Home > Panasonic > Digital Camera > Panasonic Lumix DMC FX5 User Manual

Panasonic Lumix DMC FX5 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Panasonic Lumix DMC FX5 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Playback (advanced)
    91
    4Shift the picture and press the 
    shutter button fully to set.
    5Select [YES] or [NO] and set it.
     When you select [YES], the picture 
    is overwritten.
     When the original picture is 
    protected, you cannot overwrite the 
    trimmed picture.
     Close the menu by pressing the 
    [MENU] button 2 times after 
    finishing the trimming.
    ¬Suggestions/Tips ¬
     The following pictures cannot be 
    trimmed.
    – Pictures equal to or smaller than 
    640k480 pixels
    – Pictures recorded with setting the 
    picture size to [HDTV]
    – Motion images
    – Flip animation
    – Pictures with audio
    – Rotated pictures (You can trim them 
    if you rotate them back.)
     It may not be possible to trim pictures 
    recorded with other equipment.
     The picture size of the trimmed 
    pictures may become smaller than that 
    of the original one depending on the 
    cut size.
     The picture quality of the trimmed 
    picture may be deteriorated.
    SETREVIEW
    WB
    TRIMMING
    TRIM:SHUTTER
    1600
    1/19
    EXITMENU
    100_
    0001
    ZOOM
    DELETE ORIGINALPICTURE?
    YESNO
    SETREVIEW
    WB
    SETREVIEW
    WB
    TRIMMING
    SETSELECTCANCELMENU
    FX5_FX1-PP.book  91 ページ  2003年12月15日 月曜日 午後1時27分
    Downloaded From camera-usermanual.com Panasonic Manuals 
    						
    							Playback (advanced)
    92
    Formatting the Card
    Preparation
     Set the mode dial to [ ]. (P29)
    1Select [FORMAT].
    2Select [YES] to format.
    ¬Suggestions/Tips ¬
     Usually, it is not necessary to format 
    the card (initializing). Format the card 
    when the message [MEMORY CARD 
    ERROR] appears.
     If the card has been formatted by a PC 
    or other equipment, format the card on 
    the camera again.
     After formatting, recorded pictures and 
    any other data cannot be recovered.
     If the card is formatted all images 
    and data will be permanently 
    erased. They cannot be reclaimed. 
    If any important pictures are on the 
    card, please copy them to your PC 
    before proceeding.
     During formatting, do not turn the 
    camera off.
     When the remaining battery power 
    (P13) is low, use the AC adaptor.
     If the card is protected, you cannot 
    format the card.
     If the card cannot be formatted, 
    consult your nearest servicenter.
    SETREVIEW
    WBMENU
    SETREVIEW
    WB
    PLAY2/2/2SETUP
    TRIMMINGRESIZE
    FORMAT
    EXITSETSELECTMENU
    SETREVIEW
    WB
    SETREVIEW
    WB
    DELETE ALL DETAON THE MEMORY CARD?
    YESNO
    FORMAT
    SETSELECTFor USA assistance, please call: 1-800-272-7033 
    or send e-mail to : [email protected]
    For Canadian assistance, please call:
    1-800-561-5505 or visit us at www.panasonic.ca
    FX5_FX1-PP.book  92 ページ  2003年12月15日 月曜日 午後1時27分
    Downloaded From camera-usermanual.com Panasonic Manuals 
    						
    							Playback (advanced)
    93
    Playing Back Pictures with a TV Screen
    ªPlaying back pictures with AV cable (supplied)
     Turn the camera and the TV off.
    1Connect the AV cable to the
    [AV OUT] socket of the camera.
     Align the [2] mark on the AV cable 
    and the [1] mark on the [AV OUT] 
    socket.
    2Connect the AV cable to the video 
    input and the audio input sockets 
    of the TV.
     Yellow: to the video input socket
     White: to the audio input socket
    3Turn the TV on and select external 
    input.
    4Turn the camera on and then set 
    the mode dial to playback mode 
    [].
    ªViewing pictures in other 
    countries
    When setting [VIDEO OUT] on the 
    menu, you can view pictures on a TV in 
    other countries (regions) which use the 
    NTSC or PAL system.
     Even if you set menu selection for 
    [VIDEO OUT] to [PAL], the output 
    signal is still NTSC in the recording 
    mode.
    ªPlayback pictures on TV with an 
    SD Memory Card slot
    An SD Memory Card can be played 
    back on TVs with an SD Memory Card 
    slot.
    If you play back pictures recorded using 
    [HDTV] mode on a High-Definition TV, 
    (HDTV has 16:9 aspect) the picture 
    quality will be higher.
    ¬
    Suggestions/Tips ¬
     When connecting to a TV, we 
    recommend using the AC adaptor as 
    the power source.
     Use the supplied AV cable only.
     Read the TV operating instructions too.
    DIGITAL
    DC IN
    EXT.
    AV  O U T1
    2
    FX5_FX1-PP.book  93 ページ  2003年12月15日 月曜日 午後1時27分
    Downloaded From camera-usermanual.com Panasonic Manuals 
    						
