Panasonic Monitor Bt Ls1400 Owners Manual

Before attempting to connect, operate or adjust this product, please read these instructions completely.
BT-LS1400P
Liquid Crystal Video Monitor
POWER
INPUT SCAN BLUEMENU/
EXITENTER
M ENU VOLUME
Printed in Japan
VQT0F29 

2
indicates safety information.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, 
DO NOT REMOVE COVER (OR  BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to...

3
indicates safety information.
CAUTION:
THE SOCKET-OUTLET SHALL BE
INSTALLED NEAR THE EQUIPMENT AND
SHALL BE EASILY ACCESSIBLE. 
∫
THIS APPARATUS MUST BE GROUNDED
To ensure safe operation the three-pin plug must be
inserted only into a standard three-pin power outlet
which is effectively grounded through normal house-
hold wiring.
Extension cords used with the equipment must be
three-core and be correctly wired to provide connec-
tion to the ground. Incorrectly wired extension cords
can be extremely...

4
This product has been specially designed for commercial use.  As such, it should be used and operated
only by persons with related expertise.
¥ ¥
The liquid crystal parts are fabricated using high-precision technology.  The screen has effective
pixels that cover more than 99.99% of its area, but pixels may be missing or remain permanently
lighted (red, blue and/or green) in less than 0.01% of the area.  This is not indicative of malfunctioning.
¥ ¥
The LCD panel has been specially finished.
Do not wipe...

5
Power switch
This is the main power switch.
When the power is ON, the LED (green) above the
switch lights.
1
2
INPUT selector button
This is used to select the signal input, and each time it is
pressed, the input is switched in the following sequence:
LINE A >LINE B >CMPNT>SDI >LINE A.

The SDI signal input can be selected only when the BT-
YA210G, available as an optional accessory, is installed.
5
MENU selector buttons
These are used to display the menus and perform the
adjustments and settings....

6
Parts and their functions (rear panel)
REMOTE connector
This 9-pin, D-sub connector is for remote control
purposes.
<
=
SD-SDI connectors (optional)
These are SD-SDI input connectors (BNC) with active
thru output.
>
AC IN power socket
This is the AC power socket.  Connect the accessory
power cord here.
@
Screw hole for cable clamp
This screw hole is for attaching the clamp for the power
cord.  Refer to the following when attaching the clamp.
?
Security lock
This can be used to connect a...

7
How to use the on-screen menus
Press the MENU/EXIT button to display the main menu on
the screen.
PICTURE
This menu is used to perform the settings relating to the
picture.
1
2
VIDEO CONFIG
This menu is used to perform aspect and component
input level settings.
5
[INPUT]
The currently selected signal—whether LINE A, LINE B,
CMPNT or SDI (optional)—is displayed here.
4 3
MAINTENANCE
This menu is used to display the running time of the LCD
monitor.
SYSTEM CONFIG
This menu is used to set the backlight...

8
[PICTURE MENU]
MODE           BROADCAST
CONTRAST              60
BRIGHT                30
CHROMA                30
PHASE                 30
SHARPNESS             30
AI                   OFF
NR                   OFF
COLOR TEMP           D93
3D Y/C               OFF
[LORD FACTORY]
MODE
The video mode is selected here.
≥BROADCAST
This mode is set at the factory to best suit broadcast
operations.
≥GENERAL
This mode applies the dynamic settings which were set
at the factory for generally receiving images....

9
[SYSTEM CONFIG]
BACKLIGHT            60
STATUS DISPLAY CONTINUE
[INPUT SELECT]
LINE B             ON
CMPNT              ON
SDI                ON
REMOTE              OFF
BACKLIGHT
The backlight brightness is adjusted to a value from 0 to 60
here.  60 is the factory setting.
STATUS DISPLAY
The information displays during input switching and input
signal system display are set here.
≥CONTINUE
The information remains displayed.  This is the factory
setting.
≥3 SEC OFF
The information is displayed for 3...

10
REMOTE specifications
Pin No.
1
2
3
4
5
6
7
8
9Signal
Input switching function
Aspect ratio switching function
Standby function
Tally function
GND
s
s
s
s
54321
9876
Connector (9P)
In order to perform REMOTE operations, select ON as the
setting for the REMOTE menu item on the SYSTEM
CONFIG menu.
The functions for REMOTE operations can be switched by
opening or shorting the pins corresponding to the functions
to pin 5 (ground).  There are two kinds of operations: level
operations and edge operations....