Panasonic Network Camera KX-HCM280A Installation Guide

Installation/Troubleshooting
[For assistance, please call: 1-800-272-7033]                                 21
6.To register with the Viewnetcam.com FREE DDNS service, check [Register 
with Viewnetcam.com] and click [Next].
Viewnetcam.com FREE DDNS service
See page 23 for Viewnetcam.com information. For detailed information, 
access at http://www.viewnetcam.com.
 If you have multiple cameras, you can use Viewnetcam.com service 
registering it only for a camera.
 If you select [Disable], skip to step 9....

Installation/Troubleshooting
22
9.When Setup complete is displayed, and click [To Single Camera page].
 The port number must be specified at the end of camera URL.
Using port 80:
http://(Cameraname).viewnetcam.com
or http://IP Address
Using any other port:
http://(Cameraname).viewnetcam.com:Port Number
or http://IP Address:Port Number
10.When the Single Camera page is displayed, the setup is completed.
Note
 The banner is displayed only when Internet access is allowed on the 
camera.
 To insure that...

Installation/Troubleshooting
[For assistance, please call: 1-800-272-7033]                                 23
1.8 Viewnetcam.com Service (IPv4/IPv6)
Viewnetcam.com is a free dynamic DNS (DDNS) service provided by Panasonic. 
It allows you to choose an easy-to-remember address (such as 
bob.viewnetcam.com) that you can use to view images from your camera over the 
Internet. This service is compatible with both IPv4 and IPv6 addresses.
What is the advantage of Viewnetcam.com service?
In order to view...

Installation/Troubleshooting
24
Note
 Ask your ISP about what type of IP address you are using.
 Some ISPs assign you a local IP address. In this case, you cannot use the 
Viewnetcam.com service. Ask you ISP about what type of IP address you 
are using.
 If the camera is using a port number other than 80, the port number must 
be specified at the end of the Viewnetcam URL. For example:
Using port 80: http://(Cameraname).viewnetcam.com
Using any other port: http://(Cameraname).viewnetcam.com:Port...

Installation/Troubleshooting
[For assistance, please call: 1-800-272-7033]                                 25
1.9 Connecting the Camera to a Router 
Supporting UPnP™ (IPv4 Only)
To allow access from the Internet with a router supporting UPnP™, follow the 
procedures shown on page 19.
Note
 In some routers, the UPnP™ feature is disabled by default. Enable your 
routers UPnP™ feature following the router manual before you set up the 
camera. See the Panasonic Network Camera support website at http://...

Installation/Troubleshooting
26
1.10 Connecting the Camera to a Router Not 
Supporting UPnP™ (IPv4 Only)
To allow access from the Internet with a router not supporting UPnP™, follow the 
procedures below.
1.Select [Static] on the Network (IPv4) page.
2.Enable port forwarding on the router.
Using the IP address and port number note written on step 1-(3), enable port 
forwarding on the router. See the router manual for how to enable port 
forwarding.
3.Register with the Viewnetcam.com service.
Port...

Installation/Troubleshooting
[For assistance, please call: 1-800-272-7033]                                 27
1.11 Setting up the Camera Using the MAC 
Address on the Setup Program
The Setup Program may not list any cameras due to your firewall or antivirus 
software settings on your PC. If you cannot disable your firewall or antivirus 
software, you can set up the camera using the camera MAC address as shown 
below.
1.Enter the camera MAC address in the data field, and click [Set up camera].
Note
The...

Installation/Troubleshooting
28
3.Enter the user name and password, and click [Save].
4.The Enter Network Password window is displayed. Enter the user name and 
password that were set, and click [OK].
kxhcm280ait.book  28 ページ  ２００５年３月９日　水曜日　午後１時２３分 

Installation/Troubleshooting
[For assistance, please call: 1-800-272-7033]                                 29
5.When the Single Camera page is displayed, the setup is completed.
 If Security Warning window is displayed, click [Yes] (see page 32).
 See page 33 for Security Warning window when using Microsoft Windows 
XP Service Pack 2.
Note
 See page 15 of the Operating Instructions on the Setup CD-ROM for the 
Single Camera page.
 If you enable the Internet access to the camera, follow the procedures...

Installation/Troubleshooting
30
1.12 Confirming the Camera Image
1.Start up the web browser on your PC.
2.Enter http://IPv4 Address (or URL):Port Number on the address bar, and 
press [Enter] on the keyboard.
 When port number is 80 (default), you do not need to enter port number. 
See page 42 of the Operating Instructions on the Setup CD-ROM for 
details about port number.
 For IPv6 connection, see page 13 and page 14 of the Operating 
Instructions on the Setup CD-ROM and prepare the requirements....