Panasonic Network Camera Bl Vp104 Quick Reference Guide For Setup

							In case of Wired ConnectionIn case of Wireless Connection1. Connect the LAN cable to the camera and the router.
2. Connect the AC adaptor cord to the DC IN jack.
3. Plug the AC adaptor into the power outlet, then go to Step2.
2. Connect the AC adaptor cord to the DC IN 
jack.
3. Plug the AC adaptor into the power outlet.5. Press and hold down the WIRELESS button of the camera for
    a second or more until the indicator blinks orange.
    
It will restart, if this is successful. Please wait for about 2 minutes.
1. No LAN cable connection is re
quired if router su
pp
orts WPS.
*1
                       Settin
g
 of the Camera with CD from PC
1. Insert the CD-ROM into your PC.
2. Click the [Run] of the IP Setting Software.
2
3. Select the camera you want to configure, and click [Access Camera].
3
4. The user authentication window will be
    displayed and then enter the default
    User name and Password, and log in.
User name: admin
Password : 12345
6. The WIRELESS indicator turns Green, then go to Step2.     If its not turning Green indicator, you may need to check a Wireless router
     configuration or see the following Website for FAQ.
     http://panasonic.net/pss/security/support/info.html
Ste
p
2
Quick Reference Guide for Setup
5. Setup is completed. For the operation, please refer to O/I in the CD-ROM.     If the setup does not complete successfully, please see the following Website for FAQ.
     http://panasonic.net/pss/security/support/info.html                       Connection
Ste
p
1
6
4. If your router has a WPS
*1 function, press the button on the back
    of the wireless router.
     
If NO WPS function on your router, please connect the LAN cable as the
     Wired Connection. (For detail information, refer to the operating instructions
     of the wireless router)
Wireless Indicator
(WPS indicator )Power Indicator
BL-VT164W
BL-VP104W
1
2
35
WPS Button4
Route
r
Internet ModemLAN cable
(Cat-5 straight cable)
To the Power OutletWireless Button
(WPS Button)*1AC adapto
r
PC
*1: WPS(Wi-Fi Protected Setup) is a computing standard that attempts to allow
      easy establishment of a secure wireless home network.
Setup Will Not Work On A Mac
® 
						

							cam9014727
                                     Access from a mobile terminal1. Click the [Setup] button.
2. Click the [Internet] button on the Setup Menu.
3. Select [On] for  [UPnP(Auto port forwarding)].
6. When the Viewnetcam Page is displayed, click [New Registration] to
    register your information for the “Viewnetcam.com” service.
7. The registration is proceeded, Domain name shows up on the display.
    Please write down the Domain Name for accessing to viewnetcam later.
    The domain name will be enable in 30 minutes.
1
23
4
4. Select [Viewnetcam.com] for [DDNS], then click [Set].
5
5. When [UPnP (Auto port forwarding) setup is complete.] is displayed,
    click [Go to Viewnetcam.com Registration page].Ste
p
3 if re
q
uired
9. For detail information, please see the Installation Guide or Operating Instruction in the CD-ROM.
Exam
ple
The global IP address shown is temporary because it will
most likely change as soon as the router is restarted.
For a permanent link to the camera, please use the
viewnetcam URL found in [Status] –[Viewnetcam] in the
[Maintenance] section. Remember to add the tags after
the URL if you are using a mobile device.
Example of URL to access the camera from different devices:
   PC: http://cam9014727.viewnetcam.com:50006
   Mobile: http://cam9014727.viewnetcam.com:50006/mobile
           
     http://cam9014727.viewnetcam.com:50006/cam
Exam
ple6
87
If the UPnP (Auto Port forwarding) setup fails, the router
may not have UPnP enabled (It is disabled by default in
most routers).
In this case, manual port forwarding will be required.
Refer to router’s operating instructions for assistance.
For more information, refer to the operating instructions
of your router. Or see the Website for FAQ.
http://panasonic.net/pss/security/support/info.html
8. When the registration of the Viewnetcam service is complete, the global
    IP address of the camera is dis
played in the 
[Setu
p Com
plete
] window.
PGQW1274ZA
avs1012-0/1
Printed in China