Panasonic LCD Projector Pt Tw341 Operating Instructions

							ENGLISH - 51
[Color adjust] menu
On the menu screen, select [Color adjust] from the main menu, and select\
 an item from the submenu.Refer to “Navigating through the menu” (x page 43) for the operation of the menu screen.
 fAfter selecting the item, press as to set.
[Image mode]
You can switch to the desired picture mode suitable for the image source and the environment in which the projector is used.
1) Press as to select [Image mode]. 
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[Dynamic]The light output is maximized for use in bright areas.
[Standard]The picture becomes suitable for moving images in general.
[Cinema]The picture becomes suitable for movie sources.
[Blackboard 
(Green)]The picture becomes suitable for projecting on a black board (green board) such as classroom.
[Colorboard]
The picture becomes suitable for projecting on a color board. To select [Colorboard], press the 
 button, the [Colorboard] screen is displayed. To select [Red], [Blue], [Yellow] or [Green], 
and press the  button.
[User image]The picture quality is displayed after the manual adjustment of [Color adjust].
4) Press the  button.
[Contrast]
You can adjust the contrast of the colors.
1) Press as to select [Contrast].
2) Press the  button.
3) Press as to adjust the level.
OperationAdjustmentAdjustment range
Press the a button.Brightens the screen and makes the color deeper.0 ~ +63Press the s button.Darkens the screen and makes the color lighter.
Attention
 fAdjust [Brightness] first when you need to adjust [Brightness] and [Contrast].
[Brightness]
You can adjust the dark (black) part of the projected image.
1) Press as to select [Brightness].
2) Press the  button.
3) Press as to adjust the level.
Chapter 4   Settings - [Color adjust] menu  
						

							52 - ENGLISH
OperationAdjustmentAdjustment range
Press the a button.Increases the brightness of the dark (black) parts of the screen.0 ~ +63Press the s button.Reduces the brightness of the dark (black) parts of the screen.
[Color]
(Except for computer signal input) 
You can adjust the color saturation of the projected image.
1) Press as to select [Color].
2) Press the  button.
3) Press as to adjust the level.
OperationAdjustmentAdjustment range
Press the a button.Deepens colors.0 ~ +63Press the s button.Weakens colors.
[Tint]
(Only for HDMI signals/Component signals and NTSC/NTSC4.43 signals when input Video or S-video signals)
You can adjust the skin tone in the projected image.
1) Press as to select [Tint].
2) Press the  button.
3) Press as to adjust the level.
OperationAdjustmentAdjustment range
Press the a button.Adjusts skin tone toward greenish color.0 ~ +63Press the s button.Adjusts skin tone toward reddish purple.
[Color temp.]
You can switch the color temperature if the white areas of the projected image are bluish or reddish.
1) Press as to select [Color temp.].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[High]Becomes a bluish image at [High]. Becomes a reddish image at [Low]. Sele\
cts the suitable natural 
color.[Mid]
[Low]
Note
 fWhen computer signal input, if the [Display] menu → [System] is set to [PAL], [SECAM], [PAL-M], [PAL-N], [NTSC], 
[NTSC4.43], [1080i], [1080p], [720p], [576p], [576i], [480p] or [480i], [Color temp.] will be unavailable.
[Red] / [Green] / [Blue]
You can adjust the white balance.
1) Press as to select [Red] / [Green] / [Blue].
2) Press the  button.
3) Press as to adjust the level.  
MenuOperationAdjustmentAdjustment range
[Red]Press the a button.Deepen red tone.0 ~ +63Press the s button.Lighten red tone.
Chapter 4   Settings - [Color adjust] menu  
						

							ENGLISH - 53
[Green]Press the a button.Deepen green tone.0 ~ +63Press the s button.Lighten green tone.
[Blue]Press the a button.Deepen blue tone.0 ~ +63Press the s button.Lighten blue tone.
[Sharpness]
You can adjust the sharpness of the projected image.
1) Press as to select [Sharpness].
2) Press the  button.
3) Press as to adjust the level.
OperationAdjustmentAdjustment range
Press the a button.Contours become sharper.0 ~ +15Press the s button.Contours become softer.
[Daylight View]
The Daylight View Lite function improves the vividness of the image even if it is proj\
ected under a bright light.
1) Press as to select [Daylight View].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
 fYou can also press the  button on the remote control. (x page 41)
[On]Enables Daylight View Lite function.
[Off]Disables Daylight View Lite function.
Chapter 4   Settings - [Color adjust] menu  
						

