Panasonic Memory Card Camera Recorder AG-AC160AP, AG-AC160AEJ, AG-AC160AEN Operating Instructions

							Model No.	AG-AC160AP
	 AG-AC160AEJ
	 AG-AC160AEN
SS0412SI0 -YI
Printed in Japan VQT4J51 (E)ENGLISH
Vol.1
Note that Operating Instructions Vol.1 describes basic operations of 
the Memory Card Camera-Recorder.
For  instructions  on  advanced  operations  of  the  Memory  Card 
Camera-Recorder,  refer  to  Operating  Instructions  Vol.2  (pdf  file) 
contained in the supplied CD-ROM. (Page
 13)
		This	product	is	eligible	for	the	AVCCAM	3	Year	W
arranty	Repair	Program.	For	details,	see	page	9.Operating Instructions
Memory Card Camera-Recorder
Before operating this product, please read the instructions carefully and save this manual for 
future use.
Volume1 
						

							2
indicates safety information.
WARNING:•	 To	reduce	the	risk	of	fire	or	electric	shock,	do	not	expose	this equipment to rain or moisture.
•	 To	reduce	the	risk	of	fire	or	electric	shock	hazard,	keep	this  equipment  away 

from  all  liquids.  Use  and  store  only 
in
	locations	which	are	not	exposed	to	the	risk	of	dripping	or splashing liquids, 

and do not place any liquid containers 
on top of the equipment.
WARNING: Always keep memory cards or accessories (coin battery, 
microphone holder screws, microphone holder adaptor, 
INPUT terminal covers) out of the reach of babies and small 
children.
CAUTION:To reduce the risk of fire or electric shock and annoying 
interference, use the recommended accessories only.
CAUTION:Do not jar, swing, or shake the unit by its handle while the 
conversion lens or another accessory is attached. 
Due to the added weight of the conversion lens, any strong 
jolt to the handle may damage the unit or result in personal 
injury.
CAUTION:The mains plug of the power supply cord shall remain 
readily operable.
The AC receptacle (mains socket outlet) shall be installed 
near the equipment and shall be easily accessible.
To completely disconnect this equipment from the AC 
mains, disconnect the power cord plug from the AC 
receptacle.
CAUTION:Danger	of	explosion	or	fire	if	battery	is		incorrectly	replaced	or mistreated.
•	 Do	not	disassemble	the	battery	or	dispose	of	it	in	fire.
•	 Do not store in temperatures over 60°C (140°F).
•	 Do
	not	expose	the	battery	to	excessive	heat	such	as	sun-
shine,	fire	or	the	like.For Battery Pack•	 Use	specified	charger.
•	 Replace	only	with	same	or	specified	type.For Battery of Remote Controller•	Replace battery with part No. CR2025 only.
•	 Do not recharge the battery.
CAUTION:In order to maintain adequate ventilation, do not install or 
place this unit in a bookcase, built-in cabinet or any other 
confined space.  
To	prevent	risk	of	electric	shock	or	fire	hazard	due	to overheating, ensure that curtains and any other 
materials do not obstruct the ventilation.
CAUTION:Do not lift the unit by its handle while the tripod is attached. 
When the tripod is attached, its weight will also affect 
the unit’s handle, possibly causing the handle to break 
and hurting the user. To carry the unit while the tripod is 
attached, take hold of the tripod.
CAUTION:Excessive	sound	pressure	from	earphones	and	headphones can cause hearing loss.
CAUTION:Do not leave the unit in direct contact with the skin for long 
periods of time when in use.  
Low temperature burn injuries may be suffered if the high 
temperature parts of this unit are in direct contact with the 
skin for long periods of time. When using the equipment for 
long periods of time, make use of the tripod.
CAUTION:Keep metal objects (such as necklaces and hairpins) away 
from the battery.
Short-circuiting may occur across the terminals, causing the 
battery to heat up, and you may seriously burn yourself if 
you touch the battery in this state.
Read this first!
The lightning flash with arrowhead symbol, 
within an equilateral triangle, is intended to 
alert the user to the presence of uninsulated 
“dangerous voltage” within the product’s 
enclosure that may be of sufficient magnitude 
to constitute a risk of electric shock to persons.
The	exclamation	point	within	an	equilateral  
triangle is intended to alert the user to 
the presence of important operating and 
maintenance (servicing) instructions in the 
literature accompanying the appliance.
   
