Panasonic Lcd Tv Dvd Video Receiver Cq Vd7200u Operating Instructions

							6556E
N
G
L
I
S
H
CQ-VD7200U
6455E
N
G
L
I
S
H
CQ-VD7200U
❏Transportation Bracket RemovalBe sure to remove the transportation brackets before use (installation).
Use Binding-Head Screws (M5 x 6 mm) for installation.(apage 68)
Be careful not to lose these Binding-Head Screws.
Display Unit
Binding-Head
Screws(M5 x 6 mm)
Binding-Head
Screws(M5 x 6 mm)
Transportation
Bracket
Transportation
Bracket
Installation Guide
(continued)
❏
Connect All Leads
Now that you have identified all the wires in the car, youre
ready to begin connecting them to the LCD monitor wires.
The wiring diagram (apage 72-83) shows the proper
wiring and color coding of the leads.
We strongly recommend that you test the unit before mak-
ing a final installation.
You can set the unit on the floor and make temporary con-
nections to test the unit. Use electrical tape to cover all
exposed wires.Important: Connect the red power lead last, after youhave made and insulated all other connections.
Ground
Connect the black ground lead of the power connector to
the metal car chassis.
Speakers (not supplied speaker)
Connect the speaker wires. See the wiring diagram for the
proper hookups. Follow the diagram carefully to avoid
damaging the speakers and the stereo unit.The speakers used must be able to handle more than 45 W
of audio power. If using an optional audio power, the speak-
ers should be able to handle the maximum amplifier output
power. Speakers with low input ratings can be damaged. Speaker impedance should measure 4–8 Ω, which is typi-
cally marked on most speakers. Lower or higher imped-
ance speakers will affect output and can cause both speak-
er and stereo unit damage.
Battery
Connect the yellow battery lead to the correct radio wire or
to the battery fuse port on the fuse block. 
Equipment
Connect any optional equipment according to the instruc-
tions furnished with the equipment. Read the operating and
installation instructions of any equipment you will connect
to this unit.Power
Connect the red power lead to the correct car radio wire or
to the appropriate fuse port on the fuse block.
If the LCD monitor functions properly with all these con-
nections made, disconnect the wires and proceed to the
final installation.
❏Final Installation Lead Connections
Connect all wires, making sure that each connection is
insulated and secure. Bundle all loose wires and fasten
them with tape so they will not fall down later. Now insert
the LCD monitor into the mounting collar.
Congratulations!  After making a few final checks, you’re
ready to enjoy your new LCD monitor.❏Final Checks
1. Make sure that all wires are properly connected and
insulated.
2. Make sure that the LCD monitor is securely held in
the mounting collar. 
3.Turn on the ignition to check the unit for proper
operation.
If you have difficulties, consult your nearest authorized pro-
fessional installer for assistance.
Caution: Never ground the speaker cords. For exam-
ple, do not use a chassis ground system or a three-
wire speaker common system. Each speaker must be
connected separately using parallel insulated wires. If
in doubt about how your car’s speakers are wired,
please consult with your nearest professional installer.
❏Precautions¡Disconnect the cable from the negative (–) battery termi-
nal (see caution at right).
¡Unit should be installed in a horizontal position with the
front end up at a convenient angle, but less than 30°.This unit should be professionally installed.  In case of diffi-
culty, please consult with your nearest professional
installer.
1. This unit only operates in a 12-volt DC negative ground
system.
2. Follow the electrical connections carefully (apage 72-
83).  Failure to do so may result in damage to the unit.
3. Connect the power lead after all other connections are
made.
4. Be sure to connect the battery lead (yellow) to the posi-
tive terminal (+) of the battery or fuse block (BAT) termi-
nal.
5. Insulate all exposed wires to prevent short circuiting.
6. Secure all loose wires after installing the unit.
7. Please carefully read the operating and installation
instructions of the respective equipment before connect-
ing it to this unit.
Caution: Please follow the laws and regulations of
your state, province or country for installation of the
unit.
Caution: Various settings that have been stored in
the memory in other on-board equipment (car naviga-
tion etc.) may be lost if the battery terminals are dis-
connected.
Therefore, we recommend to make a record of or to
back up the settings before disconnecting the termi-
nals. 
After completing installation of the main unit, set the
equipment again according to the record.Cautions: 
¡We strongly recommend that you wear gloves for
installation work to protect yourself from injuries.
¡When bending the mounting tab of the mounting
collar with a screwdriver, be careful not to injure
your hands and fingers.
less than 30° 
						

