Panasonic LCD Projector Pt Tw343 Operating Instructions

							ENGLISH - 41
 
buttons
1) Press the  or < D.ZOOM -> button on the remote control.
 fThe [D. zoom] individual adjustment screen is displayed.
 fPress asqw on the remote control to move the display position during zoom in. 
[D.zoom] individual adjustment 
screenOperationAdjustmentAdjustment range
Press the  button.Increases magnification.0 ~ 33Press the  button.Decreases magnification.
While the screen is displayed and the 
image is expanded.
Press the as buttons.Moves the area to the top 
or the bottom.--
Press the qw buttons.Moves the area to the left 
or the right.
Note
 fWhen the input signals change during [D. zoom], the adjusted value of the digital zoom will be cancelled.
 fWhen no signal input, the key operation is invalid and the icon  will appear.
 fYou can also press asqw buttons on the control panel to move the display position during zoom in.
Controlling the volume of the speaker
You can adjust the volume of the audio output from the build-in speaker and the  terminal.
buttons
1) Press the  or  button on the remote control.
Increases the volume.
Decreases the volume.
Switching the image mode
This function allows you to switch the image mode.
button
1) Press the  button on the remote control.
 fIt will switch each time you press the button, [Dynamic] → [Standard] →[Cinema] → [Blackboard(Green)] → 
[Colorboard] → [User image] → [Dynamic] →....
Note
 fFor details, please refer to the [Color adjust] menu → [Image mode] (x page 52).
Using the mute function
The audio from the built-in speaker or  terminal will be turned off temporarily.
button
1) Press the  button on the remote control. 
 fThe audio turns off.
2) Press the  button again.
 fThe audio turns on.
Chapter 3   Basic Operations - Basic operations by using the remote cont\
rol  
						

							42 - ENGLISH
Using the Daylight View Lite function
The Daylight View Lite function improves the vividness of the image even if it is proj\
ected under a bright light.
button
1) Press the  button on the remote control. 
 fThe Daylight View Lite function will be switched enable/disable each time you press th\
e button.
Note
 fFor details, please refer to the [Color adjust] menu → [Daylight View] (x page 54).
Setting the remote control ID numbers
When you use the system with multiple projectors, you can operate all the projectors simultaneously or each projector 
individually by using single remote control, if unique ID number is assi\
gned to each projector.
After setting the ID number of the projector, set the same ID number to the remote control.
There are seven different ID codes (ALL, Code 1~Code 6), the initial ID number is [ALL].
  
buttons
1) The ID numbers of the projector are set by pressing the  button o\
ne time to six times 
while holding down the  button. 
 fThe number of times you press the  button corresponds to the desi\
red ID code number. The number of times 
to press the  button is as follows: 
Code 1= Once, Code 2= Twice, Code 3= 3 times, Code 4= 4 times, Code 5= 5 times, Code 6= 6 times.
 fThe ID code is changed when the  button is released.
Attention
 fThe ID number set on the remote control will be stored unless it is set \
again. However, it will be erased if the remote control 
is left with dead batteries. Set the same ID number again when the batte\
ries are replaced.
Note
 fSet the ID number of the projector from the [Expand] menu → [Remote control]. (x page 69)
 fThe ID code is reset to [ALL] (default) by pressing the  button and  button at the same time for five 
seconds or more.
 fIf the  button is pressed seven times or more, the operation is i\
nvalid, the ID code cannot be changed.
Chapter 3   Basic Operations - Basic operations by using the remote cont\
rol  
						

							ENGLISH - 43
Chapter 4   Settings
This chapter describes the settings and adjustments you can make using t\
he on-screen menu.  
						

							44 - ENGLISH
Menu Navigation
The on-screen menu (Menu) is used to perform various settings and adjustments of the projector.
Navigating through the menu
Operating procedure
 
button
1) Press the  button on the remote control or the control panel.
 fThe main menu screen appears.
2) Press as to select an item from the main menu.
 fThe selected item is highlighted in orange.
3) Press the  button.
 fThe submenu is displayed, and submenu items become selectable.
(there is no lower menu under the submenu)(there is lower menu under the submenu)
 fPlease perform step 4). fIf there is lower menu under the submenu,  will be displayed. (except for [System] in [Display] menu)
 fPlease perform step 7).
4) Press as to select a sub-menu item, press the  button.
 fIf the selected submenu can be set or adjusted,  will be displayed. 
Chapter 4   Settings - Menu Navigation  
						