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN    
CAUTION: TO REDUCE THE RISK OF ELECTRIC 
SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER TO SERVICING TO QUALIFIED SERVICE  PERSONNEL. 
						

							3
CAUTION:
This	apparatus	can	be	operated	at	a	voltage	in	the	range	of	110-240	V	AC.
Voltages	other	than	120	V	are	not	intended	for	U.S.A.	and	Canada.
Operation	at	a	voltage	other	than	120	V	AC	may	require	the	use	of	a	dif

ferent
	AC	plug.	Please	contact	either	a	local	or	foreign	Panasonic	authorized	service	center	for	assistance	in	selecting	an	alternate	AC	plug.
FCC NOTICE (USA)
Declaration of ConformityModel	Number:	 	 AG-AC160AP
Trade	Name:	 	 Panasonic
Responsible
	Party:		Panasonic	Corporation	of	North	America	One	Panasonic	W ay,	Secaucus,	NJ	07094Support	contact:		 1-800-524-1448
This	device	complies	with	Part	15	of	the	FCC	Rules.
Operation	is	subject	to	the	following	two	conditions:
(1)	This	device	may	not	cause	harmful	interference,	and	(2)	this	device	must	accept	any	interference	received,	including	interference	that	may	cause	undesired	operation.
T

o
	assure	continued	compliance,	follow	the	attached	installation	instructions	and	do	not	make	any	unauthorized	modifications.
CAUTION:This	equipment	has	been	tested	and	found	to	comply	with	the	limits	for	a	Class	B	digital	device,	pursuant	to	Part	15	of	the	FCC	Rules.	These	limits	are	designed	to	provide	reasonable	protection	against	harmful	interference	in	a	residential	installation.	This	equipment	generates,	uses	and	can	radiate	radio	frequency	energy	and,	if	not	installed	and	used	in	accordance	with	the	instructions,	may	cause	harmful	interference	to	radio	communications.	However
 ,
	there	is	no	guarantee	that	interference	will	not	occur	in	a	particular	installation.	If	this	equipment	does	cause	harmful	interference	to	radio	or	television	reception,	which	can	be	determined	by	turning	the	equipment	of

f
	and	on,	the	user	is	encouraged	to	try	to	correct	the	interference	by	one	of	the	following	measures:
•	

Reorient
	or	relocate	the	receiving	antenna.
•	

Increase
	the	separation	between	the	equipment	and	receiver
 .
•	 Connect	the	equipment	into	an	outlet	on	a	circuit	different	from	that	to	which	the	receiver	is	connected.•	 Consult	the	dealer	or	an	experienced	radio/TV	technician	for	help.
The	user	may	find	the	booklet	“Something	About	Interference”	
available	from	FCC	local	regional	of

fices
	helpful.
FCC Warning:To	assure	continued	FCC	emission	limit	compliance,	follow	the	attached	installation	instructions	and	the	user	must	use	only	shielded	interface	cables	when	connecting	to	host	computer	or	peripheral	devices.	Also	any	unauthorized	changes	or	modifications	to	this	equipment	could	void	the	user's	authority	to	operate	this	device.
NOTIFICATION (Canada)
This	class	B	digital	apparatus	complies	with	Canadian	ICES-003.
Cet	appareil	numéique	de	la	classe	B	est	conforme	à	la	norme	NMB-003	du	Canada.
For AG-AC160AP Onlyindicates	safety	information. 
						

