Panasonic Monitor Bt Lh900 Owners Manual

							11
How to use the on-screen menus
Four kinds of information—menus, status displays, image control settings and battery voltage—can be displayed on the
screen.
Menu display
This display appears when the MENU/EXIT button is
pressed.  If no further action is taken for the next 120
seconds, the display will be automatically cleared.
The position where the display appears on the screen can
be changed using the marker setting.
For details on the menu, refer to “MAIN MENU” (page 15).
 [MAIN MENU]
  MARKER                4
  VIDEO CONFIG          4
  SYSTEM CONFIG         4
  OSD CONFIG            4
  GPI                   4
  INPUT SELECT          4
  CONTROL               4
     EXIT    SEL    ENTER 1
MENUXWENTER
Status display
The status display information is displayed under the
following conditions while the menu display is not on the
screen.
≥When the input signals have been switched
≥When the input channel has been changed
≥When no signals are supplied
The display location and display time can be changed using
the menu settings.  When images are adjusted using the
image controls while the status display information is on the
screen, the display is cleared, and the settings adjusted by
the controls are displayed instead.
  SDI1 1080/60I
  CRCC
  DC150V       60%
.
1
2
3
1 
Channel and signal format
The channel which has been selected—whether SDI 1,
SDI 2, VIDEO, YPBPR or RGB—is displayed here.
Indicated as the signal format is the format of the signals
which have been input.  However, “UNSUPPORTED
SIGNAL” will appear if signals which are not supported
have been input.
Similarly, “UNSUPPORTED SIGNAL” will also appear if
signals not selected as the FORMAT item setting on the
INPUT SELECT screen of the main menu are input even
when those signals are supported.
For details on the signals supported and format displays,
refer to page 12.2 
Warning display
This appears when an error has occurred or when a
special mode is being used.
CRCC This indicates a CRCC error, and it appears
when the SDI signals contain an error.
FILM This appears when the film mode (FILM) has
been selected as the GAMMA SELECT item
setting on the VIDEO CONFIG screen of the
main menu.
This appears when REMOTE has been
selected as the CONTROL item setting on the
CONTROL screen of the main unit.  The
monitor controls will no longer function at this
time.
3 
Battery voltage display
This indicates the voltage level of the battery.  If an Anton
Bauer digital battery is being used, its remaining level is
indicated as a number of “∫” blocks and as a percentage
along with the voltage value.
#5-)1	725
&OHMJTI
 
 
 
 
 .
 
 
						

							12
How to use the on-screen menus
Battery voltage display
Concerning the signal formats
The battery voltage information is displayed all the time
when ON has been selected as the BATTERY REMAIN
item setting on the OSD screen of the main menu.
It indicates the voltage level of the battery.  If an Anton
Bauer digital battery is being used, its remaining level is
indicated as a number of “∫” blocks and as a percentage
along with the voltage value.
  DC150V       80%.
Image control display
The image control information is displayed when an image
has been adjusted using the image controls.  (Refer to page
6)
It appears when a control has been pressed in so that it has
popped out or when an adjustment is made by turning an
already popped out control.
It is cleared when a control is pressed again and returned to
its original position.  It is also cleared when a popped out
control is not touched for 10 seconds.
 [CONTRAST]        50
Menu setting Signals whose input is accepted Status display
AUTOAll supported signals The format of the input signals is displayed.
1080/50I1080/50I 1080/50I
1080/25P1080/25P 1080/25P
576/50I576/50I576/50I
480/60P480/59.94P480/60P
480/60I480/59.94I480/60I
NTSCNTSCNTSC
PALPALPAL 1080/60I1080/60I
1080/59.94I 1080/59.94I1080/60I
1035/60I1035/60I
1035/59.94I 1035/59.94I1035/60I
1080/30P1080/30P
1080/29.97P 1080/29.97P1080/30P
720/60P720/60P
720/59.94P 720/59.94P720/60P
720/60P ANAMO720/60P
720/59.94P 720/59.94P720/60P
1080/24P1080/24P
1080/23.98P 1080/23.98P1080/24P
1080/24PsF1080/24psF
1080/23.98psF 1080/23.98PsF1080/24PsF
#5-)1	725
&OHMJTI
 
 
 
 
 .
 
