Panasonic Microwave Ovens Ne 1054t Operating Instructions

							C. Programmed Heating:
Example: 1 stage; Memory Pad I to heal tor 3 minutes at HIGH Power
1.
3. Beep tone will sound.
.Press the Memory Pad 3.In Program Lock Mode oven will
start without pressing STARTPad. See page 15.
.Press the START Pad.
The total time for both stages
will be displayed. The time in
the Display Window will count down.
Heating will start..When lhe oven shifts to the next stage,
a single beep tone will sound.
.All heating will stop.When opening the door, the display
will stop blinking.
To Select Multiple Portion Healing:The Double Quantity Pad (x 2) is lactory sel to automatically double the programmed time for multipleportion heating.
ExamDle: Memorv Pad 5
E
@
,@
3. Beep tone will sound.
Example: 2 stage; Memory Pad 3 (to
See page 13 to program Memory Pad.
See page l5 to activate Program Lock.
t.
. /-DorrBr.E )
grui*J
3. Follow steps 2-3 above.
.Press the Memory Pad 9.ln Program Lock Mode oven will
start without pressing START
Pad. See page 15.
.Press the START Pad.
Heating will start.The time in the Display Window will
count down.
.All heating will stop.
When opening the door, the display
will stop blinking.
heat for 3 minutes at HIGH and 2 minutes at DEFROST)
.Press the DOUBLE OUANTITY (x 2)
Pad.
.Press the Memory Pad 5.
In Program Lock Mode oven will
start without pressing START
Pad. See page 15.
zm
(l5-1
l--ft
L UI
Display Windor.v
ILI
- 11 - 
						

							Disolav Window
l
tl
Disolay Window
l
ql
)
--:=-- =--7 nn
_t uu I
sro
LJJ 2z
Programming
- DO NOT OPEN THE DOOR _
The Display Window MUST be blank before programming can begin. lf any indicator light isilluminated in the digital Display Window: Close the door, press STOP/RESET Pad and wait 1minute until the Display Window goes blank.
A. Programming Memory Pads for Single Stage Heating:
Example: To program 30 seconds at Medium Power for Memory Pad Number 5
.Press the PFOG. Pad.
NOTE:.lf no PROG Indicator appeared in the
Display Window, Program Lock should
be cancelled. (See page 15.).Do not keep pressing PROG. Pad lor more
than 30 seconds, or a false tailure code
may result.
.Press N,lemory Pad 5.
The pad number and the previously
selected time and power level will
appear in the Display Window.
.The pad number and Stage
Heating Indicator will appear
in the Display Window again.
.Press the Porrrer Level Selector
Pad 3 times. The Memory Pad
display will go out.
.Press Memory Pads 3 and 0.
.Press the PROG. Pad again.
You have completed programming
the selected Memory Pad for
single stage heating and double
heating time for multiple portion
heating automatically.
.2 seconds later, the time andpower level setting for single
stage will appear in the Display Window.
.2 seconds later, Double Quantity (x 2)
Heating lndicator and then the
double heating time will appear
in the Display Window.
.2 seconds later, the Display Window
will go blank.
3.
I-lt,;;lL PowER l
EI
G;;I
4.
5.
rFt
-_]9__!!99____.1_
q
,- )
1 nn 1
| , _uu i
-12- 
						

							NOTE: . Program the remaining Memory Pads as desired by repeating steps 1-5. You may insert up to 10 memory Programs.. When the PROG indicator is blinking, the program can be cancelled and/or the Pad erased by pressing theSTOP/RESET Pad.
B. Programming Memory Pads for 2 or 3 Stage Heating:
Example: To program tor 2 minutes at DEFROST for 2 stage heaiing using Memory Pad Number 5
1. Complele Steps 1 to 4 or page 12.
.Press the POWER Level Selector Pad
5 trmes. DEF indicator light wiI hght.
.Press the Memorv Pads 2, 0 and 0.
@.Press the PROG. Pad again.
You have completed programming the
Selected l\,lemory Pad for 2 stage heating
and double heating time for mulliple portion
heatjng automatically.
.2 seconds later, the Display Window will show
your setting program as step 5 on page 12.
Display Window
---l!99---l-
[-i0]
..
Ii =J
- ;
GNT
lq Il
E
-_ !!!9_ _ _L_
I eogl
zm
o(rl5--l
.After all of your programming has been
completed. the Display Window will go blank. ]
NOTE; . Program the remaining pads as desired by repeating the steps above.
DO NOT OPEN THE OVEN DOOR during programming.. For a 3 stage heating cycle, select a further power level and set the desired healing time between steps 3 and 4 above.
-13- 
						