							67
CQ-VD7200U
58E
N
G
L
I
S
H
(a) Using the Rear Support Strap o(b) Using the Rubber Pad r
rRubber Pad
tMounting Bolt (M5)
Display Unit
Bracket
(On car)
uWasher
Assembling 
Hex. Bolt 
(M5 x 10 mm)*1 iWasher Assembling Hex.
Bolt (M6 x 20 mm)
Fire wall of car Drill a hole 6.5 to 7 mm
in diameter.yFlange Nut
(M6)
Display Unit oRear Support Strap
Method for Fixing the Rear of the Unit
qPush the right and left clamp plates outward, one at a time, and pull the display unit toward yourself.
wAfter removing the right and left clamp plates, pull the unit with both hands till it comes off.
Push here to
remove the
clamp plates. qw
To Remove the Display Unit
*1: 
Use 
M5 x 8 mm size bolt (optional) if bolts other than
the supplied ones are to be used.
66
CQ-VD7200U
57E
N
G
L
I
S
H
Installation Guide
(continued)135624
❏Installation Procedures
(When using Mounting Collar w)
Mounting the Display Unit
Insert the Mounting Collar winto the dashboard, and
bend the mounting tabs out with a screwdriver.
Establish the rear connection of the unit.
After fixing Power Connector 
@6
and Display Unit/Hide-
away Unit Connecting Cord 
@9, fix the rear of the unit to
the car body by either method (a) or (b) shown at right. 
Insert Trim Plate q.
After installation
reconnect the negative
(–) battery terminal. Attach the Mounting Springs eto the display unit.
@6
Power Connector
@9Display Unit/Hide-away
Unit Connecting Cord
tMounting Bolt (M5)
eMounting Spring
!1Flat-Head Screw
(M5 x 6 mm)
Note: 
The car model,
installation conditions and
combination of the units
used may impose some
restrictions on opening
and closing the monitor as
well as on the angle and
position to which the
monitor can be adjusted.
Fastening the Mounting CollarThe tabs to bent vary depending on the car. Bend them
with a screwdriver to fasten the Mounting Collar 
w
securely in the dashboard.
wMounting CollarDashboard
Tab
Insert the unit into Mounting Collar w
Secure the clamp plate of Mounting Collarw
to the hook of Mounting Spring 
e.
Clamp plate 
						

							69
CQ-VD7200U
60E
N
G
L
I
S
H
Attach the seal side of the Velcro Tape 
@3
to the hide-away unit, then mount the unit
on the carpet.
Note: Some carpet materials may not be
suitable for this mounting method.  In this
case, please contact your nearest
Panasonic Servicenter for installation.❑Unit installation by using the Mounting Brackets @0and the Base Brackets @1
.
@3
Velcro Tape
!9Hex. Nut (M5)
Carpet@0
Mounting Bracket
!7Binding-Head Screw
(M5 x 8 mm)
!8Tapping Screw (ø 6 x 20 mm)@2
Double-Faced Adhesive Tape
Drill for 4.8 mm diameter holes to the chassis.
* Put the tape and the base bracket together with each hole of the tape and
bracket connected so that the screw goes in at two positions.
@1
Base Bracket Let the bolts of
the base bracket
pass the carpet.
Make cuts by
using cutter.
Note: Apply an anticorrosive to the holes and tapping screws.
❑Mount the unit on the car carpet by using Velcro Tape @3
.
Mounting the Hide-away Unit
Cautions: 
¡Never mount the unit in any of the following locations to avoid damage due to overheating;
1. Near the heater port.
2. Places like the dashboard or rear deck, where it may be exposed to direct sunlight.
¡Do not mount the unit near the door, where it could be exposed to rain.
¡Do not separate the hide-away unit.Caution: You run the risk of interfering with the mounting or causing damage by drilling into the gas tank, a wiring
harness, or other component.
68
CQ-VD7200U
59E
N
G
L
I
S
H
Before mounting the speaker, wipe water, dust and oil stains
off from the place where the speaker should be mounted to
enhance adhesive strength.
Mounting the Speaker
Speaker
!5Double-Faced
Adhesive Tape
!6Clamp
Installation Guide
(continued)
Use the supplied Spacer !3if mounting hole of your car is shaped like below.
Display Unit
!3Spacer
!4Double-Faced Adhesive Tape !0Binding-Head Screw
(M5 x 6 mm)Bracket Mounting Hole
of a Bracket
(in section)
Existing Bracket (L)
(Bracket originally attached to the car)!4Double-Faced 
Adhesive TapeExisting Bracket (R) !0Binding-Head Screw
(M5 x 6 mm)
!3Spacer
❏Installation Procedures (When not using Mounting Collar w)Use the brackets supplied with your car when mounting this unit. The bracket shape and mounting method vary with car
manufacturers, car types and manufacturing year. Please consult your nearest dealer or installer.
Select mounting screws according to the hole positions and hole shape of the bracket.
!1Flat-Head Screw (M5 x 6 mm) 4 pieces !2Binding-Head Screw (M4 x 3 mm)
4 pieces !0Binding-Head Screw (M5 x 6 mm) 2 pieces
Recycle the Binding-Head Screws that fixed the transportation brackets for two more 
positions.
When using these
mounting holes
Cautions: 
¡Do not install the speaker in a location which obstructs
operation of the air bag or other safety equipment.
¡Do not leave a credit card or other magnetic cards near
the speaker to avoid damaging the cards. 
						

