Panasonic Lcd View Finder Ak Hvf70 Operating Instructions

							1011
How to use on-screen menus (continued)
z
z MARKER menu
_indicates factory default settings.
Item Set value Remarks
MARKER
OFF ON Determines whether markers will be 
displayed in the viewfinder.
OFF 
:  Not displayed
ON  :  Displayed
ZONE
OFF 4:3
13:9
14:9
CNSCO2.39
CNSCO2.35 2:1
VISTA 95%
93%
90%
88%
80%
USER85% Selects the type of marker.
OFF 
: No marker display
4:3  : 4:3 size marker
13:9  : 13:9 size marker
14:9  : 14:9 size marker
CNSCO2.39:  
  2.39 : 1 size marker
CNSCO2.35:  
  2.35 : 1 size marker
2:1  : 2:1 size marker
VISTA  : 
  1.85:1 size marker
95%  : 95% area marker
93%  : 93% area marker
90%  : 90% area marker
88%  : 88% area marker
80%  : 80% area marker
USER85%:  
    Can be set in 1% increments 
in the 80% to 100% range 
*1 
(default  setting is 85%)
4:3
OFF
95%
93%
90%
88%
80%
USER85% Use this to select the type of marker 
displayed in 4:3 video aspect ratio
OFF 
: No marker display
95%  : 95% area marker
93%  : 93% area marker
90%  : 90% area marker
88%  : 88% area marker
80%  : 80% area marker
USER85%:  
    Can be set in 1% increments 
in the 80% to 100% range 
*1 
(default  setting is 85%)
BACK
NORMAL HALF
BLACK Sets the background brightness 
outside the marker set in the ZONE 
item.
NORMAL
 :  Normal background
HALF  :  50% background 
brightness
BLACK  :  0% (black) background 
brightness
CENTER
OFF ON Sets the center marker display.
OFF 
: Not displayed
ON  : Displayed
CROSS HATCH
HIGH LOW OFF Sets the cross hatch grid display and 
its density.
HIGH 
:  Displays a bright cross hatch 
grid
LOW  :  Displays a dim cross hatch 
grid
OFF  : Not displayed
SIZE
60
30 Selects size of cross hatch.
60 
: 60 dots and 60 lines
30  : 30 dots and 30 lines
*1    Press the SELECT dial and wait until the set value changes to light 
blue to change it.
z
z FUNCTION menu
_indicates factory default settings.
Item Set value Remarks
FUNCTION1SCAN
WFM
MARKER
PIXEL TO PIXEL FOCUS-IN-REDCROSS HATCH MONO
UNDEFSelects functions assigned to the [F1] 
to [F3] function buttons.
SCAN: 
    Switches between underscan and 
normal display
WFM: 
    Shows the waveform display 
screen
MARKER:  
    Displays the marker
PIXEL TO PIXEL:  
    Turns the PIXEL TO PIXEL 
function ON or OFF
*1*2
FOCUS-IN-RED: 
   Turns ON or OFF the function that 
highlights in red the portion of the 
image that is in focus. 
*1 *3
CROSS HATCH: 
   Turns ON or OFF the cross hatch 
grid display
MONO: 
    Switches between color and 
monochrome display
UNDEF: 
    Does not assign a function
FUNCTION2SCAN
WFM
MARKER
PIXEL TO PIXEL FOCUS-IN-REDCROSS HATCH MONO
UNDEF
FUNCTION3SCAN WFM
MARKER
PIXEL TO PIXEL FOCUS-IN-REDCROSS HATCH MONO
UNDEF
FUNCTION 
DISPLAYOFF
ON1
ON2Selects the display settings and 
action settings (1 touch, 2 touches, 
OFF) of 
functions assigned to 
function buttons [F1] to [F3].
OFF  : The function is not displayed
ON1  :  1 touch activates and displays 
operation
ON2  :  2 touches activate and display 
operation
*1    The settings are canceled when the power is turned OFF.
*2    Magnifies the center portion of the screen. The P-P mark appears at 
the top left of the screen when the function is on.
*3    During FOCUS-IN-RED operation, you can use the SELECT dial to 
change detection sensitivity.  
						