							4
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the ma\
nufacturer’s instructions.
8)  Do not install near any heat sources such as radiators, heat registers, \
stoves, or other apparatus 
(including amplifiers) that produce heat.
9)	
	Do	not	defeat	the	safety	purpose	of	the	polarized	or	grounding-type	plug.	A	polarized	plug	has	two	blades with one wider than the other. A

 grounding-type plug has two blades and a third grounding prong. 
The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your 
outlet, consult an electrician for replacement of the obsolete outlet.
10)
   Protect the power cord from being walked on or pinched particularly at plugs, convenience 
receptacles,	and	the	point	where	they	exit	from	the	apparatus.
11)		Only	use	attachments/accessories	specified	by	the	manufacturer.
12)   Use only with the cart, stand, tripod, bracket, or table specified by th\
e manufacturer, 
or	sold	with	the	apparatus.	When	a	cart	is	used,	use	caution	when	moving	the	cart/	apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long pe

riods of time.
14)
   Refer all servicing to qualified service personnel. Servicing is required wh

en the 
apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has 
been
	spilled	or	objects	have	fallen	into	the	apparatus,	the	apparatus	has	been	exposed	to	rain	or	moisture, does not operate normally, or has been dropped.
IMPORTANT“Unauthorized	recording	of	copyrighted	television	programs,	video	tapes	and	other	materials	may	infringe	the	right of copyright owners and be contrary to copyright laws.”
For USA-California Only 
This product contains a CR Coin Cell Lithium Battery which contains Perc\
hlorate Material – special 
handling may apply.
See
	www.dtsc.ca.gov/hazardouswaste/perchlorate
A	lithium	ion/polymer	battery	that	is	recyclable	powers	the	product	you	have	purchased.
Please call 1-800-8-BATTER Y for information on how to recycle this battery. 
						

							5
Caution	for	AC	Mains	Lead
For battery charger
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This product is equipped with 2 types of AC mains cable. One is for continental Europe, etc. 
and the other one is only for U.K.
Appropriate
	mains	cable	must	be	used	in	each	local	area,	since	the	other	type	of	mains	cable	is
not	suitable.
TYPE C
(FOR CONTINENTAL EUROPE, ETC.
Not to be used in the U.K.)TYPE BF
(FOR U.K. ONLY)
How to replace the fuse
1. 
 Open the fuse compartment with a 
screwdriver.
2. Replace the fuse. Fuse
FOR U.K. ONLY
This appliance is supplied with a moulded 
three pin mains plug for your safety and 
convenience.
A 5 amp fuse is fitted in this plug.
Should the fuse need to be replaced please 
ensure that the replacement fuse has a 
rating of 5 amps and that it is approved by 
ASTA or BSI to BS1362.
Check for the ASTA mark 
 or the BSI mark  on the body of the fuse.
If the plug contains a removable fuse cover 
you must ensure that it is refitted when the 
fuse is replaced.
If you lose the fuse cover the plug must 
not be used until a replacement cover is 
obtained.
A replacement fuse cover can be purchased 
from your local Panasonic Dealer.
indicates	safety	information.For AG-AC160AEJ Only
EEE Yönetmeliğine Uygundur.
EEE Complies with Directive of Turkey.
EU 
						

							6
Caution	for	AC	Mains	Lead
For AC adaptor
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This product is equipped with 2 types of AC mains cable. One is for continental Europe, etc. 
and the other one is only for U.K.
Appropriate
	mains	cable	must	be	used	in	each	local	area,	since	the	other	type	of	mains	cable	is
not	suitable.
FOR CONTINENTAL EUROPE, ETC.
Not to be used in the U.K.FOR U.K. ONLY
How to replace the fuse
1. 
 Open the fuse compartment with a 
screwdriver.
2. Replace the fuse. Fuse
FOR U.K. ONLY
This appliance is supplied with a moulded 
three pin mains plug for your safety and 
convenience.
A 13 amp fuse is fitted in this plug.
Should the fuse need to be replaced please 
ensure that the replacement fuse has a rating 
of 13 amps and that it is approved by ASTA 
or BSI to BS1362.
Check for the ASTA mark 
 or the BSI mark  on the body of the fuse.
If the plug contains a removable fuse cover 
you must ensure that it is refitted when the 
fuse is replaced.
If you lose the fuse cover the plug must 
not be used until a replacement cover is 
obtained.
A replacement fuse cover can be purchased 
from your local Panasonic Dealer.
indicates	safety	information.For AG-AC160AEJ Only
WARNING:	This	equipment	must	be	earthed
To	ensure	safe	operation,	the	three-pin	plug	must	be	inserted	only	into	a	standard	three-pin	power	point	which	is	ef