							71
CQ-VD7200U
62E
N
G
L
I
S
H
Peel the sheet from the back of antenna body
and affix it. Then, affix the grounding plate on a
metal part. Insert the grounding plate into the antenna body and hold the antenna element with the Antenna Clamp 
@4.
Follow the steps below to affix the antenna securely.q 
Affix the antenna body.
w 
Straighten the antenna element and affix it.
e 
Put the Antenna Clamp 
@4
on the center of the antenna element.
r 
Adjust the angle and position of the grounding plate and affix it.
Follow the steps below to install the grounding plate.q 
Insert the grounding plate into the antenna body.
w 
Hold the grounding plate with the terminal cover.
e 
Screw the grounding plate.
r 
Hold the antenna element with the Antenna Clamp 
@4.
Select a suitable screw point for
the grounding plate to adhere to a
metal part and remove the screw
and the terminal cover.
For some models, you cannot straighten
the longer element.
No bendingComfortably curving
2
3
Caution: 
Be sure to connect
the grounding plate. Otherwise,
desensitization will be caused.
rr qe
w
ScrewTerminal cover
InsertGrounding
Plate
Screw
points
Cautions: 
¡Avoid contacting the adhesive surface.
¡Do not re-adhere to avoid weakening adherability.
¡Avoid adhering on the heating wire as much as possible.r
qw
e
we
Adjust
Cord routing
Route the cord behind the
rear seat and affix it with
adhesive tape.
Hold the cord with
a Cord Clamp 
@5.
Route the cord inside the
upholstery and under the
carpet.
Some models restrict the installa-
tion of the TV antenna due to rear
window size or open/close of the
hatch. Contact your dealer.
4
For a hatchback type: Stick the grounding plate skillfully and hold the
loose antenna element with the Antenna Clamp 
@4
so that the element will not become caught in the
hatchback door. Adjust the cord length so that the
cord does not interfere with the movement of the
hatchback door, and secure the cord with Cord
Clamp 
@5.
70
CQ-VD7200U
61E
N
G
L
I
S
H
Installation Guide
(continued)
Mounting the TV Antenna
Antenna cable identification
0.5A
ACC 0.5A
Cautions: 
¡Be sure to install the TV antenna on the inner side
of the rear window.
¡Be sure to connect the power lead of the TV
antenna to ACC power DC 12 V.
¡Keep the antenna away from the external amplifier
and the rear speaker cord as much as possible.
5
Straighten the bent antenna element.
Confirm the adhering positions.
Affix the antenna temporarily with adhesive tape
after confirming the antenna position.1
Preparations: 
Remove the upholstery. Remove the upholstery at the both sides of the
rear window to establish a ground.
Observe the following to enhance adherability.
¡Wipe the inner surface of the rear window with a
wet and soft cloth along the heating wire. But do
not leave water droplets on the glass.
¡When the outside-air temperature is less than 68
°F (20 
°C)
, switch on the rear window defogger
or the car heater to warm the surface of the rear
window for approx. 5 minutes.
Power Lead
To ACC power,
+12 V DC.
Ground Lead
To a clean, bare
metallic part of
the car chassis.
(Red)
(Black)(Fuse 0.5 A)
Antenna Cord To TV antenna
connector on the
hide-away unit.
Shorter side 
Longer
side 
						