							12
How to use on-screen menus (continued)
13
z
z VIDEO CONFIG menu
_indicates factory default settings.
Item Set value Remarks
GAMMA 
SELECTSTANDARD
FILMSelects the gamma curve.
The FILM mark appears at the 
top left of the screen when FILM is 
selected.
STANDARD  : Standard mode
FILM  : Film mode
FILM GAMMAVARICAM
OTHER Selects the type of FILM gamma 
mode.
VARICAM 
:  Shows that FILM_REC 
gamma is selected on 
the camera
OTHER  :  Shows that a mode 
other than FILM_REC 
gamma is selected on 
the camera
Gamma curve (representative)
Input level
Brightness
  :OTHER
   :VARICAM
   :STANDARD
COLOR TEMP.USER 0
│
63
D93
D65
D56 Selects color temperature.
USER 0 - 63 
: 
    Adjustable settings 0 to 63 
(equivalent to a color temperature 
range of 3,000 K to 9,300 K) 
*1
D93  :
    Equivalent to a color temperature 
of 9,300 K
D65  :
    Equivalent to a color temperature 
of 6,500 K
D56  :
    Equivalent to a color temperature 
of 5,600 K
SHARPNESS 
MODEHIGH
LOW Selects the width of edges during 
contour correction (during peaking 
operation).
HIGH 
: Narrow edge
LOW  : Wide edge
SHARPNESS H0
│
30 Sets the horizontal contour correction 
value.
Adds the value to the PEAKING knob 
operation.
SHARPNESS V0
│
30 Sets the vertical contour correction 
value.
Adds the value to the PEAKING knob 
operation.
MONOOFF
ON Switches between color and 
monochrome (MONO).
OFF 
: Color
ON  : Monochrome
SCANNORMAL
UNDER Sets screen display to underscan or 
normal display.
NORMAL
 :   Normal display
UNDER  :  Underscan
*1    Press the SELECT dial and wait until the set value changes to light 
blue to change it.
z
z SYSTEM CONFIG menu
_indicates factory default settings.
Item Set value Remarks
UP TALLY 
LAMPHIGH
LOW OFF Sets the brightness of the up tally 
lamp.
HIGH 
: Lights brightly
LOW  : Lights dimly
OFF  :  Does not light the up tally 
lamp
WFMOFF
ON Displays the waveform of the 
luminance signal input to the 
viewfinder.
OFF 
: The waveform is not displayed
ON  : The waveform is displayed
WFM 
POSITIONLB
RB RT LT Selects location of WFM waveform 
display.
LB 
: Left bottom of the screen
RB  : Right bottom of the screen
RT  : Right top of the screen
LT  : Left top of the screen
z
z HOURS METER menu
_indicates factory default settings.
Item Set value Remarks
OPERATIONh 
Displays the total number of hours 
that the power has been on.
 h 
*1
LCDh 
Displays the number of hours that 
the backlight has been on.
 h 
*1
*1   
“ph” indicates the time in hours up to 262,800 hours (about 
30 years). Hours exceeding 262,800 hours are indicated as “OVER”.  
						

							1213
Table showing camera interface connector pin assignment
12910
201119Camera I/F connector (D-Sub 29-pin)
Pin No. Signal name Pin No.Signal name Pin No.Signal name
1 Y 11Y-GND 20VF P-REQ
2 Pb 12Pb-GND 21
3 Pr 13Pr-GND 22
4 14A-GND 23(P-CONT)
5 I2CDATA 15D-GND 24I2C CLK
6 R_TALLY 16 25G_TALLY
7 UP_TALLY 17UNREG-GND 26(VF-ACT)
8 18 27
9 VF12V 19F-GND 28
10 29
Appearance
Unit: mm (inch) 243.5(9-19/32)
212(8-11/32)
90(3-17/32)172(6-25/32)
85(3-11/32) 
						

							1415
Specifications
[General]
Power supply: DC 12 V (supplied by the camera)
Power consumption:  10 W
 indicates safety information.
Ambient operating temperature:
    0 °C to 45 °C (32 °F to 113 °F)
Storage temperature:
  –20 °C to 60 °C (–4 °F to 140 °F)
Ambient operating humidity:
  10% to 85% (no condensation)
Dimensions (Width   Height  Depth):
    243.5 mm  212 mm  172 mm
(9-19/32 inches   8-11/32 inches   6-25/32 inches)
(with hood attached)
    243.5 mm  212 mm  85 mm
(9-19/32 inches   8-11/32 inches   3-11/32 inches)
(without hood)
Weight:  Approx. 1.6 kg (3.53 lb) (without hood)
[Display panel]Panel size:
 7.0-inch (177.8 mm)
Number of pixels:
  1024  600 (WSVGA)
Display colors:
  Approx. 16,200,000 colors
[Switch functions and connectors]Operation panel:
   POWER switch  1
MENU button p1
SELECT dial p1
Function buttons  3
Picture adjusting knobs   3
([BRIGHT], [CONTRAST], [PEAKING])
Connectors:
    Camera I/F connector (D-Sub 29-pin  1)
Maintenance inspections
Maintenance inspections through periodic and appropriate maintenance are essential to keep the unit in optimum condition and ensure safe operation. 
Be sure to conduct maintenance inspections to enable long-term, full use of all its functions.
Necessity of periodic maintenance serviceThe LCD panel is equipped with a backlight. Performance of the backlight (a consumable component) deteriorates over time, and will eventually fail.
Therefore, service should not be left until failure occurs, but scheduled maintenance should be conducted to maintain device performance and prevent 
unexpected consumable-related failures. 
						

							1415
Memo  
						

							Information on Disposal for Users of Waste Electrical & Electronic Equipment 
(private households)
This symbol on the products and/or accompanying documents means that used electrical and electronic products 
should not be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to designated collection points, where they 
will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to 
your local retailer upon the purchase of an equivalent new product.
Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on 
human health and the environment which could otherwise arise from inappropriate waste handling. Please contact your 
local authority for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.
Декларація про Відповідність
Вимогам Технічного Регламенту Обмеження Використання деяких Небезпечних Речовин в електричному та  електронному обладнанні
(затвердженого Постановою №1057 Кабінету Міністрів України)
Виріб відповідає вимогам Технічного Регламенту Обмеження Використання деяких Небезпечних Речовин в 
електричному та електронному обладнанні (ТР ОВНР).
Вміст небезпечних речовин у випадках, не обумовлених в Додатку №2 ТР ОВНР, :
1.  свинець(Pb) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на мільйон;
2.  кадмій (Cd) – не перевищує 0,01 % ваги речовини або в концентрації до 100 частин на мільйон;
3.  ртуть(Hg) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на мільйон;
4.  шестивалентний хром (Cr
6+ ) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на мільйон;
5.  полібромбіфеноли (PBB) – не перевищує 0,1% ваги речовини або в концентрації до 1000 частин на мільйон;
6.    полібромдефенілові ефіри (PBDE) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на 
мільйон.