    							Playback (advanced)
    94
    Before Connecting with USB Connection 
    Cable
    Select the USB communication system according to the OS of your PC or your 
    printer before connecting them to the camera with the USB connection cable 
    (supplied).
    Set the items on [USB MODE] in the [SETUP] menu. (P25)
    1Select [USB MODE].
    (In the recording mode)2Select [Mass Storage] or [PTP].
    RECSETUP3/3
    LANGUAGEENGUSB MODE
    EXITSET SELECTMENU
    MENU
    SETREVIEW
    WB
    SETREVIEW
    WB
    SETREVIEW
    WB
    USB
    SETREVIEW
    WB
    SETREVIEW
    WB
    SETSELECT
    Mass StoragePTP
    USB MODE
    USBDirect-PrintPictBridge
    USB modePC to be connectedPrinter to be 
    connected
    Mass Storage
    (USB Direct-Print)Windows
    ® XP Home Edition, 
    Windows XP Professional, 
    Windows 2000 Professional, 
    Windows Me, Windows 98/98 SE or 
    Mac OS X (10.1 or above), 
    Mac OS 9.xPrinters supporting 
    USB Direct-Print.
    PTP
    (PictBridge)Windows XP Home Edition, 
    Windows XP Professional or 
    Mac OS XPrinters supporting 
    PictBridge.
    FX5_FX1-PP.book  94 ページ  2003年12月15日 月曜日 午後1時27分
    Downloaded From camera-usermanual.com Panasonic Manuals 
    						
    							
    Playback (advanced)
    95
    ªWhen using Windows 2000 Professional, Windows Me, 
    Windows 98/98 SE or Mac OS 9.x
    • When connecting the camera to a PC, do not set [USB MODE] to [PTP]. (When the camera is shipped, [Mass Storage] is selected.)
     When using Windows 98/98 SE, install the USB driver before connecting. (When 
    using Windows Me/2000/XP, Mac OS 9.x and Mac OS X, you do not have to install 
    the USB driver.)
     When connecting to a PC which includes the 
    above-mentioned OS with setting the [USB MODE] to [PTP], 
    the messages shown on the right appear on the LCD 
    monitor of the camera.
    The following messages appear for each OS on the display of the PC. Select 
    [Cancel] to close the window and disconnect the PC.
    PTP
    USB MODE
    OSMessage
    Windows 2000 Professional [Welcome to the Found New Hardware  Wizard]
    Windows Me
    Windows 98/98 SE [New Hardware Found]
    >
    [Add New Hardware Wizard]
    (When you connect to the PC more than 
    2 times, only [Add New Hardware Wizard] 
    appears.)
    Mac OS 9.x [Software needed for the USB device  “DMC-FX5” is not available. Would you like to 
    look for the software on the Internet?]
    FX5_FX1-PP.book  95 ページ  2003年12月18日 木曜日 午後12時16分
    Downloaded From camera-usermanual.com Panasonic Manuals 
    						
    							Playback (advanced)
    96
    Connecting to a PC (Mass Storage)
    1Turn the camera on and then set 
    [USB MODE] to [Mass Storage]. 
    (P94)
    2Connect the camera to a PC via 
    the USB connection cable 
    (supplied).
    [Windows]
    The drive appears on the 
    [My Computer] folder.
     If it is the first time for you to 
    connect the camera to a PC, the 
    required driver is installed 
    automatically so that the camera 
    can be recognized by the Windows 
    Plug and Play, then it appears on 
    the [My Computer] folder.
    [Macintosh]
    The drive is shown on the screen.
    ¬Suggestions/Tips ¬
     The flash/access indicator lights 
    during communication.
     When connecting to a PC, we 
    recommend using the AC adaptor as 
    the power source.
     If the remaining battery power 
    becomes low during communication, 
    the status indicator blinks and the 
    alarm beeps. In this case, stop the 
    communication. Then turn the camera 
    off and charge the battery.
     Use the supplied USB connection 
    cable only.
    DIGITAL
    DC IN
    EXT.
    AV  O U T
    ACCESS
    FX5_FX1-PP.book  96 ページ  2003年12月15日 月曜日 午後1時27分
    Downloaded From camera-usermanual.com Panasonic Manuals 
    						