							73
CQ-VD7200U
64E
N
G
L
I
S
H
Speaker
(Black)
(Black/green stripe)
Hide-away Unit
(Rear)Note: 
See next page for hide-away unit
electrical connection.
Note: Supplied only for operational sound such as a beep.
Do not use it for a center speaker.Caution: Do not use the supplied speaker for some
other units or components.
72
CQ-VD7200U
63E
N
G
L
I
S
H
Panasonic
ACC
BATTERY 5AVIDEO-CONTSIDE BRAKEREVERSE
SPEAKER
!
@
Wiring DiagramElectrical ConnectionsAccessory used for wiring
(Green/yellow stripe)
@9
Display Unit/Hide-away Unit Connecting Cord
(Blue/yellow stripe)
(Violet/white stripe)
(Red)
(Black) (Yellow)(Black)
(Black/green stripe)
Side Brake (Parking Brake) Connection
Lead
Be sure to wire the side brake (parking
brake) for safety and preventing accidents.
(a
page 76)
Reverse Lead
When connecting the rear view camera,
use the reverse lead. (
a
page 81)
Power Lead
To ACC power, +12 V DC.
Battery Lead
To the car battery, continuous +12 V DC.
Ground Lead
To a clean, bare metallic part of the car
chassis.
Note: 
Use a Reverse Extension Cord 
@7
if
needed.
(Resistor 220 
Ω)
(Fuse 5 A)
Speaker Lead
Display Unit
(Rear)
@6
Power Connector
RGB Input Cord
To the RGB Connector of the Panasonic car
navigation system (available in future).
Video Control Lead
To the Video Control Lead of the
Panasonic car navigation system
(available in future).No. Item Qty@6
Power Connector (for display unit) 1
@7
Reverse Extension Cord
(for rear view camera)1
@8
Clip Connector 1
@9
Display Unit/Hide-away Unit
Connecting Cord1
No. Item Qty#0
Power Connector (for hide-away unit) 1
#1
Ground Lead 1
#2
Radio Antenna Extension Cord 1
Digital Audio Output
Connector (optical)
(a
page 82)
Caution:Do not
insert the power
connector into the
unit until the wiring
is completed.Notes: 
¡To prevent damage to the unit, be sure to follow the connection diagram below.
¡Be sure to fully plug in the connectors. Secure them with clamps and tape.
¡When game machines are connected, the picture may be unstable.
¡When removing the 
Power Connector 
@6
and Display Unit/Hide-away Unit Connecting Cord 
@9
, be sure to press the clip.
¡All other installation methods require the use of dedicated metal fittings. Consult with a qualified servicing engineer or your
dealer if other methods are required.
Cautions: 
¡This unit is designed for use in a car having a 12-volt negative ground battery system.
¡Be sure to insulate any exposed wires from a possible short-circuit from the car chassis. Bundle all cables and keep
cable terminals free from touching any metal parts.
¡Note that if your car has a driving computer or a navigation computer, disconnecting the cable from the battery may
clear the memory.
¡Install the cords avoiding the spots where the temperature should be extremely high. 
						

							BATTERY 15A 
ACC
TWIN CD  C-CONTAMP-CONT MAX 0.1ANAVI MUTEANT-CONT MAX 0.1A
!
@
!
@
!
@
!
@
REAR RFRONT LFRONT RREAR L
75
CQ-VD7200U
66E
N
G
L
I
S
H
(Rear)
(Front)
(White/black stripe)
(Gray/black stripe)
(Green/black stripe)
(Violet/black stripe)(White)
(Gray)
(Green)
(Violet)
(Left)
(Right)
(Left)
(Right)To Front
Speaker
To Rear
Speaker 
Pre-Out Connector (Front)
Pre-Out Connector (Rear)
Subwoofer Output Connector (Mono)CD Changer Control Connector
(CD
•C-IN) (
a
page 78, 79
) Video Input Terminal 1 (VTR1-IN)
Video Input Terminal 2 (VTR2-IN)
Connect a VCR, camcorder, rear view camera, other
brand’s car navigation system, etc. (
a
page 80-83)
Video Output Terminal (VIDEO-OUT)
Connect the rear monitor. (a
page 80) Ground Terminal
Power Connector
Radio Antenna Connector (RADIO ANT IN)
Note: 
Use the Radio Antenna Extension
Cord #2 
if necessary.
To external amplifier
Display Unit/Hide-away Unit Connector
TV Antenna Connector
(TV ANT IN) 
74
CQ-VD7200U
65E
N
G
L
I
S
H
Electrical Connections
(continued)
#1
Ground Lead 
To a clean, bare metallic part
of the car chassis
Dual CD Changer Control Lead
External Amplifier Control
Power Lead
To an external amplifier.
Battery Lead
To the car battery, continuous
+12 V DC.
Power Lead
To ACC power, +12 V DC.
Ground Lead
To a clean, bare metallic part
of the car chassis.
(Orange)
(Blue)
(Brown/white stripe)
(Blue/white stripe)
(Yellow)
(Red)
(Black)(Resistor 220 
Ω) (Fuse 15 A)
#0  
Power Connector
Rear Speaker Lead(Right) Front Speaker Lead(Left)
Front Speaker Lead(Right)
Rear Speaker Lead(Left)
Hide-away Unit
(Rear)
@9
Display Unit/Hide-away
Unit Connecting Cord
TV Antenna 
Refer to “Mounting the TV Antenna” 
for TV antenna connection. 
(a
page 70)
Motor Antenna Relay Control Lead
(To motor antenna) (Max. 0.1 A)
This lead is not intended for use 
with a switch actuated power antenna.
Note: 
The power antenna extends automatically
when the radio mode is selected.
Navi Mute Lead 
Connect to the Navi Mute Lead
of the Panasonic car navigation
system (available in future). 
						

