Home
>
Panasonic
>
Projection Television
>
Panasonic Multimedia Projection Hdtv Pt 44lcx65 Operating Instructions
Panasonic Multimedia Projection Hdtv Pt 44lcx65 Operating Instructions
Have a look at the manual Panasonic Multimedia Projection Hdtv Pt 44lcx65 Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
21 Getting Start edRGB signals that can be input The table below lists the different types of RGB signals that can be input. If a signal which differs greatly from the types listed below is input, the picture may not be displayed correctly, or a black background may be displayed. In this case, “signal” will flash on-screen for about 5 seconds. Notes: • Input signals, other than those listed with a * mark, will give you a beautiful, stable picture. • The D-SUB15P connector can accept RGB (H-V sync separate). • When an external video processor/scaler is used, it must have RGB (H-V sync separate) output. Mode typeSignal data Information menu display No. of dots (H × V)Horizontal frequency (kHz)Vertical frequency (Hz) Personal Computer Signals VGA400 (70 Hz) 640 × 400 31.47 70.08 VGA400 VGA480 (60 Hz) 640 × 480 31.47 59.94 VGA480 SVGA (60 Hz) 800 × 600 37.88 60.32 SVGA * XGA (60 Hz) 1 024 × 768 48.36 60.00 XGA
For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo22 How to connect the HDMI input terminal HDMI is the first all digital consumer electronics A/V interface that supports several uncompressed standard, enhanced and high definition video format as well as all existing multi-channel audio formats. One jack supports both video and audio information. The HDMI/HDCP* 1 input can be connected to an EIA/CEA 861/861B*2 compliant consumer electronic device, such as a set top box or DVD player equipped with a HDMI output connection. By inputting a High-bandwidth Digital Content Protection (HDCP) high definition picture source to the HDMI terminal of this unit, high definition pictures can be displayed on the screen in their digital form. The HDMI input terminal is not intended to be used with personal computers. This unit is compatible with 1080i, 720p, 480p and 480i formats. Select the output of the connected device to match that of the unit. Notes: *1 HDMI/HDCP = High Definition Multimedia Interface / High-Bandwidth Digital Copy Protection.*2 EIA/CEA-861/861B Profiles compliance covers profiles for transmission of uncompressed digital video including high bandwidth digital content protection. Follow the diagram below to connect the unit to a set top box or a DVD player. About HDMI Connection diagram Installation (continued) AUDIO OUTHDMI OUT HDMI OUT The connector on the unit is HDMI Type A connector. The connector on the unit is HDMI Type A connector. Set top box Set top box When audio signal input is digital. When audio signal input is analog. For models PT-52LCX35/PT-61LCX35 : • Similar connections are available at the HDMI Input 1-2 Terminals. (P. 11) For models PT-52LCX35/PT-61LCX35 : • Similar connections are available at the HDMI Input 1-2 Terminals. (P. 11) • When AV IN 1 connection is used, connect to AUDIO IN 1. Likewise, if AV 2 connection is used, connect to AUDIO IN 2. (PT-44LCX65/ PT-52LCX65/ PT-61LCX65)(PT-52LCX35/ PT-61LCX35)
23 Getting Start ed By inputting a High-bandwidth Digital Content Protection high-definition picture source to the HDMI IN terminals of this Projection Display, high-definition pictures can be displayed on the screen in their digital form. (This terminal is for use in the future when High-bandwidth Digital Content Protection DVD players and D-VHS are put on the market.) Notes: • Select the HDMI input position by pressing the TV/VIDEO button. (P. 32) • The HDMI IN terminals can only be used with 1080i, 720p, 480p and 480i picture signals. • If there is no audio, check if the source equipment has PCM output. If not, please use analog connections. • Be sure HDMI is securely connected. If not, picture noise and/or incorrect picture display may result. • With HDMI connection, depending on the signal, the picture may be displayed with unnatural colors (as if red and blue are reversed). Refer to “Color Corr.” on page 41. • If the external device has only a DVI output, connect to the HDMI terminal via a DVI to HDMI adaptor cable* 1. • When the DVI to HDMI adaptor cable*1 is used, connect the audio cable to the audio input terminal. Procedure When digital audio is included in the HDMI connection, the compatible sampling frequencies are 48 kHz/44.1 kHz/ 32 kHz. Refer to “HDMI In” on page 43. Video Signal: The Projection Display is compatible with following formats. Please set the connecting device to following format. Display mode No. of dotsVertical scanning frequency (Hz)Information menu display 1080i 1920 × 1080 59.94 / 60 1080i 720p 1280 × 720 59.94 / 60 720p 480p720 × 480 640 × 48059.94 / 60 59.94 / 60480p 480i 720 × 480 59.94 / 60 480i • If you cannot display the picture because your Digital Set Top Box does not have a Digital Out terminal setting, use the Component Video Input (or the S-Video Input or Video Input). In this case, the picture will be displayed as an analog signal. 2 Press TV/VIDEO to select HDMI input. 1 Connect the HDMI output from the set top box or a DVD player to the HDMI input on the back of the unit. Compatible formats Audio signal ( PCM) *1 Enquire at your local digital device retailer shop.
