Panasonic Memory Card Portable Recorder Player Ajhpm110 Operating Instructions

							Using Play List: Audio Split Editing91
 Using Play List
Audio Split Editing
Use audio split to shift the audio IN point relative to the video IN point (audio IN point split). Note that audio channels cannot be 
selected in this procedure. This function is performed on all channels together. 
Play list example 1 Play list example 2
6/A-
6
6
6 6
4
4
4
457
7
7
7 5
5
5New play list event
Preceding audio
6/A+
7
7 5
5 4
4
4
4566
6
7
7
56
New play list event
Silent segment
Delayed audio 
						

							92Using Play List: Audio Split Editing Use the following procedure to newly register an event 
containing an audio split. 
◆NOTE: 
 Refer to the “Adding and Registering Audio Split Point (Changing 
Registered Point)” section to add an audio split to a registered 
event. 
 First set the insert mode to INSERT. 
1Open the play list screen. 
2Use the cursor buttons to choose the location where 
you want to add the event. 
3Press the INSERT button. 
This activates the event register mode. 
4Register an IN point.
Use the operation buttons or search dial to look for a 
location to start an event. Then hold down the IN button 
and press the ENTRY button. 
5Register the audio split point. 
Use the operation buttons or search dial to look for a 
location for an audio SPLIT point. Then hold down the 
SPLIT button and press the ENTRY button. 
6Register an OUT point
Use the operation buttons or search dial to look for a 
location to end an event. Then hold down the OUT button 
and press the ENTRY button. 
7Press the EVENT button to end registration. 
The INSERT button will also terminate registration.
◆NOTE: 
 In the split display, “–” indicates forward while “+” indicates 
reverse direction.
 A split can be registered from the start of the original clip to the 
event OUT point. 
 Set the IN point before the split point. 
 A SPLIT where the audio precedes the video cannot be made 
for an event whose IN point is at the start of the clip. 
 When using the INSERT button to register a new event or using 
the EVENT button in a final event to register an event, register a 
SPLIT point before registering an OUT point as a new event will 
otherwise be registered. 
Registering From Video
4,5,6 653 4 2 17
IN OUTClip A
Play list
Event 02Event 01 Video
Audio
Possible audio split range 
						

							Using Play List: Audio Split Editing93
 Using Play List
You can add an audio split to an event registered in the play 
list and change the audio split point. 1Open the play list screen. 
2Use the cursor buttons to select the event where you 
want to add (or change) an audio split point. 
3Press the EVENT button. 
This activates the event edit mode.
4Register the audio split point.
Use the operation buttons or search dial to look for a 
location for an audio split point. Then hold down the SPLIT 
button and press the ENTRY button. 
5Press the EVENT button to end registration. 
◆NOTE: 
 Addition can take place even when the IN point is changed 
before step 4 or the OUT point is changed after step 4. 
You can change audio split points in frame increments (in 4-
frame increments at 24PN). 
1Open the play list screen. 
2Use the cursor buttons to select the event where you 
want to change an audio split point.
3Change the audio split point.
Hold down the SPLIT button and press the TRIM+ button 
or the TRIM– button. The IN point is incremented or 
decremented in frame increments (in 4-frame increments 
at 24PN). 
◆NOTE: 
 During trimming the split point is indicated in black numerals 
against a yellow background in the event list display of the event 
list split screen. 
Adding and Registering Audio Split Point (Changing Registered Point)
243,5 1
Trimming the Audio Split Point
24 1
3 
						

							94Using Play List: Audio Split Editing
4Press the ENTRY button to finalize the change. 
◆NOTE: 
 Trimming cannot be performed beyond the start point of an 
original clip. 
 The IN, OUT and SPLIT buttons allow you to use the TRIM+/– 
button for trimming in the event register screen when the time 
code is displayed. 
Use the following procedure to cancel an audio split setting. 
1Open the play list screen. 
2Use the cursor buttons to select the event where you 
want to cancel the split setting. 
3Hold down the SHIFT button and press the RESET 
button.
This cancels the audio split setting. 
◆NOTE: 
 Use the play list screen or the event register mode to cancel a 
split setting. 
 An audio split point is also cancelled by deleting the event IN 
point or by moving to a different clip. 
Cancelling an Audio Split Setting
23 1 
						