							77
CQ-VD7200U
68E
N
G
L
I
S
H
76
CQ-VD7200U
67E
N
G
L
I
S
H
Electrical Connections
(continued)
—
+
SIDE  BRAKE
Caution: For safety, be sure to ask your nearest professional installer to do this connection.
The side brake (parking brake) switch position varies with the car model.
For details on the exact location of the side brake (parking brake) switch
in your car, contact your dealer.
qAttach a Clip Connector 
@8
to the end of the side
brake (parking brake) connection lead.
w
The Clip Connector 
@8
is connected to the power
source side lead of the side brake (parking brake)
lever.
Connecting the Side Brake (Parking Brake) Connection LeadSide brake (Parking brake)
Foot brakeSide Brake (Parking Brake) Connection
Lead(Blue/yellow stripe)
When the side brake (parking brake) lever is
engaged, the unit is grounded by the chassis.
Side brake (parking brake) switch
Car chassis Battery Brake light
@8
Clip Connector
Side Brake (Parking Brake)
Connection Lead
(Blue/yellow stripe)
Comes up to this point.
Power source side lead
Color of the Connectors
Color of the connectors used for the connections in
pages 78-83.
White Red
Yellow
(Not used) 
						

							7970E
N
G
L
I
S
H
CQ-VD7200U
7869E
N
G
L
I
S
H
CQ-VD7200U
Electrical Connections
(continued)
Connection with Dual CD Changer Selector (CA-CD55)
CD·C-1CD·C-2
TWIN CD·C-CONT
CD changerCX-DP880U(option)
DIN Cord
(Supplied to CA-CD55)
RCA Cord
(Supplied to CA-CD55)
Clip connector
(Option)
(L) (White)(L)
(White)
(L)
(White) (L) (White)(R) (Red)
(R)
(Red)(R)
(Red)
DIN Cord
Battery Lead(Yellow)
To the car battery,
continuous +12 V DCGround Lead(Black)
To a clean, bare metallic part of the car chassis
RCA Cord Power Connector
(Supplied to CX-DP880U)
Dual CD Changer
SelectorCA-CD55(option)
Battery Lead(Yellow)
To the car battery, continuous
+12 V DC Ground Lead(Black)
To a clean, bare metallic part of the car chassis
CD changerCX-DP880U(option)
DIN Cord RCA Cord
Power Connector
(Supplied to CX-DP880U) Power Connector
(Supplied to CX-DP880U)
CQ-VD7200U
Hide-away Unit 
(Front)
(R) (Red)
CD changerCX-DP880U(option)
Battery Lead(Yellow)
To the car battery, continuous +12 V DC Ground Lead(Black)
To a clean, bare metallic part
of the car chassis
CQ-VD7200U
Hide-away Unit 
(Front)
DIN Cord
(R) (Red)
(L) (White)
Connection with CD Changer (CX-DP880U) 
Note: Refer to the operating instructions for the connected devices, in addition.Note: Refer to the operating instructions for the connected devices, in addition. 
						