							54 - ENGLISH
[Setting] menu
On the menu screen, select [Setting] from the main menu, and select an i\
tem from the submenu.Refer to “Navigating through the menu” (x page 43) for the operation of the menu screen.
 fAfter selecting the item, press asqw to set.MEMORY VIEWER/
USB DISPLAY
ASPECTINFO.
IMAGE LAMP
DAYLIGHT VIEW
COMPUTER 1 COMPUTER 2
VIDEO
ENTER
MENU
KEYSTONE
FREEZE AV MUTE P-TIMER
D.ZOOMVOLUME
MUTE
[On start]
Set the method of start up when the power cord plugged into the  AC outlet.
1) Press as to select [On start].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[Off]Starts up in the standby mode.
[On]Starts the projection immediately.
Note
 fWhen you do not turn off the projector in procedure of “Powering Off the Projector” (x page 35), the On start function will 
not work properly.
[Standby mode]
Set the power consumption during standby. Change the setting whether or not use the network function.
1) Press as to select [Standby mode].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[Eco]Restricts some functions in the standby mode to reduce power consumption\
.
[Normal]Does not restrict network function and serial communication function eve\
n in the standby mode.
Note
 fIf [Standby mode] is set to [Eco], you cannot use network functions and some RS-232C commands.
[High land]
Change the setting according to the altitude in which you use the projector .
1) Press as to select [High land].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[Off]When using the projector in the elevation of below 1 400 m (4 593').
[On]When using the projector in the elevation of above 1 400 m (4 593') and below 2 700 m (8 858').
Chapter 4   Settings - [Setting] menu  
						

							ENGLISH - 55
Note
 fIt is set to [Off] when using the projector in the elevation of below 1 400 m (4 593’). It is set to [On] when using the projector in the elevation of above 1 400 m (4 593’) and below 2 700 m (8 858’). Failure to do so may shorten the life of the internal parts and result in malfunctions. fDo not set the projector in the elevation of 2 700 m (8 858’) or above, otherwise it may shorten the life of the internal parts and result in malfunctions.
 fWhen it is set to [On], the fan noise becomes louder and fan speed increases. 
[Lamp control]
Switch the brightness of the lamp according to the operating environment\
 of the projector or the purpose.
1) Press as to select [Lamp control].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
 fYou can also press the  button on the remote control. (x page 39)
[  (Normal)]Select when high luminance is required.
[  (Eco 1)]Select when high luminance is not required.
[  (Eco 2)]Select when lower luminance than [  (Eco 1)] is required.
Note
 fSet it to [  (Eco 2)] rather than [  (Eco 1)], set it to [  (Eco 1)] rather than [  (Normal)], when you want to reduce 
power consumption, extend the life of lamp and reduce operation noise.
[Cooling fast]
Switch the cooling fan' speed when the power is turned off and shorten the cooling time of the cooling fan.
1) Press as to select [Cooling fast].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[Normal]Use this setting normally.
[60 Sec]Use this setting when short cooling period of time is required.
[0 Sec]The cooling fans stop immediately after power-off.
Note
 fWhen it is set to [0 sec], you cannot restart the projector immediately \
after the power-off. The lamp remains high temperature 
and needs to be cooled, so it sometimes takes longer time than usual for\
 the lamp to light up again. 
 fWhen it is set to [60 sec], the cooling fans’ speed is faster and the motor noise is louder than [Normal] setting after the 
power-off.
[Closed caption]
(Only for NTSC input)
Set the closed caption.
1) Press as to select [Closed caption].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[Off]Closed caption is not displayed.
[CC1]Displays CC1 data.
[CC2]Displays CC2 data.
[CC3]Displays CC3 data.
[CC4]Displays CC4 data.
Note
 fClosed caption is a function that displays text information of video signals mainly used in North America. Captions may not 
be displayed depending on the connected devices or contents being played\
 back.
Chapter 4   Settings - [Setting] menu  
						