							Using Play List: Simplified Voice-Over95
 Using Play List
Simplified Voice-Over
This function allows you to make voice-overs and give priority to the voice-over during playback. Recording is performed on 
one or two channels. The channel input during recording can be mixed with the playback sound. 
◆NOTE: 
 The voice-over data is written to the same card storing the play list. 
Thus the play list must be saved before audio recording or an error 
will be generated and recording cannot be performed. 
 The maximum recording time is 720 minutes. 
 The maximum number of voice-overs is 99.  Check the remaining time on the P2 card before saving the play list. 
Otherwise there may not be enough time for the voice-over 
recording. When the P2 becomes FULL, an error occurs and 
recording cannot be started. 
 Simplified voice over is not available when 24 or 60-24 is selected in 
setup menu No. 25 SYSTEM FREQ.
Make the required settings in the related setup menu prior to 
a voice over recording.
➝For details on settings, refer to “Setup” (page 115).
Select the voice-over track from one of the following tracks in 
setup menu No. 792 (A DUB CH):
CH1, CH2, CH3, CH4, CH1+2, CH3+4
◆NOTE: 
 Recording tracks can be selected when the play list does not 
contain any voice-overs. When it does contain a voice-over, 
subsequent voice-overs use the same recording track. 
You can select whether to mix the playback sound during a 
voice-over in setup menu No. 793 (A DUB PB MIX). 
When mixing is selected, select the channels to mix in setup 
subscreen.
The playback sound of the selected channels is mixed with A 
DUB CH and recorded. 
When there are multiple A DUB CH, make separate settings 
for each. 
◆NOTE:
 In play list playback, playback level is set to UNITY fixed, or 
registered recording level and cannot be changed. However, EE 
audio while the A.DUB button is pressed and during A.DUB can be 
adjusted. 
 The playback level of short playback of voice-overs from still status 
cannot be changed. 
In setup menu No. 796 (A DUB FADE), select whether the 
voice-over should be blended with the original audio using cut 
or V-fade.
This setting is reflected to play list playback and edit copy.
➝Refer to “Playing Back the Play List” (page 101).
➝Refer to “Creating New Clips From the Play List (Edit Copy)” 
(page 102).
◆NOTE:
 When an audio is overwritten and added using cut to an audio 
added by V-fade, V-fade will be applied to the connecting point.
In setup menu No. 797 (A DUB MONI), select whether the 
audio being recorded should be output during the voice-over. 
Connect a microphone to analog CH2 and mix the 
microphone input with CH2 playback audio and use cut 
processing to record on CH2. Use headphones to listen to the 
playback audio during recording. 
Preparing for Voice-Over
Selecting a Track for Recording
Mixing Playback Sound
Selecting Method for Connecting Audio IN 
and OUT Points
Setting Output Voice During A DUB
Setup Example
Selecting recording tracks A DUB CH = CH2
Selecting mixing with playback 
soundA DUB PB MIX = ON
CH2 MIX = CH2
Selecting audio connection A DUB FADE = CUT
During simultaneous A DUB 
settingA DUB MONI = OFF 
						

							96Using Play List: Simplified Voice-Over
◆NOTE:
 Input a reference signal when mixing SDI input audio. 
 IEEE1394 input audio cannot be used for voice-overs. 
1Open the play list screen. 
2Use the cursor buttons to select the event where you 
want to perform a voice-over. 
3Find the location for the voice-over.
Use the operation buttons or the search dial to find a 
location for a voice-over and press STILL  . 
4Press the A.DUB button. 
This generates an A DUB PAUSE state while a still image 
is output at the still location. 
5Press the STILL   button. 
Press the STILL   button again. After a 2-second auto 
reverse and a 2-second playback interval, sound 
recording starts. 
Use the VR (audio volume) controls as necessary to adjust 
the playback sound level.
6Press the STOP   button to end the voice-over. 
◆NOTE: 
 When the 24PN play list format is set in setup menu No. 026 
(PLY LST FMT), the audio IN and OUT points are set in 4-frame 
increments. If the recording starts or stops at some other points, 
the IN and OUT points are automatically corrected within the 
recording range. 
1Open the play list screen. 
2Use the cursor buttons to select the event where you 
want to perform a voice-over. 
3Press the PLAY   button to start playback at a 
location before the voice-over. 
4Hold down the A.DUB button and press the PLAY   
button at the voice-over location. 
This starts the audio recording. 
Use the VR (audio volume) controls as necessary to adjust 
the playback sound level.
5Press STOP   button to end the voice-over.
◆NOTE: 
 When the 24PN play list format is set in setup menu No. 026 
(PLY LST FMT), the audio IN and OUT points are set in 4-frame 
increments. If the recording starts or stops at some other points, 
the IN and OUT points are automatically corrected to fall within 
the recording range. 
Voice-Over From Still Image Status
3,5 264
1
Voice-Over From Playback Status
3 254
1 
						