							PRN
D
2
L
Panasonic
REVERSE
Connecting the Reverse LeadIf using an optional rear view camera, the reverse lead must be
connected.
Connect the reverse lead (violet/white stripe) to the positive (+)
lead of the reverse lamp (the lamp with a clear lens that lights
when the transmission gear is shifted into the reverse position).
Notes: 
¡Connect the reverse lead after cutting the terminal at the end.
¡Use a Reverse Extension Cord @7if needed.
Connection with Rear View Camera
Note: Refer to the operating instructions for the connected devices, in addition.
Rear View Camera 
(option)
(Video)
(Yellow)
RCA Cord(Option)
Rear View Camera
Control Unit 
(option)
Hide-away Unit
(Front)CQ-VD7200U
Display Unit (Rear)
(Video)
(Yellow)
@6 
Power Connector
Check the reverse lamp.
Take it out of the back of
the tail lamp mount.
Reverse lamp
Clip connector
(Option)BatteryCar chassis
Transmission gear
Cut here.
Reverse Lead(Violet/white stripe)Camera Input
808171E
N
G
L
I
S
H
72E
N
G
L
I
S
H
CQ-VD7200U
CQ-VD7200U
Electrical Connections
(continued)
Audio
Left
Right Video
output
INTELLIGENT SYSTEM
BS G-CODE
POWER
Connection with VCR or Camcorder
Note: Refer to the operating instructions for the connected devices, in addition.
VTR1-IN
Connection with Rear Monitor
Note: Refer to the operating instructions for the connected devices, in addition.CQ-VD7200U
Hide-away Unit
(Front)
(R)
(Red)
(L)
(White) (Video)
(Yellow)
VCR 
(option)
Camcorder 
(option)
(R)
(Red)
(L)
(White)
(R)
(Red)
(L)
(White) (Video)
(Yellow)
RCA Cord(Option)
CQ-VD7200U
Hide-away Unit
(Front)
Over-head Monitor
CY-VMX6800U
(option)
RCA Cord(Option)
(Video)
(Yellow) (R)
(Red)
(L)
(White)
(Video)
(Yellow) 
						

							828373E
N
G
L
I
S
H
74E
N
G
L
I
S
H
CQ-VD7200U
CQ-VD7200U
REAR
FRONT
ANALOG-INSUB·W
4063$&
4&
-7
0-
406
3$
&


%3

$
0.1104*41
$%
*.
.
65
&
$

TVQFS

CSJHIU

NVMUJDPMPS

EJTQMBZ



X

1PXFS


NQMJGJFS

GPS
$FOUFS

4QFBLFS
%
*(*
5
-1
30

-0(
*$
%
*(
5-

4
6
3306
/%
1
3
0$
&440
3
10
4*5
*
0/
%*.
.&3 4
1$
&
183
!
@
CENTER
Panasonic
AMP-CONT MAX 0.1A
DIGITAL-IN
(Right)
(Left)
Front Speaker Rear Speaker  CY-M7052 (Option)
(Top)
Center Speaker
EAB-CF2Subwoofer
(Black/green
stripe)(Black)
Center Speaker Lead
RCA Cord(Option)
(When a two-way cord is used) Power Connector
(Supplied to CY-AC300)
#0
Power Connector
(Rear) CQ-VD7200U
Hide-away Unit
(Front)
(L)(R)
(L)(R)
(L)(R)
(R)
Digital Surround Processor
CY-AC300
Operating Unit 
(option)
Digital Surround Processor
CY-AC300
(Rear)
(Front)
Operating Unit/Main Unit
Connecting Cord
(Supplied to CY-AC300)
CQ-VD7200U
Display Unit (Rear)
Note: Refer to the operating instructions for the connected devices, in addition.
Notes on handling optical fiber cable: 
¡Do not allow the cable to be dam-
aged by getting it caught in the door,
placing a heavy object on it, etc.
¡Make sure that the cable is not
strained when it is connected.
¡Do not bend the cable sharply.
25 mm or more
Optical Fiber Cable
(CA-LRD60: Option)
@9
Display Unit/Hide-away Unit Connecting Cord
@6
Power Connector
RCA Cord
(Option)
Connection with Digital Surround Processor (CY-AC300)
(Left)(Right) CY-M9054 (Option)
(Top)
Amplifier Control Power
Cord(Blue/white stripe)
Amplifier Control Power
Cord(Blue/white stripe)
(Connect to AMP-CONT)
RCA Cord
(Option)
(L)(White) (R)(Red)
(R)(Red) (L)(White)
(R)(Red) (L)(White)
External Amplifier
Control Power Cord
(L)(White)
(R)(Red)
Electrical Connections
(continued)
Digital Audio Output
Connector (optical)