							56 - ENGLISH
 f[Closed caption] can only be selected if an NTSC signal is input.
 fIf [Closed caption] is set to the item except for [Off], the brightness of image may be changed according to the external 
devices or the used content of the closed caption corresponding connecti\
on.
 fClosed captions are not displayed when the menu screen is displayed.
[Key lock]
Enable/disable the button operations on the control panel and the remote\
 control.
1) Press as to select [Key lock].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[  (Off)]Enables the button operations on the control panel or the remote control\
.
[  (Projector)]Disables the button operations on the control panel.
[  (Remote control)]Disables the button operations on the remote control.
[Iris]
Aperture correction and signal compensation are performed automatically \
based on the image to result in an image of 
optimum contrast.
1) Press as to select [Iris].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[On]Corrects the aperture.
[Off]No aperture correction.
[Terminal]
The  terminal on the back of the projector is switchable for computer 2 input or monitor output.
1) Press as to select [Terminal].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[Monitor out]Outputs the RGB signal which have been input  terminal.
[Computer 2]When input the computer signal.
Note
 fThe [Terminal] will be unavailable when [Computer 2] is selected as input source.
[Sound]
You can perform more detailed setting for Audio.
Adjusting the volume
1) Press as to select [Sound].
2) Press the  button.
 fThe [Sound] screen is displayed.
3) Press as to select [Volume].
4) Press the  button.
5) Press as to adjust the level.
Chapter 4   Settings - [Setting] menu  
						

							ENGLISH - 57
 fYou can also press the  button on the remote control. (x page 40)
OperationAdjustmentRange
Press the a button.Turns up the volume.0 ~ +25Press the s button.Turns down the volume.
Setting the mute
1) Press as to select [Sound].
2) Press the  button.
 fThe [Sound] screen is displayed.
3) Press as to select [Mute].
4) Press the  button.
5) Press as to switch the item.
 fThe items will switch each time you press the button.
 fYou can also press the  button on the remote control. (x page 40)
[On]Audio is not output.
[Off]Audio is output.
[HDMI Setup]
Switch the setting when the external equipment is connected to the  terminal of the projector and the image is not 
projected correctly. Or switch the setting of the audio input.
[Image]
1) Press as to select [HDMI Setup].
2) Press the  button.
 fThe [HDMI Setup] screen is displayed.
3) Press as to select [Image].
4) Press the  button.
5) Press as to switch the item.
 fThe items will switch each time you press the button.
[64-940]Select when the HDMI terminal of an external device (such as a blu-ray player) is connected to the 
 terminal.
[0-1023]
Select when the DVI-D terminal output of an external device (such as a computer) is connected 
to the  terminal via a conversion cable or similar cable. Selec\
t also when the HDMI 
terminal output of a computer or other device is connected to the  terminal.
Note
 fThe optimal setting varies depending on the output setting of the connected external device. Refer to the operation 
instruction of the external device regarding the output of the external device.
[Sound]
1) Press as to select [HDMI setup].
2) Press the  button.
 fThe [HDMI setup] screen is displayed.
3) Press as to select [Sound].
4) Press the  button.
5) Press as to switch the item.
 fThe items will switch each time you press the button.
[HDMI]Select when the HDMI cable is connected, the image and audio are transmi\
tted, and you do not 
need to connect the audio signal separately.
[Computer]
Select when the DVI-D terminal output of an external device (such as a computer) is connected to 
the  terminal via a conversion cable or similar cable. The image will not be transmitted, 
the audio signal is input to  terminal.
Chapter 4   Settings - [Setting] menu  
						

							58 - ENGLISH
[Expand] menu
On the menu screen, select [Expand] from the main menu, and select an it\
em from the submenu.Refer to “Navigating through the menu” (x page 43) for the operation of the menu screen.
 fAfter selecting the item, press asqw to set.
[Language]
You can switch the language of the on-screen display.
1) Press as to select [Language].
2) Press the  button.
 fThe [Language] screen is displayed. (It is displayed in 23 languages with 3 pages.)
3) Press as to switch the language.
 fThe languages will switch each time you press the button.
4) Press the  button.
 fVarious menus, settings, adjustment screens, control button names, etc., \
are displayed in the selected language.
 fThe language can be changed to English, German, French, Italian, Spanish, Portuguese, Dutch, Swedish, Finnish, 
Norwegian, Danish, Polish, Hungarian, Czech, Russian, Turkish, Arabic, Kazakh, Vietnamese, Chinese, Korean, 
Japanese and Thai.
Note
 fThe on-screen display language of the projector is set to English by default and when [Expand] → [Factory default] is 
executed (x page 69).
[Auto setup]
Press the  button on the remote control to set the automatic operations of the Input search function, Auto PC 
adj. function and the Auto keystone function.
1) Press as to select [Auto setup].
2) Press the  button.
 fThe [Auto setup] screen is displayed.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
Chapter 4   Settings - [Expand] menu  
						

