Panasonic Personal Hair Trimmer Er 327 Operating Instructions

Operating Instructions
Personal Hair Trimmer
Model No. ER327
Before operating this unit, please read these instructions carefully. No. 1 EN, ES (U.S.A.)Printed in Japan
Imprimé au Japon
IN USA CONTACT:
Panasonic Consumer Electronics Company
One Panasonic Way 2F-3 Secaucus, NJ 07094
IN PUERTO RICO CONTACT:
Panasonic Sales Company
Division of Matsushita Electric of Puerto Rico, Inc.
San Gabriel Industrial Park 65th infantry Avenue KM9.5
Carolina, Puerto Rico 00630
En México:
Panasonic de México, S.A de...

IndexENGLISH Page   2
ESPAÑOL Página 22
12
Caution
Do not place the trimmer in locations that are subject to high humidi-
ty.
Clean the body only with a soft cloth slightly dampened with water or 
soapy water. Never use a corrosive cleaner such as benzine or 
bleach.
Never immerse the trimmer in water or apply to wet hair.
Keep out of reach of children.
Do not use on animals.
The trimmer may become warm during operation. This is normal.
Never tamper with the moving parts.
Do not disassemble the trimmer....

Slide open
Comb
BodyTrimming height 
dial Trimmer comb 
attachment
Finishing
adjustment switch
ON/OFF Switch Trimming height
display
Battery cover
Parts NameBefore use
Parts identification
Inserting the batteries
Hair clipper 
attachment
Body without the Trimmer comb attachment or hair clipper
attachmentBody (front)
Thinning plate
Cleaning brushThinning plate
lock button
Body (back)
Accessories
BladeCleaning lever
Oil
3
Battery cover
Battery cover
Remove the battery cover.
1
3
Back
2
4
Turn the trimmer...

Drape a towel or cape
over the shoulders.
1
Turn the switch to [0].* The trimmer comb attachment will not 
  slide if the switch is [1].
1
Turn the 5 position dial until 
it clicks, then adjust the trim-
mer comb attachment to 
the desired length.
2
Comb the hair thorough-
ly to remove any tangles 
or knots.
2
Preparations before cutting
Before use
Hair areas which can be 
trimmed
Adjusting the length of the
Trimmer Comb attachmentAfter adjusting the length, turn 
the switch to [1] and confirm the...

Before use
Attaching and removing
the Trimmer Comb attachment
RemovingTurn the switch to [0], 
confirm that the dial 
guide is set to [1] and 
then gently pull off to 
remove.AttachingTurn the switch to [0], 
confirm that the dial 
guide is set to [1] and 
then attach it to the 
body.Hold down the dial 
while attaching and 
push the attachment 
until it clicks.
RemovingTurn the switch to [0] 
and slide the attach-
ment to remove.Hold down the dial dur-
ing removal.AttachingTurn the switch to [0] 
and...

Cutting
procedure
Cutting the sides and back 
Cutting by adjusting the length
of the Trimmer Comb attachment
Cut against the
direction the hair lays
Trimming height
Secure the trimmer
comb attachment
before cutting.
The trimmer will not
cut more than the set
trimming height.The actual hair length will be longer than the set trimming height.
Do not use the trim-
mer switch side up as 
shown in the illustra-
tion on the left. This 
will result in cutting 
more than the desired 
length.
Side with
the...

Cutting
procedure
Cutting the sides to the back
Trimming height
25 to 20mm 
(15/16 to 13/16)
Trimming height
15 to 10mm 
(9/16 to 3/8)
Cut from25 - 20mm
(15/16 - 13/16) 
Cutting around the ears
Make sure the switch is facing downwards
and cut by moving the trimmer upwards.
Hold down
the ears with
your fingers
Make sure the switch is facing downwards
and cut by moving the trimmer upwards.
4
Cutting between the sides and backCut between the already
cut sides and back bit by
bit with the use of thehair...

Selecting the thickness of the finish
Move the trimmer down-
wards in the direction of 
the arrows when cutting 
around the ears.
*Cutting areas with excessive hair.Having secured the hair clipper attachment Make sure the switch is facing upwards and cut by 
moving the trimmer downwards.
Overall hair cutting
Cutting
procedure
approx. 7mm (1/4)
(Finishing thickness of
   approximately 7mm)Short finishLong finish
approx. 9mm (3/8)
Finish adjustment switch
ScalpScalp
9mm
   (3/8)
7mm
   (1/4)
13
(Approx....

Thinning the bangs
Make sure the switch is facing up-
ward and move the thinning plate 
down the hair as if combing.
Raise thethinning plate
Lower thethinning plate
Make sure the
switch is
facing upward.
Little by little comb the trimmer through the hair the tip of the fringe while continuously checking the result.
Without any attachments
Fine trimmingCutting
procedure
The mechanism of the thinning plate
Cuts only the hairs thatenter these areas.
Apply the blade directly to the skin.
The thinning plate...

Attaching
the blade Turn the switch to [0].
After use
Maintenance
Press the blade
*Place your other hand under the blade
to prevent it from falling.
Until there is a click.Press
1
Insert the hookInsert the blade
A
into the slot     .
B
Press the blade
B
A
2
1718
Removing
the blade
Make sure the Pop-up 
Trimmer is in the [Down] 
position.
Apply slight pressure from the back 
of the trimmer against the blade. 
The blade should gently pop-out.