For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo24 POWER SAP LIGHT MENU 123 45 6 78 09 RETURN CH CH VOL VOL R-TUNE REW TV/VCRSPLIT SWAP DVD/VCR CH OPEN/CLOSE PLAY PA U S E S T O P R E CFF PROG TV/VIDEOSLEEP EXIT TV VCR DVD DTV RCVR DBS/CBLAUX OK MUTE ASPECT FAVORITE RECALL Always be sure to follow the procedure given below to turn the Projection Display power ON and OFF. • The lamp cooling fan will continue to operate for approximately 1 minute after the power is turned off. During this time, the POWER indicator will blink Red. Press POWER on Projection Display or Remote Control to turn power on. The Power Indicator blinks Green for about 20 seconds and then turns solid Green.The Power Indicator Notes: • If the POWER button is accidentally turned off during use, after power is turned back on, it may take a short period before the lamp automatically comes on. • After the unit is turned on, maximum picture brightness will be achieved in 5-10 minutes. This is normal. • This unit consumes approx. 0.3 W (15W when CableCARD™ is inserted.) in OFF condition when plugged into an AC outlet. Press POWER on Projection Display or Remote Control to turn power off. Note: • When the power cord is disconnected, the internal cooling fan stops op er at ing. In this case, the lamp will be insufficiently cooled and will take a while to turn ON again. Power ON Power OFF The Power Indicator blinks Red for about 1 minute and then LED turns off. Turning the Power ON and OFF LED ACTION Off Power – OFF Red (blinking) Power – OFF (Now cooling) Green Power – ON Green (blinking)Power – ON (Preparing to light lamp) Power shuts off after a Black Screen is displayed for a few seconds. Note: • If the POWER button is pressed during the Black Screen display, Power is turned back on. Do not disconnect the power cord from the outlet and do not open the circuit breaker (unless necessary) while the cooling fan is still operating. Do not disconnect the power cord from the power outlet while the power indicator blinks Red. POWER Power ON / OFF Auto shut off To extend lamp life, if there is no signal to the set’s tuner for 5 minutes, the lamp will shut off automatically. POWER button/ POWER indicator URETURN CH CH VOLVOLOK NUNUN
25 Basic Operation For your convenience, First Time Set up menu will be displayed on screen when the set is turned on for the first time. If needed, follow the menus and procedures displayed on-screen for setting up the features. Auto program You can scan All (Analog and Digital) channels. If needed, follow the menus and procedures displayed on-screen for setting up the features. You can also make the settings in Setup menu. Notes: • After “Auto program” is completed the unit tunes to the first channel found during “Auto program”. • If setup is incomplete, check connection of Antenna/Cable to the RF IN Terminal, then try “Auto program” again. ( p. 29). • “Auto program” must be done when you select the input signal for the first time or whenever you change the antenna configuration. • Depending on conditions, “Auto program” may take a while. First Time Setup Language The language of the on-screen display is set to English as the factory setting. You can select English, Spanish or French as the on-screen displays language. Press to select “Language”. First time setup Language Auto program Language Language ◄English► Press to display Language screen. 1 CH CH VOL VOL OK CH CH VOL VOL OK Press to select “English,” “Español” or “Français”. 