Panasonic Lumix Dmc gh1 Series Service Manual Repair Guide

51
9.3.15. Removal of the Mic P.C.B. and Mic
Unit
(Fig.D22) (Fig.D23) 

52
9.3.16. Removal of the Battery Spring
(Fig.D24)
9.3.17. Removal of the Battery Door Unit
(Fig.D25)
NOTE: (When Assembling)Be sure to confirm the following points when assembling.
• The Screw is tightened enough.
• Assembling conditions are fine. (No distortion, no illegal- space.)
• No dust and/or dirt on every Lens surfaces.
• LCD image is fine. (No dust and dirt on it, and no gradient images.) 

53
9.4. Disassembly and Assemble Procedure for the Lens
Refer to the following table and the illustration for disassembly and assembly.
NOTE:
1. To keep maintaining the dustproof environm ent, it is recommended dealing with Clean box.
(Refer to “ 8.2. Clean Box “
 which is found in section 8.Servi ce Fixture & Tools of this manual.)
2. Do not allow dirt and dust to get in to the inside part/component of the unit.
3. Do not touch the surface of t he lens glasses with your fingers.
4. Blow off the dust on...

54 

55
10 Measurements and Adjustments
10.1. Matrix Chart for Replaced Part and Necessary Adjustment
The relation between Replaced part and Necessary Adjustment is shown in the following table.
When concerned part is replaced, be sure  to achieve the necessary adjustment(s).
As for Adjustment condition/ procedure, consult the “Adjustment Manual” wh ich is available in Adjustment software.
The Adjustment software is available at “T SN Website”, therefore, access to “TSN W ebsite” at “Support Information from...

56
* There are no LCD / LVF adjustment model. 

57
11 Maintenace
11.1. Notice in external cleaning
11.1.1. ABOUT THE BODY
NOTE:Before cleaning the camera, remove the battery and/or disconnect power plug from the outlet.
Also, remove the SD Memory card and lens unit. 
11.1.1.1. DUST/DIRT ON TH E OUTER CASING PART (S)
1. Blow off the dust first, then sweep out the dust  from narrower spaces with soft cleaning brush.
2. Wipe up fingerprint and/or dirt on the Outer  casing part with the dry fuzz-free cloth.
11.1.1.2. DUST/DIRT ON THE IMAGE SENSOR
1. Blow...

58
11.1.2. ABOUT THE LENS
11.1.2.1. DUST/DIRT ON THE OUTER CASING PART(S)
1. Blow off the dust first, then sweep out the dust from narrower spaces with soft cleaning brush.
2. Wipe up the Outer casing part with the dry fuzz-free cloth.
11.1.2.2. DUST/DIRT ON THE LENS GLASSES
• Define the location of the dust/dirt first, whether it is outside lens surface or not. 1. When it is outside surface of the lens:• When the dust and/or dirt gets on the outer side sur-face of the Lens glasses, order the following...

59
11.3. Method of cleaning inside of lens (H-VS014140: Included in DMC-GH1K)
Important:
1. When removing the 1st lens frame unit, it has to be proceed inside of satisfied clean level.
(Less than class 10,000 Federal Standard 209D) 
As for clean box, refer to the 8.2. CLEAN BOX, in details.
2. When tighten the screws (A), use torque dr iver (RFKZ0456) with specified torque. 
3. To keep the Lens performance, use only the 1st  lens frame unit which was fitted as it was.
Therefore, the 1st lens frame uni t...

60
11.3.1.3. Removal of the food adaptor
1. Removal the 3 screws (B) and then remove the foodadaptor.
11.3.1.4. Removal of a dust /dirt
1. Blow off the dust on the Lens glass surface with theBlower, gently.
(Do not Blow too strongly.)
2. Although after blowing, the dust/dirt does not blow off, wipe out the dirt on the lens glass surface with Lens
cleaning KIT (VFK1900BK) 
(Consult the Instruction sheet which is included in the
Lens cleaning KIT in details.)
11.3.2. Assembly procedure
11.3.2.1....