 
						

							13
Menu operations
Menu operations
MENU/EXIT button
Use the HD ZOOM/Xbutton and BLUE/Wbutton to
move the cursor, and select the desired menu using the
FUNCTION/ENTER button.
1
2When the MENU/EXIT button is pressed, the main
menu appears on the screen.
 [MAIN]
  MARKER                4
  VIDEO CONFIG          4
  SYSTEM CONFIG         4
  OSD CONFIG            4
  GPI                   4
  INPUT SELECT          4
  CONTROL               4
     EXIT    SEL    ENTER1
MENUXWENTER
Use the HD ZOOM/Xbutton and BLUE/Wbutton to
align the cursor with the item to be changed, and press
the FUNCTION/ENTER button.  The setting is now
displayed in green.3
 [MARKER]
  MARKER SELECT      MENU
  MARKER 16:9         OFF
  MARKER 4:3          OFF
  MARKER BACK      NORMAL
  CENTER MARKER       OFF
  GPI PRESET1         80%
  GPI PRESET2         80%
     EXIT    SEL    ENTER1
MENUENTERXW
Use the HD ZOOM/Xbutton and BLUE/Wbutton to
change the setting, and press the FUNCTION/ENTER
button to enter the change.
Alternatively, the change will be canceled when the
MENU/EXIT button is pressed instead.4
Press the MENU/EXIT button to exit the menu settings.5
 [MARKER]
  MARKER SELECT       GPI
  MARKER 16:9         OFF
  MARKER 4:3          OFF
  MARKER BACK      NORMAL
  CENTER MARKER       OFF
  GPI PRESET1         80%
  GPI PRESET2         80%
     EXIT    SEL    SET1
MENUENTERXW
Displayed in green.
#5-)1	725
&OHMJTI
 
 
 
 
 .
 
 
						

							14
User data
This monitor enables the menu settings and screen values which have been adjusted by the image controls to be saved in
five user data files which can then be loaded as required.
The following data can be saved and loaded as user data files:
≥All menu settings (including the function settings of the buttons at the front of the monitor) with the exception of USER
MODE LOAD/SAVE
≥Screen values which have been adjusted by the image controls
Saving the user data
Using menu operations (see page 13), select USER
MODE SAVE on the SYSTEM CONFIG screen, and
press the FUNCTION/ENTER button.  The setting is
now displayed in green.
1
2When the MENU/EXIT button is pressed, the main
menu appears on the screen.
4Align the cursor with YES, and press the
FUNCTION/ENTER button.
 [SYSTEM CONFIG]
  BACK LIGHT           60
  FUNCTION            WFM
  WFM            FUNCTION
  HD ZOOM           FRONT
  PEAKING PHASE     PHASE
  USER MODE LOAD  FACTORY
  USER MODE SAVE    USER1
     EXIT    SEL    SET
1
MENUENTERXW
When the file whose data is to be saved is selected
from the USER1 to USER5 files and the
FUNCTION/ENTER button is then pressed, the screen
shown below appears.3
 [USER MODE SAVE]
       USER1
           YES
           NO
  
     EXIT    SEL    SET
1
MENUENTERXW
Displayed in green.
Loading the user data
Using menu operations (see page 13), select USER
MODE LOAD on the SYSTEM CONFIG screen, and
press the FUNCTION/ENTER button.  The setting is
now displayed in green.
1
2When the MENU/EXIT button is pressed, the main
menu appears on the screen.
4Align the cursor with YES, and press the
FUNCTION/ENTER button.
 [SYSTEM CONFIG]
  BACK LIGHT           60
  FUNCTION            WFM
  WFM            FUNCTION
  HD ZOOM           FRONT
  PEAKING PHASE     PHASE
  USER MODE LOAD  FACTORY
  USER MODE SAVE    USER1
     EXIT    SEL    SET
1
MENUENTERXW
When the file whose data is to be loaded is selected
from the FACTORY or USER1 to USER5 files and the
FUNCTION/ENTER button is then pressed, the screen
shown below appears.
If FACTORY is selected at this time, the data is restored
to the factory settings.3
 [USER MODE LOAD]
       USER1
           YES
           NO
  
     EXIT    SEL    SET
1
MENUENTERXW
Displayed in green.
#5-)1	725
&OHMJTI
 
 
 
 
 .
 
