Panasonic Multimedia Projection Display Pt 50lc13 Operating Instructions

21
Getting Start ed
RGB/DIGITAL IN signals that can be input
The table below lists the different types of RGB/DIGITAL IN signals that can be input.
If a signal which differs greatly from any of the types listed below is input, the picture image may not be 
dis played correctly, or a black background may be displayed. At this time, “signal” will fl 
ash in the 
on-screen display for about 5 seconds.
Notes:
•   Input signals, other than those listed with a * mark, will give you a beautiful, stable picture....

22For assistance, please call : 1-888-VIEW PTV(843-9788)
Press the  POWER button to turn the 
projection display on.
(Refer to page 23 for “Turning the Power 
ON and OFF”.)
Automatic Channel Setting is performed. First, check the connection of the Plug to the Wall Outlet and the Antenna /Cable to the RF in Terminal.
(PP. 12-14.)
If using Cable Box, DSS Receiver, or VCR,
•   Turn on Cable Box.
•   Turn off DSS Receiver, or VCR.
 Case 1
 Case 2When setup is complete, the lowest 
channel picture appears.
If...

23
Basic Operation
Always be sure to follow the procedure given below to turn the projection display power ON and OFF.
•   The lamp cooling fan will continue to operate for approximately 1 minute after the power is turned off. At the same time, the 
POWER indicator will blink Red.
Press POWER on projection display or remote control to 
turn power on.
The Power Indicator blinks Green for about 10 seconds 
and then turns solid Green.
The Power Indicator
Notes:
•   If the POWER button is accidentally turned...

24For assistance, please call : 1-888-VIEW PTV(843-9788)
2
  Use the ▲, ▼ buttons to 
select an item.   Select MENU desired by 
pushing Left “◄” button 
or Right “► 
” button.
Use the ACTION button 
to set or go to next menu 
screen. 
Pressing the  ACTION 
button displays the 
MENU screen.
Note:
Depending on the signal 
being input, some items may 
or may not be adjustable 
and some functions may or 
may not be available.
1
Flow Chart of Main menu
 ADJUST  SET UP
    PICTURE
    AUDIO
    POSITION/SIZE...

25
Basic Operation
  Returning to the previous screen
If RECALL is pressed while a menu screen is 
displayed, the display will return to the 
previous screen. Adjust items
Set an item
INFORMATION screen
P.  61
LANGUAGE selection screen
P.  61
CAPTION menu VIDEO menu
PP. 56-59
PP. 52-53CHANNEL menu
PP. 26-29, 54-55
POSITION/SIZE ADJUST menu
PP. 48-51 LOCK selection screen PP. 42-43 AUDIO ADJUST menu
PP. 44-45 PICTURE ADJUST menu
PP. 46-47
Select an item
Flow Chart of Main menu
        PICTURE
 PICTURE...

26For assistance, please call : 1-888-VIEW PTV(843-9788)
Automatically searches and adds receivable channels to memory.
Press the ACTION button to display the MENU screen and select SET 
UP.
Press to select 
CHANNEL.
Press to display 
the CHANNEL.
Press to select 
TV or CABLE.Press to select 
ANTENNA.
Press to select 
AUTO SET.
Press to run 
AUTO SET.
Note:
TV or Cable Tuning mode must be set according to your connections.
1
2
3
Channels will automatically advance until all channels have been 
scanned....

27
Basic Operation
Notes:
•   After AUTO SET is fi 
nished, the lowest channel number added will be received.
•   Some channels with very weak signals may be locked into memory. If desired, these channels can be deleted man u al ly using 
the MANUAL SET feature.
4
 Case 1
 Case 2When setup is complete, the lowest channel picture 
appears.
If setup is incomplete, the screen at right appears. Check 
connection of Antenna/Cable to the RF in Terminal, then try 
Automatic Channel Setting again.
Press to exit...

28For assistance, please call : 1-888-VIEW PTV(843-9788)
Use this setting when changing setting of receiving channels or changing the channel dis play.
3
Press to select 
MANUAL SET.
Press to display 
the MANUAL SET 
screen. Press the ACTION button to display the MENU screen and select SET 
UP.
Press to select 
CHANNEL.
Press to display 
the CHANNEL.
Press to select 
TV or CABLE.Press to select 
ANTENNA.
1
2
Manual channel setting
Continued on the next page.
 ADJUST  SET UP
    LANGUAGE :ENGLISH...

29
Basic Operation
4
Press to select channel.
Repeat steps 4 to continue adding or deleting channels.Press to add channels to memory.
Press to select channel.
Press to delete channels from memory.
Press to exit menu.
Note:
Some channels with very weak signals may be locked into memory. If desired, these channels can be deleted manually using the 
MANUAL SET feature.
5
6
To add channel
To delete channel
Tu n i n g  c h a n n e l s  
       MANUAL SET
 ENTER CHANNEL :  01
 CHOOSE A CHANNEL
 USING CHANNEL...

30For assistance, please call : 1-888-VIEW PTV(843-9788)
Operation can be done from the projection 
display.
Press to 
select the 
desired 
volume 
level. Press to select 
the desired 
channel. (Or use 
number keys ) Press to turn the projection display on. Press to operate the projection 
display with the remote control.
1
2
3
4
Notes:
•   The channel number and volume level are stored even after the projection display is turned off.
•   Power consumption can be reduced if the volume level is lowered....