    							Playback (advanced)
    97
    Connecting to a PC (PTP)
    Do not follow the setting below on the OS except for Windows XP and Mac OS X.
    1Turn the camera on and then set 
    [USB MODE] to [PTP]. (P94)
    2Connect the camera to a PC via 
    the USB connection cable 
    (supplied).[Windows]
    The camera icon appears on the 
    [My Computer] folder.
     If it is the first time for you to 
    connect the camera to a PC, the 
    required driver is installed 
    automatically so that the camera 
    can be recognized by the Windows 
    Plug and Play, then the camera 
    icon appears on the [My Computer] 
    folder.
    [Macintosh]
    You can read pictures with image 
    capture or iPhoto.
    DIGITAL
    DC IN
    EXT.
    AV  O U T
    ACCESS
    FX5_FX1-PP.book  97 ページ  2003年12月15日 月曜日 午後1時27分
    Downloaded From camera-usermanual.com Panasonic Manuals 
    						
    							Playback (advanced)
    98
    ¬Suggestions/Tips ¬
     Refer to P95 carefully when connecting to the OS except for Windows XP and Mac 
    OS X with setting [USB MODE] to [PTP].
     The flash/access indicator lights during communication.
     When connecting to a PC, we recommend using the AC adaptor as the power 
    source.
     If the remaining battery power becomes low during communication, the status 
    indicator blinks and the alarm beeps. In this case, stop the communication. Then 
    turn the camera off and charge the battery.
     It may take time to display the communication screen depending on the PC.
     You can only load pictures from the camera and cannot write them on the card or 
    delete them.
     Use the supplied USB connection cable only.
     When there are 1000 or more pictures on the card, the pictures may not be 
    imported.
     When the PC recovers from the standby mode while connecting it to a camera 
    with USB connection cables, they may not properly communicate with each other.
    FX5_FX1-PP.book  98 ページ  2003年12月15日 月曜日 午後1時27分
    Downloaded From camera-usermanual.com Panasonic Manuals 
    						
    							Playback (advanced)
    99
    Connecting to a Printer
    By connecting the camera directly to a printer supporting PictBridge or USB 
    Direct-Print via the USB connection cable (supplied), you can select the pictures to 
    be printed or start printing.
    1Turn the camera on and then set 
    the [USB MODE] to [PTP] 
    (PictBridge) or [Mass Storage] 
    (USB Direct-Print). (P94)
    2Turn on a printer.
    3Connect the camera to the printer 
    via the USB connection cable 
    (supplied).
    ¬Suggestions/Tips ¬
     Ask the manufacturer of the printer 
    about the corresponding models. 
    (Read the printer operating 
    instructions too.)
     If the remaining battery power 
    becomes low during communication, 
    the status indicator blinks and the 
    alarm beeps. In this case, stop the 
    communication. Then turn the camera 
    off and charge the battery.
     When connecting to a printer, we 
    recommend using the AC adaptor as 
    the power source.
     Disconnect the USB connection cable 
    and DC cable after printing.
     Use the supplied USB connection 
    cable only.
    DIGITAL
    DC IN
    EXT.
    AV  O U T
    FX5_FX1-PP.book  99 ページ  2003年12月15日 月曜日 午後1時27分
    Downloaded From camera-usermanual.com Panasonic Manuals 
    						
    							Playback (advanced)
    100
    Using a Printer (PictBridge)
    Preparation
     Connect the camera to a printer. (P99)
     Set the paper size and print quality. (Read the printer operating instructions.)
    ªSingle picture
    1Select [SINGLE PICTURE].
     The screen shown in step 2 
    appears when DPOF print is not 
    set or the printer does not support 
    DPOF print.
    2Select the picture to print.
    3Select [YES] and print.
     Press the [DISPLAY] button to print 
    the date. (Only when connecting to 
    the printer supporting to printing 
    the date.)
    Press 3 and then press 2/1 to 
    set the number of prints. Press 4 
    to print pictures.
     Press the [MENU] button to cancel 
    printing.
    SINGLEPICTUREDPOFPICTURE
    SETSELECT
    PictBridge
    SETREVIEW
    WB
    SETREVIEW
    WB
    PRINTSELECT
    1600
    100_00011/19
    PLEASE SELECTTHE PICTURE TO PRINT
    PictBridge
    SETREVIEW
    WB
    SETREVIEW
    WB
    1/191/191/19
    PLS CHECK THE  PRINTERSTART PRINTING?
    DATEDISPLAYSELECTSET COUNTSET
    COUNT1
    YESNO
    PictBridge
    SETREVIEW
    WB
    SETREVIEW
    WB
    FX5_FX1-PP.book  100 ページ  2003年12月15日 月曜日 午後1時27分
    Downloaded From camera-usermanual.com Panasonic Manuals 
    						
    All Panasonic manuals Comments (0)

    Related Manuals for Panasonic Lumix DMC FX5 User Manual