							C. Programming the Double Quantity Pad - For multiple portion heating:
your oven is lactory set to automatically double thg programmed time for multiple portion heating - this is the correct setting
tor heating multipleportions of most small foods items. No Iurther programming of the time is necessary for these lood items
The time iequired to heat multiple portions ot some large planers and most bulk food loads is slightly less than double that ol a
single portion.
Thi; model incorporates a Multiple Portion Heating Custom Program feature lhat allows you to customize the heating time
and/or power level for multiple portions of your menu items.
For example, if Memory Pad 3 is set for 6 minutes at DEFROST, 12 minutes at DEFROST is set for double quantity heating
automatically. Howevei, il your own tests have determined that the correct heating times required is less (only 10 minutes 30
seconds at OeFROSTI tot t*o portions, the Multiple Portion Heating Custom Program feature can be programmed tor 10
minutes 30 seconds at DEFROST.
Disolav window
I
.+e,+
2
t.
NOTE: . program the remaining Memory Pad as desired by repeating steps 1-6 above. (You may insert up to 10 memory
programs.)
DO NOT OPEN THE OVEN DOOR while programming
. When the PBOG indicator is blinking, the program can be cancelled and/or the pad erased by pressing STOP/RESET
Pad.
Example: To program 30 seconds at HIGH
I PBoG. I
Power on Memory Pad Number 2
.Press the PROG. Pad.
NOTE:.lf no PROG lndicator appeares in the
Display Window, Program Lock should be
cancelled (see page 15)..Do not keep pressing PROG. Pad for
more than 30 seconds, or a lalse
failure code may result.
.Press DOUBLE OUANTITY (x 2) Pad.
.Press Memory Pad 2.
The pad number and the PreviouslYselected time and power level for
multiple portion heating will
appear in the Display Window.
.The pad number and Stage Heating Indicator
will appear in the Display Window again.
.Press the POWER Level Selector Pad
once. The Memory Pad displaY will
go out.
.Press the Memory Pads 3, 0.
.Press the PROG. Pad again.
You have completed programming the
selected Memory Pad lor multiPle
portion heating.
.2 seconds later, the setting for single
stage heating will appear in the Display Window.
.2 seconds later, the Display Window
will go blank.
Fsro
uJz
2.
3.
r;;n
u15*J
4E
l-ril-lt PowER I
[E
F,a
t-
.-
f 
tol
))
lL
ru
tl
4.
-14- 
						

							Other Features
A. To Activate Program Lock:
This procedure Locks the control panel Memory Pads into their programmed heatingtimes and power levels. DO NOT OPEN THE DOOR. The Display Window must beblank before the Program Lock leature can be activated.
B. To Release Program Lock:
This procedure deactivates Program Lock and activates all other features.Oven reverts to a 2 touch operating mode (Memory Pad plus START Pad).DO NOT OPEN THE DOOR. The Display Window must be btank before the ReleaseProgram Lock feature can be activated.
Displav Window
1..Press the STOP/RESET Pad.
While pressing this pad, press thePROG. Pad until the DisplayWindow shows P (for 6 seconds).
.Program Lock Feature is deactivated,
oven is now in Program Unlock mode.
[;;;1 .@
NOTEi .Do not press PROG. Pad for longer than 30 seconds continuously, or a false failure code may result..ln Program Unlock
a. Repeat and interrupt features are operational.b. Memory Pads can be programmed.
c. Tone loudness control is operational.
Disolav Window
@.Press and hold in the PBOG. Pad
until the display showsP and 1. (for 6 seconds)
.Program Lock feature is now
actrvated.
NOTE:.DonotpressPROG.Padlorlongerthan30secondscontinuously,orfalsefailurecodemayresult..ln Program Lock
a. The oven is started by pressing the desired Memory pad. There is no need to press the START pad.
b. The interrupt feature is deactivated-opening the door cancels the remaining time on the program.
c. The oven cannot be programmed until the program lock feature is deactivated.
zm
(Jl5--l
-15- 
						

							C. To Read Program List:
Allows you to review all currently programmed Pad Number, heating time and power level for each
1. Open the door.
, 
F;;;I
.While pressing the STOP/RESET Pad,
press and hold in the START Pad.
The Beep Tone setting will show in the
Display Window.
Example; Stage Indicator l: Beep tone is ON
Stage Indicator 2: BeeP tone is OFF
2 seconds later, the Program Lock
setting will show in the Display
Window.
Program Lock : P L
Program Unlock: P
.Press Memory Pad you desired
to read program.
Example; The Memory Pad
Number 5.
Display Window will display;
Program Memory Pad Number 5,
first stage heating time and power
level currently programmed on
l\ilemory Pad.
2 seconds later, the same
intormation will be displayed
for the 2nd and 3rd stage
heating.
.After all settings have been
displayed, the Pad Number and
the Stage Heating Indicator will
appear in the Display Window again.
NOTE: .lf you want to go to another program, press the Memory Pad you desired to read program, while the information ot
lvlemory Pad is being displayed..lf you want to show the Multiple Portion Heating (x 2) program, press the DOUBLE OUANTITY Pad belore pressing
the l,remory Pad.
stage.
Displav window
t-n--l
I ul
+
I START I
Fs
luz
3.
-16- 
						