							ENGLISH - 45
5) Press as to switch or adjust settings.
 fSome items will switch in order as follows each time you press as.
ABC
6) Press the  button or the  button.
 fThe changed settings or the adjusted value is confirmed. 
7) Press as to select a sub-menu item, press the  button.
 fSwitches to the next layer of the menu screen.
8) Press the  button.
 fIf the selected item can be set or adjusted,  will be displayed.
9) Press as to switch or adjust settings.
 fSome items will switch in order as follows each time you press as.
ABC
 fThe selected item will be displayed in a check  mark.
10) Press the  button or the  button.
 fThe changed settings or the adjusted value is confirmed. 
Note
 fPressing the  button while the menu screen is displayed returns to the previous menu or exits the menu screen. fSome items may not be adjusted or used for certain signal formats to be \
input to the projector. The menu items that cannot be adjusted or used are shown in gray characters, and they cannot be sel\
ected.  fSome items can be adjusted even if signals are not input. fFor menu items, refer to “Main menu” (x page 45) and “Sub-menu” (x page 46).
Main menu
The following items are in the main menu.
When a main menu item is selected, the screen changes to a submenu selection screen.
Main menu itemPage
[Display]49
[Color adjust]52
[Setting]55
[Expand]59
[Memory Viewer]71
[Info.]73
Chapter 4   Settings - Menu Navigation  
						

							46 - ENGLISH
Sub-menu
The sub-menu screen of the selected main menu appears, and you can set a\
nd adjust the various items in the submenu.
[Display]  
Sub-menu itemFactory defaultPage
[Auto PC adj.]*1-49
[Fine sync]*1-49
[H Position]*1-49
[V Position]*1-50
[H.Size]*1-50
[Aspect][Normal]50
[Project way][Front]51
[Menu position][Upper left]51
[Background display][Blue]51
[System]-51
*1 Only for computer signals.
[Color adjust]  
Sub-menu itemFactory defaultPage
[Image mode][Standard]52
[Contrast][32]52
[Brightness][32]52
[Color]*1[32]53
[Tint]*1[32]53
[Color temp.]*2[Mid]53
[Red][32]53
[Green][32]53
[Blue][32]53
[Sharpness][8]54
[Daylight View][Off]54
*1  Only for video, S-video and Component signals
*2 Only for computer signals and HDMI signals
Note
 fThe factory default settings may vary depending on the image mode.
[Setting]  
Sub-menu itemFactory defaultPage
[On start][Off]55
[Standby mode][Eco]55
[High land][Off]55
[Lamp control][  (Normal)]56
[Cooling fast][Normal]56
[Closed caption][Off]56
[Key lock][  (Off)]57
[Iris][On]57
[Sound]-57
[HDMI Setup]-58
[Expand]  
Sub-menu itemFactory defaultPage
[Language][English]59
[Auto setup]-59
Chapter 4   Settings - Menu Navigation  
						

							ENGLISH - 47
Sub-menu itemFactory defaultPage
[Keystone][Store]61
[Logo]-63
[Security]-65
[Power management][Shut down]67
[Filter counter]-67
[Test pattern][Off]68
[Network]-68
[Remote control][ALL]69
[Factory default]-70
[Memory Viewer]  
Sub-menu itemFactory defaultPage
[Set Slide]-71
[Slide Transition Effect][Slide Right]71
[Sort Order][Name Order]71
[Rotate][No Rotate]71
[Best Fit][Off]72
[Repeat][Off]72
[Apply]-72
[Info.]  
Details (x page 73)
Note
 fSome items may not be adjusted or used for certain signal formats to be \
input to the projector.  
The menu items that cannot be adjusted or used are shown in gray charact\
ers, and they cannot be selected.
 fSub-menu items and factory default settings differ depending on the selected input terminal.
Chapter 4   Settings - Menu Navigation  
						

							48 - ENGLISH
Input menu
To select the input source directly by pressing the input selection butto\
ns on the remote control or to select the 
input source in the Input screen by pressing the  button on the control panel.
Switching the input source
When using the remote control
1) Press the input selection (, , , ,\
 ) buttons. 
 fThe selected input signal will be projected.
Press this button to switch to Computer 1/Component input.
Switch to Computer 2 input.
Switch to HDMI input.
Press this button to switch to Video/S-video input.