2 3 Press to go to previous screen. Or, select icon, then press OK for same results. Auto program ANT In ◄ Cable ► Mode All Start scan Press to select “ANT In”. Press to select “Cable” or “Antenna”.2 CH CH VOL VOL OK Press to select Mode. Press to select “All” or “ Analog”. 3 Auto program ANT In Cable Mode ◄ All ► Start scan CH CH VOL VOL OK CH CH VOL VOL OK 4Press to select “Start scan”. Press to start. Channels available for reception will be set automatically. Auto program ANT In Cable Mode All Start scan Now scanning analog channel ... Progress 5 RETURN After Auto Program is complete, the unit will return to Manual Program mode. To place the channels that were located by auto scan in memory, move the cursor to “Apply” and press OK. (pp. 30-31). If OK is not pressed after selecting OK, the channels will not be memorized. First time setup Language Auto program Press to select “Auto program”. Press to display Auto program screen.1CH CH VOL VOL OK
For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo26 POWER SAP LIGHT MENU 123 45 6 78 09 RETURN CH CH VOL VOL R-TUNE REW TV/VCRSPLIT SWAP DVD/VCR CH OPEN/CLOSE PLAY PA U S E S T O P R E CFF PROG TV/VIDEOSLEEP EXIT TV VCR DVD DTV RCVR DBS/CBLAUX OK MUTE ASPECT FAVORITE RECALL Pressing MENU displays the Main Menu screen. Press to select the desired icon. Press to return to previous level menu. PressEXITMENU RETURN Press to display Main menu. Picture Audio Timer Lock Memory Card Setup Picture Color Temp Normal PC Adjust Other Adjust Adv. Adjust Example: If RETURN is pressed from Adv. Adjust Menu: Adv. Adjust Normal No Gamma Adj. Full Blk. Extension +10 R Level +10 G Level +10 B Level +10 Picture Audio Timer Lock Memory Card Setup Button operation during Menu display (Menu navigation) to exit menu. Basic Menu Navigation Example of a procedure Depending on the signal being input, some items may or may not be adjustable and some functions may or may not be available. Note: • While Main Menu (only) is displayed, pressing MENU will exit the menu screen. MENU Picture Audio Timer Lock Memory Card Setup
27 Basic Operation Picture Normal No Pic. Mode Vivid Picture +10 Brightness +10 Color +10 Tint +10 Sharpness +10 Picture Normal No Pic. Mode Vivid Picture +10 Brightness +10 Color +10 Tint +10 Sharpness +10 Press to enter the menu. Press to select desired menu item. Press to adjust or set desired menu item. Other Adjust sub-menu. Press to select Other Adjust. Press to access Other Adjust sub-menu. Press to select desired sub-menu items. Press to adjust or set desired menu item. Color +5 Sub Menu FieldNext Icon Other Adjust Video NR On 3D Y/C Filter On Color Matrix SD MPEG NR On Black Level Light 3D I/P On Color Corr. On Other Adjust Video NR On 3D Y/C Filter On Color Matrix SD MPEG NR On Black Level Light 3D I/P On Color Corr. On Other Adjust Video NR On 3D Y/C Filter On Color Matrix SD MPEG NR Off Black Level Light 3D I/P On Color Corr. On Picture Color Temp Normal PC Adjust Other Adjust Adv. Adjust Picture Color Temp Normal PC Adjust Other Adjust Adv. Adjust A Next Icon means there are more menu items to view. CH CH VOL VOL OK CH CH VOL VOL OK CH CH VOL VOL OK CH CH VOL VOL OK CH CH VOL VOL OK CH CH VOL VOL OK CH CH VOL VOL OK 2 3 45 6 7 8
