Panasonic Multi Format Digital Hd Video Cassette Recorder Ajhd3700b Hdw Operating Instructions

– 41–
Audio split editing
OUT point preview
∫Previewing the automatic insert editing OUT point (when audio split is OFF)
This flowchart shows the operation to preview the automatic insert editing OUT point.
The OUT point for automatic assemble editing can not be previewed.
1. Press the INSERT button to display the INSERT AUTO EDIT menu.
2. Use the automatic insert editing flowchart as a reference and register the VIDEO OUT
point.
3. Press the EXECUTE and the PREVIEW/REVIEW button together to preview the...

– 42–
Variable memory Function
1. Set the F3 (W/PLYR) key to OFF.
2. Set the F4 (VAR MEMO) key to ON.
≥If the IN and OUT points have already been entered, they will be automatically cleared.
≥If the split mode is ON, it will be forcibly turned off.
≥When the variable memory function is used, the AUDIO IN and OUT points cannot be 
entered.
3. Input the unit’s edit IN point.
The variable memory playback will start at this point.
≥There is no need to set the OUT point for variable memory playback.
4. Set...

– 43–
Variable memory function
By operating the VTR search dial which is connected to the unit’s RS-422A REMOTE OUT or REMOTE
IN/OUT connector, the playback speeds and directions can be stored in the memory, after which the stored
contents can be regenerated during automatic editing and stored in the memory of the unit (recorder).
1. Set the F3 (W/PLYR) key to ON.
∫To operate the VTR connected to the REMOTE OUT connector by remote control, set
F5 (PLYR SEL) on the ASSEMBLE/INSERT AUTO EDIT menu to...

– 44–
Connector signals
∑VIDEO IN
HD SDI (DIGITAL) BNCk2, active through
SD SDI IN (DIGITAL) BNCk2, active through
SD SDI SPARE BNCk1
HD REF IN BNCk2, loop-through with 75≠termination switch
SD REF IN BNCk2, loop-through with 75≠termination switch
∑VIDEO OUT
HD SDI OUT (DIGITAL) BNCk3
HD SDI MONITOR OUT  BNCk1
(DIGITAL) (SUPER)
SD SDI OUT (DIGITAL) BNCk2
SD SDI MONITOR  BNCk1
(DIGITAL) (SUPER)
VIDEO OUT (ANALOG) BNCk3
HD REF OUT BNCk1
SD REF OUT BNCk1
WFM BNCk1, Waveform output, 75≠.
∑TIME CODE
TIME CODE...

– 45–
Connector signals
∑PARALLEL I/O (50P) connector
(1)PULSE SIGNAL:The signal fall is detected and the signal becomes active.
Pin no.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal
REC COMMAND
PLAY COMMAND
FF COMMAND
REW COMMAND
STOP COMMAND
STBY ON
COMMAND
STBY OFF
COMMAND
RS-422 REMOTE
ON COMMAND
RS-422 REMOTE
OFF COMMAND
LOCAL ENABLE
COMMAND
EJECT COMMAND
ENTRY
COMMAND
ALL_REC_INH_
ON COMMAND
PRE_CTL_INH_
ON COMMAND
LOCAL DISABLE
COMMAND
Direction
INPUT
INPUT
INPUT
INPUT
INPUT
INPUT
INPUT
INPUT
INPUT...

– 46 –
Connector signals
Pin no.
16
17
18
19
20
21
22
23
24
25
26
27
28
Signal
TC_SOURCE_
EXT COMMAND
TC_SLAVE_AUTO
COMMAND
TL_SLAVE_MUST
COMMAND
TC_RESET
COMMAND
STBY ON/OFF
COMMAND
ERR O STATUS
SPARE
CUE COMMAND
ERR 1 STATUS
SPARE
i15 V POWER
REC STATUS
PLAY STATUS
Direction
INPUT
INPUT
INPUT
INPUT
INPUT
OUTPUT
INPUT
INPUT
OUTPUT
INPUT
OUTPUT
OUTPUT
OUTPUT
Type
PULSE SIGNAL
PULSE SIGNAL
PULSE SIGNAL
PULSE SIGNAL
PULSE SIGNAL
SIGNAL
PULSE SIGNAL
SIGNAL
ACTIVE_L
ACTIVE_L
Description
This sets TC SOURCE...

– 47 –
Description
This becomes active when the VTR is in the FF mode.  
This becomes active when the VTR is in the REW mode.  
This becomes active when the VTR is in the STOP mode.  
This becomes active when the RS-422 REMOTE status is
ON.
This becomes active when a cassette tape has not been
inserted.  
Refer to the 50P error status output table on the previous
page. (This pin is related with pins 21 and 24.)
11: INT 10: EXT_LTC
01:  S_VITC (EXT VITC) 00: S_LTC [Pin 36, pin 35]
[Pin 38, pin 37] TC...

– 48 –
Connector signals
∑RS-422A REMOTE
Pin No.
1
2
3
4
5
Pin No.
6
7
8
9
Signal
FRAME GROUND
REM IN (j) LINE(j)
REM OUT (j) STATUS LINE (i)
GND
––––––
Signal
GND
REM IN (j) CMD LINE (j)
REM OUT (j) STATUS LINE (i)
FRAME GROUND
Pin No.
1
2
3
4
5
6
Pin No.
7
8
9–19
20
21–25
Signal
FRAME GROUND
TX Send data
RX Receive data
RTS Request to send
CTS Clear to send
DSR Data set ready
Signal
GND Signal ground
DCR Receive carrier detect
––––––
DTR Data terminal ready
––––––
∑RS-232C REMOTE
∑V/A CONTROL
Pin No....

– 49 –
Video head cleaning
Although this unit comes with an auto head cleaning function which reduces the amount of dirt on the heads,
it is recommended that the video heads be cleanid every day for even more dependable operation. (For fur-
ther details, please consult with your local dealer.)
∑Operation
Remove the cover of the upper portion on the cylinder. Soak some alcohol in a cleaning cloth,
press it lightly against hte middle drum as shown in the figure, and rotate the drum 2 or 3 times
in the...

– 50 –
Rack-mounting
The VTR can be installed in a 19-inch standard rack using the AJ-MA37P rack-mounting adapters (optional
accessory).
It is recommended that the slide rail (CC3001-99-0191) made by Chassis Trak be used as the installed rails.
For further details, consult your dealer.
1. Attach the inner members on each side of the VTR using the four screws supplied with the
slide rails .
The length of the screws used is limited.
If the mounting screws have been lost or misplaced, use screws with a...