal” on page 51.
DVD player Video player DVD player To COMPONENT
video output
To VIDEO output
To S-VIDEO output
RGB signal cable
(Commercial item) HDMI cable
(RP-CDHG100: Optional))
To HDMI output
DVD player
Computer 
						

							ENGLISH - 19
Basic Operation
Switching the projector on/off
JConnecting
1. Make sure the shape of the mains plug and the 
AC IN terminal on the back of the projector match, 
then push the plug all the way in.
2. Align the side of the power cord secure lock with 
the side guide rail of the AC IN terminal of the 
projector and slide it in.
3. Place the latch to the latch catcher and press until 
it clicks.
4. Connect the mains lead to a mains socket.
JDisconnecting
1. Unplug the mains lead from the mains socket.
2. Depress the latch and slide the cover off.
3. Slide the power cord secure lock up along the side 
guide rail and remove.
4. Hold the plug and unplug the mains lead from the 
AC IN terminal on the back of the projector.
Mains lead
Rail guide
Latch
Latch
Rail guide
NOTE:
• Do not use other than the provided mains lead.
• Ensure all the input devices are connected and turned off before connecting the mains lead.
• Do not force the connector as this may damage the projector and/or the mains lead.
• Dirt or dust build-up around plugs may cause fire or electrical hazards.
• Switch off the power to the projector when not in use. 
						

							Basic Operation
Switching the projector on/off
20 - ENGLISH
Power indicator informs you the status of the power.
 When the TEMP indicator is flashing, the power 
indicator will not light.
Power indicator
Power indicator
Indicator statusStatus
No illumination or flashingThe MAIN POWER button is switched off.
Red LitThe MAIN POWER button is switched on and the projector is in standby mode.
GreenFlashingThe power button is switched on and the projector is getting ready to project.
LitProjecting.
OrangeLitThe power button is switched off and the projector is cooling the lamp.
FlashingThe power button is switched on again when cooling the lamp and recovering to 
projection mode. Recovery may take a while.
NOTE:
• See “TEMP indicator” on page 45.
• While the projector is cooling the lamp, do not switch the MAIN POWER button off or unplug the mains lead.
• The electric consumption in standby mode is 0.08 W.