For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo28 POWER SAP LIGHT MENU 123 45 6 78 09 RETURN CH CH VOL VOL R-TUNE REW TV/VCRSPLIT SWAP DVD/VCR CH OPEN/CLOSE PLAY PA U S E S T O P R E CFF PROG TV/VIDEOSLEEP EXIT TV VCR DVD DTV RCVR DBS/CBLAUX OK MUTE ASPECT FAVORITE RECALL Tuning channels Switching languages for display Allows you to select the language used for On Screen Displays. Press MENU to display the Main Menu screen. Press to select “Setup” icon. Press to display the Setup menu. 1 Picture Audio Timer Lock Memory Card Setup CH CH VOL VOL OK Setup CH scan All Language Program channel Input labels CC Other adjust Language Language ◄English► Press to select “Language”. Press to display Language screen.2CH CH VOL VOL OK CH CH VOL VOL OK3 Press to select “English,” “Español” or “Français”. 4 RETURNPress to go to previous screen. Or, select icon, then press OK for same results. MENURETURN CH CH VOLVOLOK
29 Basic Operation Automatically searches and adds receivable channels to memory. Press MENU to display the Main Menu screen. Press to select “Setup” icon. Press to display the Setup menu. Press to display the Program channel menu. Press to select “Program channel”. Press to select “Auto”. 1 Automatic program setting 2 3 Press to enter the Auto menu.Notes:• If “Cable” or “Antenna” is selected and a CableCARDTM is not inserted, Auto program will perform Scan All. • If “Cable” is selected and a CableCARD™ is inserted, Auto scan will not be available. • Some channels with very weak signals may be locked into memory. If desired, these channels can be deleted man u al ly using the “Manual program setting”. (p. 30) • “Auto program” must be done when you select the input signal for the first time or whenever you change the antenna configuration. Press to select “ANT In”.4 Press to select “Antenna” or “Cable”. Press to select “Mode”.5 Press to select “All” or “Analog”. Press to start Scan. Press to select “ Start scan”.6 Picture Audio Timer Lock Memory Card Setup Now scanning analog channel ... Progress CH CH VOL VOL OK CH CH VOL VOL OK CH CH VOL VOL OK CH CH VOL VOL OK CH CH VOL VOL OK Setup CH scan All Language Program channel Input labels CC Other adjust Program channel Auto Manual Signal meter Auto program ANT In ◄ Cable ► Mode All Start scan Auto program ANT In Cable Mode ◄ All ► Start scan CH CH VOL VOL OK 7 After Auto program is complete, the unit will return to Manual program mode. To place the channels that were located by auto scan in memory, move the cursor to “Apply” and press OK. (pp. 30-31). If OK is not pressed after selecting OK, the channels will not be memorized.
For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo30 Use this procedure when changing setting of receiving channels or changing the channel dis play. Also, use to add or delete channels from channel list manually. Manual program setting Press MENU to display the Main Menu screen. Press to select “Setup” icon. Press to display the Setup menu. Press to select “Manual”. 1 2 3 Press to enter the Manual program screen. Picture Audio Timer Lock Memory Card Setup Program channel Auto Manual Signal meter CH CH VOL VOL OK Press to display the Program channel menu. Press to select “Program channel”. CH CH VOL VOL OK Setup CH scan All Language Program channel Input labels CC Other adjust CH CH VOL VOL OK Edit CH 1 2 3 4 5 6 7 8 9 10- - - - - - - - - - - - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - -No - - - - - - No No No No No No No No No Captio n Favorite AddApply CH CH VOL VOL OKPress to select “Edit”. Press to enter the edit mode. CH CH VOL VOL OKPress to select the desired preset channel line. Press to select edit area. “CH,” “Caption,” “Favorite,” “Add”. 4 5 Tuning channels (continued) Note: • If Lock (p. 45) has been set, you must enter your password to display the Manual Program screen.