 
						

							15
MAIN MENU
Menu configuration
MARKER  MARKER SELECT  MARKER 16:9
  MARKER 4:3
  GAMMA SELECT
  SHARPNESS H
  SHARPNESS V
  BATTERY REMAIN
  STATUS DISPLAY
  CRCC MESSAGE  MENU POSITION  STATUS POSITION  ROTARY POSITION
  COLOR TEMP.  SHARPNESS MODE
  CONTROL
  LOCAL ENABLE
  BACKLIGHT TIME
  SD ASPECT   I-P MODE  MONO
  BACKLIGHT
  FUNCTION
  WFM  HD ZOOM  PEAKING/PHASE  USER MODE LOAD
  GPI1
  GPI2
  GPI3  GPI4  GPI5
MAIN
VIDEO CONFIG
SYSTEM CONFIG
  MARKER BACK
  USER MODE SAVE
OSD CONFIG
GPI
INPUT SELECT
CONTROL
  GPI PRESET1
  GPI PRESET2
  GPI6
  GPI7
  GPI8   SDI1
     FORMAT
  SDI2
     FORMAT
  VIDEO
     FORMAT
  YPBPR/RGB
     MODE
        FORMAT
     COMPONENT LEVEL
     RGB SYNC
  CENTER MARKER
  FILM GAMMA
#5-)1	725
&OHMJTI
 
 
 
 
 .
 
 
						

							16
MAIN MENU
The underlined setting indicates the factory setting mode.
Item Setting DescriptionItem Setting Description
MARKER SELECTMENU
GPIFor setting whether the marker display
settings are to be performed using the
menu or from the GPI connector.
MENU: The operations are performed using
the menu.  Operations from the GPI
connector are canceled.
GPI:The operations are performed from
the GPI connector.  The settings
established using the menu are
canceled.
MARKER 16:9OFF
4:3
13:9
14:9
VISTA
CNSCO
95%
93%
90%
88%
80%For selecting the type of marker used for
16:9 images.
OFF:No markers are displayed.
4:3:Markers indicating the 4:3 size are
displayed.
13:9:Markers indicating the 13:9 size are
displayed.
14:9:Markers indicating the 14:9 size are
displayed.
VISTA: Markers in the vista size (1.85:1)
are displayed.
CNSCO:Markers in the cinemascope size
(2.35:1) are displayed.
95%:The 95% area markers are displayed.
93%:The 93% area markers are displayed.
90%:The 90% area markers are displayed.
88%:The 88% area markers are displayed.
80%:The 80% area markers are displayed.

When 4:3 images are displayed, the setting
of this item is not reflected.
GPI PRESET14:3
13:9
14:9
VISTA
CNSCO
95%
93%
90%
88%
80%For setting the markers to be displayed if,
when MARKER1 ON/OFF has been
allocated to any item and GPI has been
selected as the MARKER SELECT item
setting on the GPI screen, the
corresponding pin has been set to ON.
For details, refer to “REMOTE
specifications” (page 22).
4:3:Markers indicating the 4:3 size are
displayed.
13:9:Markers indicating the 13:9 size are
displayed.
14:9:Markers indicating the 14:9 size are
displayed.
VISTA: Markers in the vista size (1.85:1)
are displayed.
CNSCO:Markers in the cinemascope size
(2.35:1) are displayed.
95%:The 95% area markers are displayed.
93%:The 93% area markers are displayed.
90%:The 90% area markers are displayed.
88%:The 88% area markers are displayed.
80%:The 80% area markers are displayed.
GPI PRESET24:3
13:9
14:9
VISTA
CNSCO
95%
93%
90%
88%
80%For setting the markers to be displayed if,
when MARKER2 ON/OFF has been
allocated to any item and GPI has been
selected as the MARKER SELECT item
setting on the GPI screen, the
corresponding pin has been set to ON.
For details, refer to “REMOTE
specifications” (page 22).
4:3:Markers indicating the 4:3 size are
displayed.
13:9:Markers indicating the 13:9 size are
displayed.
14:9:Markers indicating the 14:9 size are
displayed.
VISTA: Markers in the vista size (1.85:1)
are displayed.
CNSCO:Markers in the cinemascope size
(2.35:1) are displayed.
95%:The 95% area markers are displayed.
93%:The 93% area markers are displayed.
90%:The 90% area markers are displayed.
88%:The 88% area markers are displayed.
80%:The 80% area markers are displayed.
MARKER 4:3OFF
95%
93%
90%
88%
80%For selecting the type of marker used for
4:3 images.
OFF:No markers are displayed.
95%:The 95% area markers are displayed.
93%:The 93% area markers are displayed.
90%:The 90% area markers are displayed.
88%:The 88% area markers are displayed.
80%:The 80% area markers are displayed.