Press this button to switch to Memory Viewer/USB Display/Network input.
When using the control panel
1) Press the  button.
 fThe Input screen is displayed.
2) Press as to select one item and then press the  button.
 fThe selected input signal will be projected.
Note
 fThe still-image transmission application software “Presenter Light” (x page 83) or “VueMagic” (x page 84) is necessary while projecting [Network] input. 
Chapter 4   Settings - Input menu  
						

							ENGLISH - 49
[Display] menu
On the menu screen, select [Display] from the main menu, and select an i\
tem from the sub-menu.Refer to “Navigating through the menu” (x page 44) for the operation of the menu screen.
 fAfter selecting the item, press as to set.
[Auto PC adj.]
(Only for computer signals input)
When input the computer (RGB) signals, the image may be moved up, down, left or right such as flickering, press the  button to adjust [Fine sync], [H position], [V position] and [H.Size] automatically in optimal state. Set the image to get 
an optimal state to match with the audio-visual surroundings in which th\
e projector is used.
1) Press as to select [Auto PC adj.]. 
2) Press the  button.
 f[Please wait] screen is displayed, the Auto PC adj. function will be executed.
Note
 fThe projector executes the Auto PC adj. automatically when the computer signals input the projector for the first time.
 fAutomatic adjustment may not work depending on the model of the computer\
 and the input signal.
 fThe [Auto PC adj.] cannot be operated when [480i], [576i], [480p], [576p], [720p], [1080i] or [1080p] is selected in the 
[Display] menu → [System], or when the signal is coming from the  terminal.
[Fine sync]
(Only for computer signals input)
You can adjust to achieve an optimal image when there is a flickering image or smeared outlines.
1) Press as to select [Fine sync].
2) Press the  button.
3) Press as to adjust the level.
 fThe adjustment values are 0 to +31. Adjust so that the amount of interference is at a minimum.
Note
 fCertain signals may not be adjustable.
 fOptimal value may not be achieved if the output from the input computer is unstable.
 fTo project a signal with dot clock frequency with 162 MHz or higher, noise may not disappear even if [Fine sync] is adjusted.
 f[Fine sync] cannot be adjusted when a digital signal is input.
[H Position]
(Only for computer signals input)
Move the image position horizontally if the image position projected on the screen is shifted even when the relative position of 
the projector and the screen is installed correctly.
1) Press as to select [H Position].
2) Press the  button.
3) Press as to adjust the horizontal image position.
Chapter 4   Settings - [Display] menu  
						

							50 - ENGLISH
OrientationOperationAdjustment
Horizontal (left and 
right) adjustment.
Press the a button.The image position moves to the right.
Press the s button.The image position moves to the left.
Note
 f[H Position] is not available while the image is expanded in the digital zoom function.
[V Position]
(Only for computer signals input)
Move the image position vertically if the image position projected on th\
e screen is shifted even when the relative position of the projector and the screen is installed correctly.
1) Press as to select [V Position].
2) Press the  button.
3) Press as to adjust the vertical image position.
OrientationOperationAdjustment
Vertical (up and down) 
adjustment.
Press the a button.The image position moves up.
Press the s button.The image position moves down.
Note
 f[V Position] is not available while the image is expanded in the digital zoom function.
[H.Size]
(Only for computer signals input)
Use this function to adjust and minimize the effect of interference caused by projection of patterns consisting of vertical stripes.
The projection of the vertical striped pattern may cause cyclic patterns (noise). Adjust so that the amount of interference is at a minimum.
1) Press as to select [H.Size].
2) Press the  button.
3) Press as to adjust the level.
 fThe adjustment values are -15 to +15.
Attention
 fSet it before adjusting [Fine sync].
[Aspect]
Provide the image to fit the screen size while maintaining the aspect ratio of the input signal.
1) Press as to select [Aspect]. 
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[Normal]Projects the image at the maximum size while maintaining the aspect ratio of the input signal.
[Wide]Projects the image at 16:9 aspect ratio.
Note
 fWhen the Memory Viewer, the USB Display or the Network input is selected, [Aspect] cannot be selected.
Chapter 4   Settings - [Display] menu