Panasonic Multi Hybrid Control Panel Aw Rp555n Operating Instructions

21

 
4.  Set the left end position in the travel range.
    Operate the PAN/TILT lever to rotate the camera to 
the position which is to serve as the left end position.
    Press the PRESET 1 and 6 buttons while holding 
down the MEMORY button.
    When the button 5 lamp lights, the setting is 
completed.
   To cancel the setting, press the PRESET 1 and 6 
buttons again while holding down the MEMORY 
button. When the setting is canceled, the button 10 
lamp lights.
5.  Set the right end position in...

22

1.   Select the pan/tilt head system using the CONTROL 
button.
2.   Shoot a white object (such as a white wall or 
handkerchief) to fill the whole screen using the pan/tilt 
head system currently selected.
 
Do not allow shiny, reflective or very bright objects to 
appear on the screen.
3.   Press the WHITE BAL A button, and press the AWC 
button. The AWC button’s lamp flashes, and the white 
balance is automatically adjusted. Once the adjustment 
has been performed correctly, the lamp goes off,...

23

1.   Select the pan/tilt head system using the CONTROL 
button.
2.   Press the IRIS button to set the currently selected pan/tilt 
head system to the AUTO mode (the IRIS button’s lamp 
now comes on).
3.   Press the ABC button. 
The ABC button’s lamp flashes, the lens iris is 
automatically stopped down, and the black balance 
is automatically adjusted. Once the adjustment has 
been performed correctly, the lamp goes off, and the 
conditions set are entered in the memory.
   The ABC button’s lamp...

24

1.   Select the pan/tilt head system using the CONTROL 
button.
2.   Use the following buttons to establish the modes.
    Press the IRIS button to establish the MANU mode 
(the IRIS button’s lamp now goes off). 
If the AUTO mode is established, the lens iris position 
will not be entered.
3.   Operate the ZOOM lever and PAN/TILT lever, and on the 
monitor check the pictures which are to be shot.
4.   Select the white balance from among the A, B and ATW 
buttons, and adjust the lens iris using the...

25

Setting procedure
1.   Keep pressing the MENU/ button for two seconds.
   The menu mode is established, and the on-screen 
menus of the camera in the pan/tilt head system 
currently selected are displayed. At this point, the  
MENU/ button lamp remains lighted.
   If the MENU/ button is held down for at least two 
seconds while the MENU/ button lamp is lighted, the 
menu mode is exited, and the on-screen menus can be 
closed.
2.   When the unit is in MENU mode, the MENU/ button, 
ITEM/ button, YES/...

26

Attaching the rack mounting adapters
Replacement of consumable parts
  To install this unit in a rack, use the rack mounting adapters, join-up fixture and mounting screws (M48 mm) supplied.
  Use only the mounting screws provided — do not use any other screws.
 Joystick replacement
The joystick is a consumable part.
Replace the joystick if operation is impeded.
Refer replacement of the joystick to qualified service personnel.
MENUITEMYESDEF(AF)EXTNDLAMPUPLEFTDOWN
NEAR
WIDE
RIGHT
OPWIPH/FNO...

27

How to change the position of the connector panel
TALLY5TALLY3TALLY1TALLY2TALLY4TALLY GND
R543 21/EXTS
TALLY IN
REMOTE/SERVICE
TO PAN/TILT HEADMONITOR SELECT
DC12V INGND
TALLY5TALLY3TALLY1TALLY2TALLY4TALLY GND
R5 43 21/EXTS
TALLY IN
REMOTE/SERVICE
TO PAN/TILT HEADMONITOR SELECT
DC12V INGND
Screws × 4 (bottom panel)
Screws × 4 (rear panel)
Screws × 4 (bottom panel)
Screws × 4 (rear panel)
Connector panel
Remove the connector panel.
Remove the blank panel.
Blank panel
Remove the two rubber feet.
The...

28

TALLY5TALLY3TALLY1TALLY2TALLY4TALLY GNDR
543 2
1/EXT
S
TALLY IN
REMOTE/SERVICE
TO PAN/TILT HEAD
MONITOR SELECT
DC12V IN
GND1LEVEL
IRIS
OPERATE
CA
M
CONT
2 3
4 ATW
ITEMDEF
WIP
H/F
(AF)EXTLAMP
ND
OP
SCENE FILEPRESET
MENU
YES
NO
BA
SHUTTERMOD
E
GAIN
5
2
ON
OFF ON
OFF
3 4
5
ABC
MEMOR
Y
MENUMulti Hybrid Control Panel AW-RP55
5
AWCOKNG
WHT BAL
321USER
TALLYCONTRO
L
HIGHLOW
TELE
WIDE FAR
LEFT
RIGHT
UPDOWN
NEAR
MANUAUTO
SPEE
D
ZOO
M
FOCU
S
PAN/TILT
1 2
3 4
5
6 7 8 910
MANU AUTO0dBLHCAMBAR

8-1/4 (210)...

29

Power supply: DC 10.8 V to DC 16 V
Power consumption: 9.0 W
General
Ambient operating temperature
  14°F to 122°F (–10°C to +50°C)
Storage temperature
  –4°F to +140°F (–20°C to +60°C)
Ambient operating humidity
  30% to 90% (no condensation)
Weight
  3.1 lbs. (1.4 kg)
Dimensions (WHD)
   8-1/4”6-15/16”2-5/16” (21017758 mm) 
(excluding protrusions)
Finish
  AV ivory paint (color resembling Munsell 7.9Y 6.8/0.8)
Pan/tilt heads supported
   AW-PH300, AW-PH300A, AW-PH350, AW-PH360,  
AW-PH500,...

PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANYUNIT COMPANY OF PANASONIC CORPORATION OF NORTH AMERICA
Executive Office:One Panasonic Way 4E-7, Secaucus, NJ 07094   (201) 348-7000
EASTERN ZONE: One Panasonic Way 4E-7, Secaucus, NJ 07094   (201) 348-7621   Southeast Region:   1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024   (770) 338-6835   Central Region:   1707 N Randall Road E1-C-1, Elgin, IL 60123   (847) 468-5200
WESTERN ZONE: 3330 Cahuenga Blvd W., Los Angeles, CA 90068   (323) 436-3500...