Panasonic Microwave Ovens Ne 1054_ne 1024 Operating Instructions

C. Programmed Heating:
Example: 1 stage; Memory Pad I to heal tor 3 minutes at HIGH Power
1.
3. Beep tone will sound.
.Press the Memory Pad 3.In Program Lock Mode oven will
start without pressing STARTPad. See page 15.
.Press the START Pad.
The total time for both stages
will be displayed. The time in
the Display Window will count down.
Heating will start..When lhe oven shifts to the next stage,
a single beep tone will sound.
.All heating will stop.When opening the door, the display
will stop blinking....

Disolav Window
l
tl
Disolay Window
l
ql
)
--:=-- =--7 nn
_t uu I
sro
LJJ 2z
Programming
- DO NOT OPEN THE DOOR _
The Display Window MUST be blank before programming can begin. lf any indicator light isilluminated in the digital Display Window: Close the door, press STOP/RESET Pad and wait 1minute until the Display Window goes blank.
A. Programming Memory Pads for Single Stage Heating:
Example: To program 30 seconds at Medium Power for Memory Pad Number 5
.Press the PFOG. Pad.
NOTE:.lf no PROG Indicator...

NOTE: . Program the remaining Memory Pads as desired by repeating steps 1-5. You may insert up to 10 memory Programs.. When the PROG indicator is blinking, the program can be cancelled and/or the Pad erased by pressing theSTOP/RESET Pad.
B. Programming Memory Pads for 2 or 3 Stage Heating:
Example: To program tor 2 minutes at DEFROST for 2 stage heaiing using Memory Pad Number 5
1. Complele Steps 1 to 4 or page 12.
.Press the POWER Level Selector Pad
5 trmes. DEF indicator light wiI hght.
.Press the...

C. Programming the Double Quantity Pad - For multiple portion heating:
your oven is lactory set to automatically double thg programmed time for multiple portion heating - this is the correct setting
tor heating multipleportions of most small foods items. No Iurther programming of the time is necessary for these lood items
The time iequired to heat multiple portions ot some large planers and most bulk food loads is slightly less than double that ol a
single portion.
Thi; model incorporates a Multiple...

Other Features
A. To Activate Program Lock:
This procedure Locks the control panel Memory Pads into their programmed heatingtimes and power levels. DO NOT OPEN THE DOOR. The Display Window must beblank before the Program Lock leature can be activated.
B. To Release Program Lock:
This procedure deactivates Program Lock and activates all other features.Oven reverts to a 2 touch operating mode (Memory Pad plus START Pad).DO NOT OPEN THE DOOR. The Display Window must be btank before the ReleaseProgram Lock...

C. To Read Program List:
Allows you to review all currently programmed Pad Number, heating time and power level for each
1. Open the door.
, 
F;;;I
.While pressing the STOP/RESET Pad,
press and hold in the START Pad.
The Beep Tone setting will show in the
Display Window.
Example; Stage Indicator l: Beep tone is ON
Stage Indicator 2: BeeP tone is OFF
2 seconds later, the Program Lock
setting will show in the Display
Window.
Program Lock : P L
Program Unlock: P
.Press Memory Pad you desired
to read...

D. To Select Beep Tone Options:
The Beep Tone can be set. ON or OFF.
Open the door.
@
E -
@
1.
Display Window
.Press the PFOG. Pad.
The display will not change.
.Press the Memory Pad 0.
.Repeat pressing ol 0 Pad. Select OFF
of Beep Tone.
Stage lndicator l -ON
Stagelndicator2=OFF
.Press the PROG. Pad again.You have completed programming
the beep tone.
.2 seconds later, the Display Window willgo blank.
.While pressing STOP/RESET Pad,press POWER Levei Selector Pad. Thedisplay shows the total cumulative...

rliflo
uJz
This oven monitors its operation and displays a Failure Code in the Display Window when a problem occurs.
Whal to do when a failure code appears:
NOTE: Above codes shown in Display Window do not indicate all the possible failures on the unit.
1. Unplug the oven before cleaning.
2. Keep the inside of the oven clean. When food spatters orspilled liquids adhere to oven walls, wipe with a damp cloth.N4ild detergent may be used if the oven gets very dirty. Theuse of harsh detergent or abrasives is...

NE-10547NE-10247
Power Source120V,60 Hz, single phase
Required Power13.44 1500W
Output1000 w
Frequency2,450 MNZ
Outer Dimensions
(HxWxD)
12 x2O/; x 14/;
306 mm x 510 mm x 360 mm
Cavity Dimensions
(HxWxD)
8l, x 13x 13
205 mm x 330 mm x 330 mm
NetApproximately 34 lb (15.4 kg)
Approximately 39 lbs (17.7 kg)
Timer99 min 99 sec (Digital)
x 10 Memory Pads
with Double Quantity
(x2) Pad
6 minutes Rotary
FRONTVIEW
.lEC 705-88 Test Procedure
Specifications subject to change without notice.
SIDE VIEWWITH
DOOR OPEN 

PANASONIC CONSUMER ELECTONIC COMPANY
COMPANY DIVISION OF MATSUSHITA
ELECTRIC CORPORATION OF AMERICA
One Panasonic Way,4A-4, Secaucus, NJ 07094 TooogopooAp
{€01l 348-5377 )rinted in Taiwan