							D. To Select Beep Tone Options:
The Beep Tone can be set. ON or OFF.
Open the door.
@
E -
@
1.
Display Window
.Press the PFOG. Pad.
The display will not change.
.Press the Memory Pad 0.
.Repeat pressing ol 0 Pad. Select OFF
of Beep Tone.
Stage lndicator l -ON
Stagelndicator2=OFF
.Press the PROG. Pad again.You have completed programming
the beep tone.
.2 seconds later, the Display Window willgo blank.
.While pressing STOP/RESET Pad,press POWER Levei Selector Pad. Thedisplay shows the total cumulative number oftrmes the oven has been used.Example:.9999 means, the oven has beenused 999900 times..0020 means the oven has beenused 2000 times.. lf the total cumulative numberof times less than 100 times, thedisplay will not be changed.
.2 seconds later, 0 will reappear in theDisplay Window.
l
zm
(t5-.t
E. To Read the Cycle Counter:
The oven can dispiay the total number of times the oven has been operated cumulatively.Great for analyzing usage of the oven and tratfic flow at the,ocation.
1.Open the door.
I STOP,/RESET I
+
lrr;u9ry5r.l
Disolay Window
-17 - 
						

							rliflo
uJz
This oven monitors its operation and displays a Failure Code in the Display Window when a problem occurs.
Whal to do when a failure code appears:
NOTE: Above codes shown in Display Window do not indicate all the possible failures on the unit.
1. Unplug the oven before cleaning.
2. Keep the inside of the oven clean. When food spatters orspilled liquids adhere to oven walls, wipe with a damp cloth.N4ild detergent may be used if the oven gets very dirty. Theuse of harsh detergent or abrasives is not recommended.The air intake splash guard/light diffuser can be removed forcleaning by removing the center plugs from the two plastic
rivets. The top is held by two tabs.
Wash in warm dishwater and replace.
3. The outside oven surfaces should be cleaned with a dampcloth. To prevent damage to the operating parts inside theoven, water should not be allowed to seep into the ventilation
openrngs.
4. lf the Control Panel becomes wet, clean with a sott, dry cloth.Do not use harsh detergents or abrasives on Control Panel.
When cleaning the Control Panel, leave oven door open toprevent oven from accrdentally lurnrng on.After cleaning, touch STOP/RESET Pad to clear DisplayWindow.
5. lf steam accumulates inside or around the outside of the oven
door, wipe wilh a soft cloth. This may occur when thernicrowave oven is operated under high humidity conditions
and in no way indicates mallunction of the unit.
6. Clean off grease and dust on bottom surfaces otten. Usewarm detergent solution.
7. Cleaning inside the oven outer panel and inside the oven
base should be performed only by qualified service personnel
after taking precautions to drain all stored voltage potential.
The bottom is accessible by removing the center section of
the base and the power and sensor control areas are within
the outer wrap around housing. Avoid using liquids and
cleaning solutions in these areas. Use a dry sott bristle brush
or a cloth. Reolace all oarts-Do not connect the oven to the
electricity supply il any parts are not reassembled.
CODECAUSEWHAT TO DO
F01Overcooked lood.Temperature of exhaust air too high.
Press STOP/RESET Pad to stop beep.Wait for oven to cooi down and reset.lt a flame is Dresent, do not open oven door.lf normal operation does not resume, call the service agent with
information of tailure code.
F33-34Defective sensor circuit. Unplug the oven and wait more than 10
seconds before reconnecting.
lf normal operation does not resume, cali the
service agent with the information of tailure
code.
F44When a pad was pressed for more
than 30 secondsDetective pad or control circuit
-18- 
						

							NE-10547NE-10247
Power Source120V,60 Hz, single phase
Required Power13.44 1500W
Output1000 w
Frequency2,450 MNZ
Outer Dimensions
(HxWxD)
12 x2O/; x 14/;
306 mm x 510 mm x 360 mm
Cavity Dimensions
(HxWxD)
8l, x 13x 13
205 mm x 330 mm x 330 mm
NetApproximately 34 lb (15.4 kg)
Approximately 39 lbs (17.7 kg)
Timer99 min 99 sec (Digital)
x 10 Memory Pads
with Double Quantity
(x2) Pad
6 minutes Rotary
FRONTVIEW
.lEC 705-88 Test Procedure
Specifications subject to change without notice.
SIDE VIEWWITH
DOOR OPEN 
						

							PANASONIC CONSUMER ELECTONIC COMPANY
COMPANY DIVISION OF MATSUSHITA
ELECTRIC CORPORATION OF AMERICA
One Panasonic Way,4A-4, Secaucus, NJ 07094 TooogopooAp
{€01l 348-5377 )rinted in Taiwan