fectively
	earthed	through	normal	house-hold	wiring.
Extension	cords	used	with	the	equipment	must	have	three	cores	and	be	correctly	wired	to	provide	connection	to	the	earth.	W

rongly
	wired	extension	cords	are	a	major	cause	of	fatalities.
The	fact	that	the	equipment	operates	satisfactorily	does	not	imply	that	the	power	point	is	earthed	or	that	the	installation	is	completely	safe.	For	your	safety

,
	if	you	are	in	any	doubt	about	the	ef
 fective
	earthing	of	the	power	point,	please	consult	a	qualified	electrician. 
						

							7
EMC NOTICE FOR THE PURCHASER/USER OF THE APPARATUS
1. Applicable standards and operating environmentThe apparatus is compliant with: •	 standards
	EN55103-1	and	EN55103-2	2009,	and
•	

electromagnetic
	environments	E1,	E2,	E3	and	E4.
2. Pre-requisite conditions to achieving compliance with the above standards  
 Peripheral equipment to be connected to the apparatus and special connecting cables
•	 The	purchaser/user	is	urged	to	use	only	equipment	which	has	been	recommended	by	us	as	peripheral	equipment	to	be	connected	to	the	apparatus.
•	

The
	purchaser/user	is	urged	to	use	only	the	connecting	cables	described	below
 .
 
 For the connecting cables, use shielded cables which suit the intended purpose of the apparatus.•	 Video	signal	connecting	cables 	
Use	double-shielded	coaxial	cables,	which	are	designed	for	75-ohm	type	high-frequency	ap -
plications,
	for	SDI	(Serial	Digital	Interface).

	
Coaxial
	cables,	which	are	designed	for	75-ohm	type	high-frequency	applications,	are	recom

-
mended
	for	analog	video	signals.
•	

Audio
	signal	connecting	cables
 	
If	your	apparatus	supports	AES/EBU	serial	digital	audio	signals,	use	cables	designed	for	AES/EBU.Use	shielded	cables,	which	provide	quality	performance	for	high-frequency	transmission	ap-
plications,	for	analog	audio	signals.
•	
Other
	connecting	cables	(IEEE1394,	USB)

	
Use
	double-shielded	cables,	which	provide	quality	performance	for	high-frequency	applica

-
tions,
	as	connecting	cables.
•	

When
	connecting	to	the	DVI	signal	terminal,	use	a	cable	with	a	ferrite	core.
•	

If
	your	apparatus	is	supplied	with	ferrite	core(s),	they	must	be	attached	on	cable(s)	following	instructions	in	this	manual.
3. Performance level The
	performance	level	of	the	apparatus	is	equivalent	to	or	better	than	the	performance	level	required	by	these	standards.
However

,
	the	apparatus	may	be	adversely	af
 fected
	by	interference	if	it	is	being	used	in	an	EMC	environment,	such	as	an	area	where	strong	electromagnetic	fields	are	generated	(by	the	presence	of	signal	transmission	towers,	cellular	phones,	etc.).	In	order	to	minimize	the	adverse	ef

fects
	of	the	interference	on	the	apparatus	in	cases	like	this,	it	is	recommended	that	the	following	steps	be	taken	with	the	apparatus	being	af

