Panasonic Master Setup Unit Ak Msu930p Operating Instructions

AK-MSU930P
Before attempting to connect, operate or adjust this product, please read these
instructions completely.
Master Setup Unit 

2
Safety precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, 
DO NOT REMOVE COVER (OR  BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to
persons.
The...

3
Operating precautions
≥Use the AW-PS505 dedicated AC adapter for the MSU’s power supply.
≥ ≥
Handle the unit carefully.
Dropping the unit or subjecting it to strong impact may cause malfunctioning and failures.
≥Operate the unit within a temperature range of 32 °F to 104 °F (0 °C to 40 °C).
Operation in locations below 32 °F or above 104 °F may adversely affect the internal parts.
≥Be absolutely sure to turn off the power before connecting or disconnecting the cables.
≥Do not use the unit outdoors....

4
Parts and their functions
CABLE
TALLY
CAMERA1
5600K
BLACK WHITE R B G GAMMA MATRIX FUNC SYSTEMOFF FLARE
GAMMA ONBLK
OFF GAMMA
BLK
PED GAIN GAMMA FLARE W. CLIP KNEE HD. DTL SD. DTL SD. SKINHD.SKIN
SHADING
OFF KNEE
OFF OFF HD. DTL SD. DTL
ON HD. SKIN
ON SD. SKINCLIP OFFWHITE
OFF MATRIX CHARACTERCARD
HEAD POWERALL
CLOSE BAR TESTWHITEBLACKSET UP
RESET
ALARM
REFLOCAL
STOREALL
STORE
ON
MODE
CONTROL
23456789101112131415
SD CARD
AUTO
ON
SYNCRO
HEAD
CALL
ACTIVE
M-PED IRISAU TO
LENS EXT X0. 8COASER
MEMO
RECALL...

5
Parts and their functions
3Camera selector switches [CAMERA]
These are used to select one camera and one CCU as
the pair which is to be controlled by the MSU.
A camera is selected by pressing the camera selector
switch with the same number as the camera to be
selected (its lamp will light).  The selection is released by
pressing the camera selector switch of the selected
camera (its lamp will turn off).
When a camera selector switch is pressed, the MSU
settings (such as the switch lamp lighting and...

6
5EL display
When the control item selector switches are selected, the
corresponding adjustment items and adjustment values
appear on the EL display.
Example of EL display
Parts and their functions

  H DTL
LEVEL DEP
 + CLIP
  H DTL
15  V DTL
 DARK DTL
 – CLIP
  V DTL16 CRISP
 CORNER
 CRISP7PEAK FREQ
 
PEAK FREQ4
Black shading selector switch
[BLACK SHADING CONTROL]
This is used to correct the black shading (the coloring of
black images).  When it is pressed (its lamp is lighted)
and when one of the...

7
BRIGHT:Dot matrix display brightness setting
This is used to set the brightness of the
dot matrix display.
BUZZ:Buzzer setting
This is used to set the buzzer to ON or
OFF.
:SD card read/write setting
This is used to write the camera’s data
on the SD card or read it from the card.
System switches [SYSTEM]
These are the system setting switches used to set the
down-converter mode, select the down-converter filter,
select GBR or YPbPr for the HDTV video output, select
GBR or YPbPr for the SDTV video...

8
Parts and their functions
MONI LINK:Shading link setting
This is used to set whether to link the
monitor when the R, G or B shading
switch has been selected.
ANALOG:CCU analog output setting
This is used to set the analog output of
the CCU to the HD or SD component.
SDI4 OUT:HD SDI4 output selection
This is used to set the HD SDI4 output of
the CCU as the PM or normal output.
SYNC:Sync waveform addition setting
This is used to select whether to add the
sync waveform to the analog output.
TYPE:Analog...

9
Parts and their functions
KDTL +CLP:Knee detail edge overshoot clip
This is used to limit the length of the
overshoot parts of the knee detail edge
components.
KDTL –CLP:Knee detail edge undershoot clip
This is used to limit the length of the
undershoot parts of the knee detail edge
components.
KDTL +KNE:Knee detail edge overshoot knee
This function applies the knee to the knee
detail edge overshoot parts.
KDTL –KNE:Knee detail edge undershoot knee
This function applies the knee to the knee
detail edge...

10
CRISP:Skin tone detail crisp
This is used to remove the very faint noise
components from the detail components of
the skin tone areas.
SKIN LVL:Skin detail level
This is used to set the chroma saturation of
the parts where the skin tone detail is
applied.
8Camera power switch indicator
This is the indicator of the camera’s power ON/OFF
switch.
Lights up green:The unit is communicating with the
camera.
Lights up red:The unit is not communicating with the
camera.
Flashes red:POWER OFF status established...