When 16:9 images are displayed, the
setting of this item is not reflected.
MARKER BACKNORMALHALF
BLACKFor setting the background brightness of
the markers.
NORMAL:The background is set to the
normal brightness.
HALF:The background brightness is set
to 50%.
BLACK:The background brightness is set
to 0%.

The setting of this item is valid only when
4:3, 13:9 or 14:9 has been selected as the
MARKER 16:9 item setting.
CENTER MARKEROFF
ONFor selecting whether to display the center
marker.
OFF:The center marker is not displayed.
ON:The center marker is displayed.
Menu items
MARKER
#5-)1	725
&OHMJTI
 
 
 
 
 .
 
 
						

							17
MAIN MENU
Types of markers
4:3 markers 13:9 markers
14:9 markers
95% area markers 93% area markers
90% area markers
80% area markers
95% area markers 93% area markers
90% area markers88% area markers
80% area markers
4:3 markers
(These appear when SD signals with a 4:3
aspect ratio are supplied.)
Dotted lines are displayed as the markers.
Center marker
Center marker
This appears at the center of the image.
16:9 markers
(These appear when HD signals or when SD
signals with a 16:9 aspect ratio are supplied.)
Markers are displayed only in the form of vertical lines.
The shaded areas  indicate what is set by the MARKER
BACK item.
VISTA markers CNSCO markers
VISTA markers and CNSCO markers
Two rows of dotted lines are displayed across the screen as
these markers.
Area markers
Dotted lines are displayed as the markers.
88% area markers
#5-)1	725
&OHMJTI
 
 
 
 
 .
 
 
						

							18
MAIN MENU
The underlined setting indicates the factory setting mode.
Item Setting DescriptionItem Setting Description
GAMMA SELECTGPI
NORMAL
FILM
For setting the gamma mode.
GPI:This is the GPI setting.  For
details, refer to “REMOTE
specifications” (page 22).
NORMAL:The normal gamma mode is
established.
FILM:The film mode that supports the
Varicam digital cine camera is
established.  The actual film mode
setting can be changed using the
FILM GAMMA item listed next.
COLOR TEMP.USER
D93
D65
D56
For setting the color temperature.USER:Any setting from 0 to 63 (equivalent
to a color temperature range from
3000 K to 9300 K) can be
established.
D93:This is equivalent to a color
temperature of 9300 K.
D65:This is equivalent to a color
temperature of 6500 K.
D56:This is equivalent to a color
temperature of 5600 K.

The color temperature can be set for each
gamma mode (NORMAL, FILM).
SD ASPECTGPI
16:9
4:3For setting the aspect ratio of the SD
signals.
GPI :This is the GPI setting.  For details,
refer to “REMOTE specifications”
(page 22).
16:9 :The images are displayed with a
16:9 aspect ratio.
4:3 :The images are displayed with a 4:3
aspect ratio.SHARPNESS
MODEHIGH
LOWFor setting the image sharpness.
HIGH:The images are accentuated with
fine edges.
LOW:The images are accentuated with
thick edges.

The sharpness can be set for VIDEO and
all other input channels.
SHARPNESS H0:
2:
30
For setting the image sharpness in the
horizontal direction.
This item enables two settings, one for the
VIDEO input signals and one for other
signals, to be stored in the memory.

≥While this item’s setting is selected, the
only information displayed on the screen
is this item which appears at the bottom
left regardless of the MENU POSI setting
selected on the OSD screen.
≥The sharpness can be set for VIDEO and
all other input channels.
MONOGPI
OFF
ON
For selecting monochrome images.
GPI:This is the GPI setting.  For details,
refer to “Concerning the REMOTE
specifications” (page 22).
OFF:Normal images
ON:Monochrome images

≥No adjustments are possible when RGB
signals are input.
≥When ON has been selected as this
item’s setting, the setting for the
CHROMA image control is fixed at 0.
When the setting is returned to OFF, the
CHROMA setting prior to the change is
restored.
SHARPNESS V0:
2:
30
For setting the image sharpness in the
vertical direction.
This item enables two settings, one for the
VIDEO input signals and one for other
signals, to be stored in the memory.