							ENGLISH - 59
[Input search]This function is used to detect the signals and project the automatic in\
put signals automatically.
[Auto PC adj.]This function is used to adjust [Fine sync], [H position], [V position] and [H.Size] automatically 
when input the analog computer signal.
[Auto keystone]This function is used to correct the vertical keystone of the projected \
image automatically.
[Input search]
This function is used to detect the signals and project the automatic in\
put signals automatically.
1) Press as to select [Auto setup].
2) Press the  button.
 fThe [Auto setup] screen is displayed.
3) Press as to select [Input search].
4) Press the  button.
5) Press as to switch the item.
 fThe items will switch each time you press the button.
[On]Detects the signals and projects the automatic input signals automatical\
ly.
[Off]Disables the detection of the signals.
[Auto PC adj.]
This function is used to set the automatic execution of Auto PC adj. function.
1) Press as to select [Auto setup].
2) Press the  button.
 fThe [Auto setup] screen is displayed.
3) Press as to select [Auto PC adj.].
4) Press the  button.
5) Press as to switch the item.
 fThe items will switch each time you press the button.
[On]Enables the automatic execution of Auto PC adj. function.
[Off]Disables the automatic execution of Auto PC adj. function.
[Auto keystone]
This function is used to set the automatic execution of Auto keystone function.
1) Press as to select [Auto setup].
2) Press the  button.
 fThe [Auto setup] screen is displayed.
3) Press as to select [Auto keystone].
4) Press the  button.
5) Press as to switch the item.
 fThe items will switch each time you press the button.
[Auto]When detecting the projector is tilted, correct the vertical keystone in\
 real time. 
[Manual]When pressing the  button on the remote control, correct the keystone in vertical.
[Off]Auto keystone function disabled.
Note
 f[Input search], [Auto PC adj.] and [Auto Keystone] cannot be set to [Off] at the same time. At least one of them is set to [On].
 fIn some times the auto keystone maybe correct image imperfectly, manual keystone is required.
 fWhen [Display] → [Project way] is set to [Ceiling/Front] or [Ceiling/Rear], [Auto PC adj.] will be set to [On] automatically , 
[Auto keystone] will be set to [Off] automatically and it will be unavailable.
Chapter 4   Settings - [Expand] menu  
						

							60 - ENGLISH
[Keystone]
You can correct the trapezoidal distortion that occurs when the projector is installed tilted or when the screen is tilted.
1) Press as to select [Keystone].
2) Press the  button.
 fThe [Keystone] screen is displayed.
3) Press as to select one item.
[Keystone]Sets whether or not to keep the keystone correction after turn off the projector or plug out 
the power cord.
[H/V Keystone]Adjusts when the horizontal or vertical trapezoid of the projected image is distorted.
[Corner correction]Adjusts when the four corners of the projected image are distorted.
[Curved correction]Adjusts when the linearity is not uniform or the vertical and horizontal lines are distorted.
[Reset value]Return the corrected values to the factory default values.
[Keystone]
Sets whether or not to keep the keystone correction after turn off the projector or plug out the power cord.
1) Press as to select [Keystone].
2) Press the  button.
 fThe [Keystone] screen is displayed.
3) Press as to select [Keystone].
4) Press the  button.
5) Press as to switch the item.
 fThe items will switch each time you press the button.
[Reset]
When [Standby mode] is set to [Eco], plug out the power cord or turn off the projector, the 
keystone correction will be canceled. When [Standby mode] is set to [Nor\
mal], plug out the power 
cord, the keystone correction will be canceled; turn off the projector, the keystone correction will 
be kept.
[Store]The keystone correction will be kept when plug out the power cord or tur\
n off the projector.
[H/V Keystone]
1) Press as to select [Keystone].
2) Press the  button.
 fThe [Keystone] screen is displayed.
3) Press as to select [H/V Keystone].
4) Press the  button.
 fThe [H/V Keystone] individual adjustment screen is displayed.
5) Press asqw to adjust the item.
ItemsOperationAdjustment
Horizontal
Press the w button.Adjusts the right of the keystone.
Press the q button.Adjusts the left of the keystone.
Chapter 4   Settings - [Expand] menu