							Using Play List: Simplified Voice-Over97
 Using Play List
The voice-over appears in the play list screen as shown below. 
1)Play List
 The voice-over is added to the line after an event with an 
audio start point. 
 The “No.” column shows “EX*,” not an event number.
 The “SLOT” column shows P2 card slot numbers storing 
audio data (same as P2 card slots storing the play list). 
2)Timeline
 Extended tracks are indicated in the “EXTRA” part. 
 Recorded channel numbers are also shown.
◆NOTE:
 Use the TRIM button to zoom in (+) and zoom out (–). 
 When a card with a voice-over is not inserted (and NONE is 
indicated), play list files cannot be saved and EXTRA audio 
event cannot be deleted. 
This function allows you to adjust the location of a voice-over 
in frame increments (at 24PN in 4-frame increments). 
1Open the play list screen. 
2Select the event you want to change.
3Use the following procedure to change offset and 
duration.
4Press the ENTRY button to finalize the change. 
◆NOTE:
  Except for the ENTRY button, you can also use the SET button 
or move the cursor with the cursor buttons to finalize a change.
Displaying Voice-Over Events
Changing the Trimming of Audio 
Recording Location
1)
2)
23 41
Change of 
start 
location:Hold down the IN button and press the 
TRIM+ button or the TRIM– button. The 
start location is incremented or 
decremented in frame increments (in 4-
frame increments at 24PN).
Change of 
end 
location: Hold down the OUT button and press the 
TRIM+ button or the TRIM– button. The 
OUT point is incremented or decremented 
in frame increments (in 4-frame 
increments at 24PN).
A normal event
EXTRA 
audio track
EXTRA 
audio track
EXTRA 
audio track
Change of OUT+ TRIM duration
Change of IN + TRIM audio start location 
						

							98Using Play List: Viewing Event Information
Viewing Event Information
You can use this function to view and confirm miscellaneous 
event information. 
1Open the play list screen. 
2Use the cursor buttons to select the event that you 
want information about. 
3Press the MENU button. 
4Use the cursor buttons to choose [PROPERTY] – 
[EVENT PROPERTY] and press the SET button. 
Information on the event appears. 
◆NOTE:
 Holding down the SHIFT button in step 2 while pressing the 
SPLIT button will also open the event information screen. 
 You can use the cross cursor buttons to move to the previous or 
next event while viewing event information. 
1)Event information
Event number
IN point and OUT point thumbnails and TC value
TOTAL (length from the beginning of the 1st event to 
the end of the current event)
DURATION (event length)
A SPLIT (audio split length) 
TRACK / A CH
(Track status and audio channel status: AV = audio 
and video/FADE (CUT) = EXTRA audio splicing, 
indication of channels inserted in channels 1 - 4.) 
2)Original clip information for an event
Clip number (same as thumbnail display number)
Clip thumbnail
Various indicators and write protect status
CLIP NAME (name of clip)
START TC (start value of time code)
START UB (user bit start value)
DATE (record date) 
TIME (recording time)
USER CLIPNAME (clip name assigned by the user)
3)Timeline
5Press the EXIT button to end information display. 
Indicating Event Property
2,4 3 1
2)
3)
1) 
						

							Using Play List: Viewing Event Information99
 Using Play List
You can use this function to check the content of an event by 
playing if from its IN point to its OUT point. 
1Open the play list screen. 
2Use the cursor buttons to select the clip you want to 
review.
3Hold down the SHIFT button and press the PLAY   
button.
This plays back the clip from before the IN point (preroll 
time is 3 s) to beyond its OUT point (postroll time is 1 s). 
◆NOTE: 
 The preroll time and postroll time for the first and last clip are 
both 0 s. 
 When review stops or you press the STOP  button, playback 
stops and you return to the play list screen. 
During review all buttons other than the STOP   button are not 
available. 
 A review operation can be re-started during the review currently 
in progress.
Event Review
23 1 
						

							100Using Play List: Playing Back Play Lists
Playing Back Play Lists 
During play list playback, you can select whether the time 
code should be replaced and output as a continuous value or 
the time code of each clip should be output. You can set the 
time code start value when it is replaced at output. 
1Open the play list screen. 
2Press the MENU button. 
3Use the cursor buttons to choose [SETTING] – 
[REPLACE TC] – [REPLACE]. 
4Select [ON] and press the SET button.
This replaces the playback time code. 
◆NOTE: 
 When [OFF] is set, the time code is not replaced, instead the 
time code of each clip is output. 
 When [OFF] is set, go to step 7 and end setup. 
5Use the cursor buttons to choose [SETTING] – 
[REPLACE TC] – [START TC] and press the SET 
button to enter the start time code. 
The initial value of the start time code is 00:00:00:00 when 
replaced. 
6Use the cursor buttons to choose [SETTING] – 
[REPLACE TC] – [DROP FRAME]. Then press the 
SET button and select [DF] (drop frame) or [NDF] 
(non drop frame).
◆NOTE: 
 A [DF] setting cannot be made at 24PN. 
 [DROP FRAME] does not appear when 50, 25 or 60-25 is 
selected in setup menu No. 25 SYSTEM FREQ.
7Press the MENU button to end setup. 
Setting the Playback Time Code (TC)