fected
	and	with	its	operating	environment:
1.	Place	the	apparatus	at	a	distance	from	the	source	of	the	interference.
2.	Change	the	direction	of	the	apparatus.
3.	Change	the	connection	method	used	for	the	apparatus.
4.		Connect	the	ap paratus	to	an other	po wer	ou tlet	wh ere	th e	po wer	is	no t	sh ared	by	an y	ot her	ap pliances.
For AG-AC160AEJ/AG-AC160AEN Only
For AG-AC160AEN Only
Caution	for	AC	Mains	Lead
AC adaptor (Battery charger)
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This product is equipped with 2 types of AC mains cable, Type C and Type BF.
Appropriate
	mains	cable	must	be	used	in	each	local	area,	since	the	other	type	of	mains	cable	is
not	suitable.
TYPE CTYPE BF
indicates	safety	information. 
						

							8
To remove the battery
Para remover a bateria
Main Power Battery (Lithium ion Battery)
Bateria Principal de Energia
(Refer to page
 26 for the detail.)
Press the battery release button.
Pressione o botão para liberar a bateria.
Back-up Battery (Lithium Battery)
•	 For  the 

removal  of  the  battery  for  disposal  at 
the  end  of  its  service  life,  please  consult  your 
dealer.
Battery release button
Botão de liberação da 
bateria
Remote Control Battery (Lithium Battery)
Bateria do Controle Remoto
1)
  Push the catch in the direction shown by 
arrow 1 to remove the holder

.
Empurre
	a	trava	na	direção	exibida	pela	seta	1 para remover o suporte.
2)
  Remove the button-type battery from the 
battery holder. 
Remova a bateria tipo botão do suporte da 
bateria.
Brazil Only 
Brasil Apenas
 „ Manuseio de baterias usadas
BRASILApós	o	uso,	as	pilhas	e	/ou	baterias	poderão	ser entregues ao estabelecimento comercial 
ou	rede	de	assistência	técnica	autorizada.
Cobrir os terminais positivo (+) e negativo (-) com uma fita isolant\
e adesiva, antes de depositar numa 
caixa
	destinada	para	o	recolhimento.	O	contato	entre	partes	metálicas	pode	causar	vazamentos,	gerar	calor,	romper	a	blindagem	e	produzir	fogo.
Não	desmonte,	não	remova	o	invólucro,	nem	amasse	a	bateria.	O	gás	liberado	pela	bateria	pode	irritar	a	garganta,	danificar	o	lacre	do	invólucro	ou	o	vazamento	provocar	calor,	ruptura	da	blindagem	e	produzir	fogo devido ao curto circuito dos terminais. Não incinere nem aqueç\
a as baterias, elas não podem ficar 
expostas	a	temperaturas	superiores	a	100°C	(212°F).	O	gás	liberado	pela	bateria	pode	irritar	a	garganta,	danificar	o	lacre	do	invólucro	ou	o	vazamento	provocar	calor,	ruptura	da	blindagem	e	produzir	fogo	devido	ao curto circuito dos terminais provocado internamente.
Evite	o	contato	com	o	liquido	que	vazar	das	baterias.	Caso	isto	ocorra,	lave	bem	a	parte	afetada	com	bastante	água.	Caso	haja	irritação,	consulte	um	médico. 
						

