Panasonic Network Camera Wv Sw458m Installation Guide

21
x Determine the direction of the mount bracket according to the installation environment (how the 
cables are wired, etc.) before mounting it to a ceiling or a wall by fixing 4 screws (locally pro-
cured).
  The direction of the camera in relation to the mount bracket is the 4 directions as shown in the 
illustration.
IMPORTANT:
	• 	 	For	 mounting	 a	 camera	 on	 a	 concrete	 surface,	 use	 an	
anchor bolt (M4) or an AY plug bolt (M4) for installing.
  
(Recommended tightening torque M4: 1.6  N·m...

22

Align the direction of the conduit to the direction of the female thread for the conduit on the mount 
bracket, and mount the mount bracket to hole A or hole B on the ceiling or wall.
[For use of the hole A]
Note:
	 •	 Only	the	same	type	of	holes,	A or B, shall be used for mounting.
Conduit
Female thread for the conduit
Mount bracket
(accessory)
Fixing screws 
(4 pcs., locally procured)
138 mm
{5-7/16 inches}
85 mm
{3-11/32 inches}
(d (d
(d
(c
(c
(d
(d(d
For use of the hole 
85 mm 138 mm
{5-7/16...

23
c  In the direction determined in  x, fix the camera attachment (accessory) on the mount bracket 
using the fixing screws (accessory).
   (Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})
Note:
	•		The	direction	of	“gTOP” on the camera attachment (accessory) determines the upwards 
direction of the image on the PC monitor.
	•		For	ceiling	mounting:  Determine the direction that you want images to be displayed upwards on the PC monitor, 
and then mount the camera attachment (accessory) with “...

24
IMPORTANT:
	 •	 When	inserting	an	SD	memory	card,	make	sure	the	direction.
	 •	 Before	 removing	 the	 SD	 memory	 card,	 select	 “Not	 use”	 for	 “SD	 memory	 card”	 on	 the	  
[SD memory card] tab of the “Basic” page first. Turn off the power after “Not use” selection, 
and then unload the SD memory card. When the SD memory card is inserted or removed with 
the power on, data in the SD memory card may be damaged. (
☞  Operating Instructions 
(included in the CD-ROM))
z  Loosen the SD memory card...

25
Network cableM12 connector (male)
Alarm input/output cable 4P alarm cable (accessory) LAN cable (category 5 or better)
Power cable 
(12 V DC) 2P power cable (accessory)
12 V DC (red)
GND (black)
Microphone/line input cable (white)
Audio output cable (black)
Caution:
	 •	 ONLY	 CONNECT	 12	 V	 DC	 CLASS	 2	 POWER	 SUPPLY	 (UL	 1310/CSA	 223)	 or	 LIMITED	 POWER SOURCE (IEC/EN/UL/CSA 60950-1).
	 •	 A	 READILY	 ACCESSIBLE	 DISCONNECT	 DEVICE	 SHALL	 BE	 INCORPORATED	 TO	 THE	 EQUIPMENT POWERED BY 12 V DC...

26
z • Connecting an external microphone and an external speaker
   Connect the microphone/line input cable and the microphone.
Input impedance:  2 kΩ±10 %
Recommended cable length:  Less than 1 m {3.3 feet} (for microphone input)
   Less than 10 m {33 feet} (for line input)
Recommended microphone:  Plug-in power type microphone (option)
   Connect a monaural mini plug (ø3.5 mm).
•	Supply	voltage:	 2.5	V	±0.5	V
•	Recommended	sensitivity	  of microphone:  −48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)
IMPORTANT:
	•...

27
IMPORTANT:
	•		Input	 and	 output	 of	 the	 External	 I/O	 terminal	 2	 and	 3	 can	 be	 switched	 by	 configuring	 the	setting. “Off” is selected by default. It is possible to determine whether or not\
 to receive 
input from External I/O terminal 2 and 3 (ALARM IN2, 3) by selecting “Off”, “Alarm input”, 
“Alarm output” or “AUX output” for “Terminal 2” or “Terminal 3” on the [Alarm] tab of the 
“Alarm” page. Refer to the Operating Instructions on the provided CD-ROM for further 
information. 
	•...

28
Waterproof treatment for the cable joint sections
Adequate waterproof treatment is required for the cables when installing the camera with cables 
exposed or installing it under the eaves. The camera body is waterproof, but the cable ends are not 
waterproof.
Be sure to use the supplied waterproof tape at the points where the cables are connected to apply 
waterproof treatment in the following procedure. Failure to observe this or use of a tape other than 
the provided waterproof tape (such as a vinyl...

29
Connection example when connecting to a network using a 
PoE hub 
Powered speaker 
(option)
Powered speaker 
(option)Microphone 
(option)
Microphone 
(option) PoE device (hub)
LAN cable 
(category 5 or better,  straight, STP*)
LAN cable 
(category 5 or better,  straight, STP*)LAN cable 
(category 5 or better,
 
straight, STP*)
PC

LAN cable (category 5 or better, straight, STP*)
* E model only
IMPORTANT: 
	 •	 Use	a	switching	hub	or	a	router	which	is	compliant	with	10BASE-T/100BASE-TX.
	 •	 When...

30
Camera mounting
Installation shall be conducted after turning off each device.
z Attach the camera attachment (accessory) on the ceiling or wall.

Secure the camera attachment (accessory) to the two-gang junction box (loc\
ally procured). (☞ Pages 18 and 19)
 SW458M
Attach the camera attachment (accessory) using the installation templa\
te label (accessory). (☞ Page 19)
x Connect each cable. (☞ Page 25) Waterproof the connecting portion. (☞ Page 28)
c Using the camera attachment position marker as a...