≥While this item’s setting is selected, the
only information displayed on the screen
is this item which appears at the bottom
left regardless of the MENU POSI setting
selected on the OSD screen.
≥The sharpness can be set for VIDEO and
all other input channels.
I-P MODEMODE2
MODE1For switching the IP conversion mode.MODE2:Movement compensation modeMODE1:Normal mode

This setting takes effect when progressive
signals (1080/30P, 1080/25P, 1080/24P,
720/60P or 480/60P) are input.
VIDEO CONFIG
FILM GAMMATYPE1
TYPE2This enables TYPE1 or TYPE2 to be
selected as the FILM setting for the
GAMMA SELECT item.
For the differences between TYPE1 and
TYPE2, refer to the graph below showing
the gamma characteristics curves.
Luminance
Input level
Normal gamma characteristics
TYPE1 characteristics
TYPE2 characteristics
#5-)1	725
&OHMJTI
 
 
 
 
 .
 
 
						

							19
Item Setting Description
GPI1-8UNDEF
MARKER1 ON/OFF
MARKER2 ON/OFF
MARKER BACK HALF
MARKER BACK BLACK
CENTER MARKER
INPUT SEL. SDI1
INPUT SEL. SDI2
INPUT SEL. VIDEO
INPUT SEL. YPBPR/RGB
SD ASPECT
HD ZOOM
BACKLIGHT MIN.
R.TALLY
G.TALLY
MONO ON/OFF
GAMMA SELECT
WFM ON/OFFFor allocating particular
functions to particular pins
when remote control
operations are to be
performed using the GPI
signals.  For details, refer to
“REMOTE specifications”
(page 22).
GPI
MAIN MENU
The underlined setting indicates the factory setting mode.
Item Setting Description
BACKLIGHT0:
60
For adjusting the backlight brightness to a
level from 0 to 60.  The higher the setting,
the brighter the backlight.
FUNCTIONWFMON/OFFHV DELAY
UNDEF
For setting the function to be allocated to
the FUNCTION/ENTER button.
WFM ON/OFF:The Y signal (luminance)
waveforms are displayed.
HV DELAY:The blanked parts of the
images are displayed.
UNDEF:No function is allocated.
WFMFUNCTIONGPIFor selecting whether the Y signal
(luminance) waveforms are to be displayed
using the FUNCTION/ENTER button or
from the GPI connector.
FUNCTION:The waveforms are displayed
using the FUNCTION/ENTER
button.
GPI:The operations are performed
from the GPI connector.  For
details, refer to “REMOTE
specifications” (page 22).
HD ZOOMFRONTGPIFor selecting whether the HD ZOOM
function is to be operated using the HD
ZOOM/Xbutton or from the GPI connector.
FRONT:The function is operated using the
HD ZOOM/Xbutton.
GPI:The operations are performed from
the GPI connector.  For details,
refer to “REMOTE specifications”
(page 22).
PEAKING/ PHASEPEAKINGPHASEFor selecting the PEAKING or PHASE
function for the image control.
PEAKING:The PEAKING function is
allocated to the control.
PHASE:The PHASE function is allocated
to the control.
USER MODE
LOADUSER5
USER4
USER3
USER2
USER1
FACTORYFor calling the file in which the user data is
stored.
USER1-5:These are the files in which the
user has stored data.  If the user
data has not yet been stored,
the settings are the same as the
ones in the FACTORY file.
FACTORY:This file contains the factory
settings.
USER MODE SAVEUSER5
USER4
USER3
USER2
USER1For saving the user data.
SYSTEM CONFIG
Item Setting Description
BATTERY REMAINOFF
ONFor selecting whether to display the
remaining battery charge.
OFF:The remaining charge is not displayed.ON:The remaining charge is displayed.
STATUS DISPLAYCONTINUE
3SEC. OFF
OFF
For setting how long the status display is to
remain on the screen.
CONTINUE:The status display appears
continuously at all times.
3SEC.OFF:The status display appears for
three seconds.
OFF:The status display does not appear.
CRCC MESSAGEOFF
ONFor selecting whether a message is to be
displayed when a CRCC error has been
detected.
OFF:A CRCC error message is not displayed.ON:A CRCC error message is displayed.
MENU POSITIONLTCENTER
LB
RB
RTFor setting the menu display position.LT:The menu is displayed at the top left.CENTER:The menu is displayed in the center.LB:The menu is displayed at the bottom left.RB:The menu is displayed at the bottom right.RT:The menu is displayed at the top right.
STATUS POSITIONLTCENTER
LB
RB
RTFor setting the status display position.LT:The menu is displayed at the top left.CENTER:The menu is displayed in the center.LB:The menu is displayed at the bottom left.RB:The menu is displayed at the bottom right.RT:The menu is displayed at the top right.
ROTARY
POSITIONLBCB
RB
RT
LT
CENTER
OFFFor setting the display position of the
settings when images have been adjusted
using the image controls.
LB:The settings are displayed at the
bottom left.
CB:The settings are displayed below the center.RB:The settings are displayed at the
bottom right.
RT:The settings are displayed at the top right.LT:The settings are displayed at the top left.CENTER:The settings are displayed in the center.OFF:The settings are not displayed.
OSD CONFIG
#5-)1	725
&OHMJTI
 