							9
Battery Charger / AC Adaptor
The rating plate is on the underside of the Battery Charger and AC Adaptor. Disconnect the AC mains 
plug from the AC mains socket when not in use.
*1: Please note that this extended warranty is not available in some countries/regions.  *2: Not all models eligible for extended warranty coverage.  
*3: The basic warranty period may vary depending on the country/region.  *4: Not all repair work is covered by this extended warranty.  
Purchase 
AVCCAM product Register online 
within 1 month“Registration Notice”  e-mail sent
Details about user registration and the extended warranty: http://panasonic.biz/sav/pass_e
Free 3 years of  Warranty Repairs
Customers who register as users on the website will receive an extended warranty repair valid for up to 
three years. 
AVCCAM 3 Year Warranty Repair Program *1
Thank you for purchasing this Panasonic AVCCAM device.
Register as a user for this device to receive a special service warranty up to three years of free warranty repairs.
Make sure to save the “Registration Notice” e-mail 
during the warranty period.
Please note, this is a site that is not maintained by Panasonic Canada Inc. The Panasonic Canada Inc. privacy policy does not apply and is not applicable in relation to any 
information submitted. This link is provided to you for convenience.
1st year 2nd year3rd year
AVCCAM device*2Basic warranty*3Extended warranty repair*4
It has been found that counterfeit battery packs which look very similar to the genuine product are 
made available to purchase in some markets. Some of these battery packs are not adequately 
protected with internal protection to meet the requirements of appropriate safety standards.  There is 
a possibility that these battery packs may lead to fire or explosion. Please be advised that we are not 
liable for any accident or failure occurring as a result of use of a counterfeit battery pack. To ensure that 
safe products are used we would recommend that a genuine Panasonic battery pack is used.
■ Batteries that may be used with this product (Correct as of September 201 1)   Panasonic CGA-E/625 (bundled) and VW-VBG6 (optional) batteries may be used with this product.    The CGA-E/625 (bundled) and VW-VBG6 (optional) batteries contain a function to enable verification as 
to whether they may be safely used with this product. 
						

							10
■
■ How to read this document
Illustrations •Illustrations of the camera, menu screens, and other items, may vary fro\
m the actual items. •In order to identify the terminals on the camera body, the supplied protective caps are not illustrated 
except	in	“Description	of	parts”	(Pages	22,	23).
Reference pages
 • Reference pages in this document are indicated by (Page 00).
SD/SDHC/SDXC memory cards
 • SD/SDHC/SDXC	memory	cards	are	all	described	as	memory	cards.	Each	name	is	described	when	explained	individually.
Notations
 • The menu items displayed on the screen are enclosed in square brackets l\
ike [Menu items], and 
characters printed on camera and the remote control are enclosed in angl\
e brackets as in .
Menu display language
 • [English] is set in the factory settings. You can change the display language in [LANGUAGE] item of the 
[OTHER FUNCTIONS] screen.
 •The	SDHC	logo	and	SDXC	logo	are	trademarks	of	SD-3C,	LLC.	
 
• “AVCHD” and the “AVCHD” logo are trademarks of Panasonic Corporation and Sony Corporati\
on. •The “DV” is a registered trademark. •Manufactured under license from Dolby Laboratories.  
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
 •HDMI,	the	HDMI	logo,	and	High-Definition	Multimedia	Interface	are	trademarks	or	registered	trademarks	of HDMI Licensing LLC. •Microsoft®, Windows®, and Windows Vista® are either registered trademarks or trademarks of Microsoft 
Corporation	in	the	United	States	and/or	other	countries. • Screenshots are used in accordance with Microsoft Corporation guidelines\
. •IBM	and	PC/AT	are	registered	trademarks	of	International	Business	Machines	Corporation. •Intel®	is	a	registered	trademark	or	a	trademark	of	Intel	Corporation	in	the	United	States	and/or	other	countries. •Apple®, Macintosh®, and Mac OS® are trademarks or registered trademarks of Apple Inc. in the United 
States	and/or	other	countries. • Other model names, company names, and product names listed in these oper\
ating instructions are 
trademarks or registered trademarks of their respective companies.
 •This product is licensed under the AVC Patent Portfolio License for the personal and non-commercial 
use of a consumer

, and no license is granted or shall be implied for any use other than t\
he personal uses 
detailed below.
-
 To encode video in compliance with the A

VC standard (“AVC Video”)
-
 To decode A

VC Video that was encoded by a consumer engaged in a personal and non-commer\
cial 
activity
-
 To decode A

VC Video that was obtained from a video provider licensed to provide AVC Video 
Additional
	information	may	be	obtained	from	MPEG	LA,	LLC	(http://www.mpegla.com).
- Separate license contracts must be obtained from MPEG LA where SD Memory Cards containing 
information recorded with this product are to be distributed to end user\
s for commercial purposes. “End 
user”
	refers	to	persons	or	organizations	handling	such	contents	for	personal	use.