 
 
 
 .
 
 
						

							20
MAIN MENU
INPUT SELECT
Item Setting Description
SDI1 *1OFF
ONFor setting whether the SDI 1 signals can
be selected when the channels are to be
switched using the INPUT button.
OFF:The SDI 1 signals cannot be selected.ON:The SDI 1 signals can be selected.
FORMATAUTO1080/60I
1080/50I
1080/30P
1080/25P
1080/24P
1080/24PsF1035/60I
720/60P
720/60P
ANAMO
576/50I
480/60I
For selecting the signals whose input is to
be accepted at the SDI 1 connector.
AUTO:
All supported signals are accepted.
1080/60I:
1080/60I or 1080/59.94I format signals
are accepted.
1080/50I:
1080/50I format signals are accepted.
1080/30P:
1080/30P or 1080/29.97P format signals
are accepted.
1080/25P:
1080/25P format signals are accepted.
1080/24P:
1080/24P or 1080/23.98P format signals
are accepted.
1080/24PsF:
1080/24psF or 1080/23.98psF format
signals are accepted.
1035/60I:
1035/60I or 1035/59.94I format signals
are accepted.
720/60P:
720/60P or 720/59.94P format signals
are accepted.
720/60P ANAMO:
720/60P or 720/59.94P format signals
which support an anamorphic lens are
accepted.
576/50I:
576/50I format signals are accepted.
480/60I:
480/59.94I format signals are accepted.
The underlined setting indicates the factory setting mode.
*1Up to three of these items can be set to OFF at the same time.  Once the
three items have been set to OFF, it is no longer possible to set a fourth
item to OFF.  It is not possible to set all the inputs to OFF.
Item Setting Description
SDI2 *1OFF
ONFor setting whether the SDI 2 signals can
be selected when the channels are to be
switched using the INPUT button.
OFF:The SDI 2 signals cannot be selected.ON:The SDI 2 signals can be selected.
FORMATAUTO1080/60I
1080/50I
1080/30P
1080/25P
1080/24P
1080/24PsF1035/60I
720/60P
720/60P
ANAMO
576/50I
480/60I
For selecting the signals whose input is to
be accepted at the SDI 2 connector.
The setting selection is the same as for the
SDI 1 FORMAT item.
VIDEO *1OFF
ONFor setting whether the VIDEO signals can
be selected when the channels are to be
switched using the INPUT button.
OFF:The VIDEO signals cannot be selected.ON:The VIDEO signals can be selected.
FORMATAUTONTSC
PALFor selecting the signals whose input is to
be accepted at the VIDEO connector.
AUTO:
All supported signals are accepted.
NTSC:
NTSC signals are accepted.
PAL:
PAL signals are accepted.
YPBPR *1OFF
ONFor setting whether the YPBPR/RGB
signals can be selected when the channels
are to be switched using the INPUT button.
OFF:The YPBPR/RGB signals cannot be
selected.
ON:The YPBPR/RGB signals can be
selected.
MODEYPBPRRGBFor switching between the YPBPR and
RGB analog signals.
YPBPR:
The analog signals are switched to
Y/Pb/Pr.
RGB:
The analog signals are switched to RGB.
#5-)1	725
&OHMJTI
 
 
 
 
 .