Panasonic LCD Projector Pt Tw340 Operating Instructions

							ENGLISH - 71
[Memory Viewer] menu
On the menu screen, select [Memory Viewer] from the main menu, and select an item from the sub-menu.Refer to “Navigating through the menu” (x page 44) for the operation of the menu screen.
 fAfter selecting the item, press as to set.
Note
 fMemory Viewer function is only for PT-TW340, PT-TW250, PT-TX400 and PT-TX310.
 fThe [Memory Viewer] menu is available when input the [Memory Viewer] signal.
 fThe menu except for [Set Slide] which settings have been changed is not yet effective before the [Apply] is not executed.
[Set Slide]
Start the slide show.
1) Press as to select [Set Slide].
2) Press the  button.
 fSlide show will start.
[Slide Transition Effect]
Set the slide transition effect when the slide show image is switching.
1) Press as to select [Slide Transition Effect].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[Slide down]Switches the image from the top to the bottom.
[Slide right]Switches the image from the left to the right.
[Sort Order]
Set the sort order of the slide show.
1) Press as to select [Sort Order].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[Extend order]Sort files or folders in extended order.
[Size order]Sort files or folders in amount of data order.
[Time order]Sort files or folders in stored time order.
[Name order]Sort files or folders in name order.
[Rotate]
Set the rotate direction of image.
1) Press as to select [Rotate].
2) Press the  button.
3) Press as to switch the item.
Chapter 4   Settings - [Memory Viewer] menu  
						

							72 - ENGLISH
 fThe items will switch each time you press the button.
[No rotate]Rotate is disabled.
[270 Degrees]Rotates 270 degrees in anti-clockwise direction.
[180 Degrees]Rotates 180 degrees.
[90 Degrees]Rotates 90 degrees in anti-clockwise direction.
[Best Fit]
Set the image whether or not to fit with the projected screen.
1) Press as to select [Best Fit].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[On]Displays the image to fit with the aspect of the projected screen.
[Off]Displays in the normal pixels of the image.
[Repeat]
Set whether or not to play the slide show repeatedly.
1) Press as to select [Repeat].
2) Press the  button.
3) Press as to switch the item.
 fThe items will switch each time you press the button.
[On]Repeat broadcast the first file after the last file is broadcasted.
[Off]Return to the thumbnail display after the last file is broadcasted.
[Apply]
Executes the setting in slide show.
1) Press as to select [Apply].
2) Press the  button.
 fThe setting of the items except for [Set Slide] will be effective.
Chapter 4   Settings - [Memory Viewer] menu  
						

							ENGLISH - 73
[Info.] menu 
On the menu screen, select [Info.] from the main menu.
Refer to “Navigating through the menu” (x page 44) for the operation of the menu screen.
[Info.]
Display the status of the projector.
1) Press as to select [Info.].
 fThe [Info.] screen is displayed.
 fYou can also press the  button on the remote control. (x page 40)
[Input]The selected input source and the system are displayed.
[H-sync freq.]The horizontal frequency of the input signal is displayed in kHz. [- - - - ] is displayed when no 
signal is detected.
[V-sync freq.]The vertical frequency of the input signal is displayed in Hz. [- - - -] is displayed when no signal 
is detected.
[Lamp status]The setting status of [Lamp control] is displayed.
[Lamp counter]The usage time of the lamp is displayed. (Displays the converted runtime when [  (Eco 1)] is 
using.)
[Power management]The setting status of [Power management] is displayed.
[Image mode]The setting status of [Image mode] is displayed.
[S/N]The serial number of the projector is displayed. The serial number is used to service the 
projector.
Chapter 4   Settings - [Info.] menu   
						

							74 - ENGLISH
Network control
Network connections
The projector has a network function, and the following operations are available from the computer using the web browser control.
 fSetting and adjustment of the projector. fDisplay of the projector status.
Note
 fA LAN cable is required to use the network function.
 rExample of a normal network connection
AC IN 
 fA Web browser is required to use this function. Confirm that the Web browser can be used beforehand. 
Compatible Web Browser : Internet Explorer 7.0/8.0/9.0/10.0, Safari 4.0/5.0/6.0 (Mac OS)
 fUse shielded LAN cable (STP cable) that is compatible with category 5 or above.
 fUse a LAN cable with length of 100 m or shorter.
 rName and function of network function parts123
1 LAN LINK/ACT lamp (yellow) Lights on when connected. Blinks when transmitting/receiving data.
2  terminal (10BASE-T/100BASE-TX)Used to connect LAN cable here.
3 LAN 10/100 lamp (green)Lights on when connected to the 100BASE-TX.
Attention
 fWhen a LAN cable is directly connected to the projector, the network connection must be made indoors.
 f 
When connecting cables to both the  terminal and the  terminal, it may be difficult to remove 
the LAN cable which is connected to the  terminal. When removing th\
e LAN cable from the  terminal, remove a 
cable connected to the  terminal or the  terminal beforehand.
Projector settings
1) Use the LAN cable (Straight) to connect the projector with computer.
2) Turn on the projector.
3) Set the [Expand] menu → [Network] → [Network setting] 
 fFor details, refer to the [Expand] menu → [Network] (x page 69).
ComputerProjector
LAN cable (straight)LAN cable (straight)
Hub
Chapter 4   Settings - Network control  
						

							ENGLISH - 75
Note
 fPlease confirm with your network administrator before you connect to an existing network.
 fThe following settings are set before the projector leaves the factory.
[DHCP]Off
[IP address]192.168.1.100
[Subnet]255.255.255.0
[Gateway]192.168.1.1
[DNS]192.168.1.1
Computer operation
Connection can be made with wired LAN. However, confirm to your system administrator on network settings before chang-ing any settings.
1) Turn on the computer.
2) Make the network setting according to your system administrator.
 fIf the projector settings are the default settings, the computer can be \
used with the following network settings.
[IP address]192.168.1.101
[Subnet]255.255.255.0
[Gateway]192.168.1.1
Accessing from the Web browser
1) Activate the Web browser in the personal computer.
2)  Enter the IP address set by the projector into the URL input field of the Web browser. 
 fThe [Network Display System] screen is displayed.
3) Click [Login] and enter the password in the [Password] column.
 fThe factory default setting of the user name is “admin” (administrator rights) and the password is “admin”.
4) Click [Login].
 fThe [System Status] page is displayed.
Note
 fYou can click the upper right corner of the web browser screen to select the display language.
 fDo not perform setting or control simultaneously by starting up multiple\
 web browsers. Do not set or control the projector 
from multiple computers.
 fChange the password first. (8 half-width characters) (x page 76)
 fIf the screen for the web control is not displayed, consult your network\
 administrator.
Chapter 4   Settings - Network control  
						

							76 - ENGLISH
Description of each item
12
3
4
5
1 [System Status]The [System Status] page is displayed by clicking this item.
2 [General Setup]The [General Setup] page is displayed by clicking this item.
3 [Picture Setup]The [Picture Setup] page is displayed by clicking this item.
4 [Image Setup]The [Image Setup] page is displayed by clicking this item.
5 [Network Setup]The [Network Setup] page is displayed by clicking this item.
[System status] page
Display the status of the projector for the following items.
1
2
3
1 [Model Name]Displays the model No. of the projector.
2 [Versions]Displays the version of the firmware of the projector.
3 [LAN Status]Displays the connection status of the LAN.
[General Setup] page
[Change Password for Webpage] is displayed.
1
2
3
4
5
6
1 [Enter Old password]Enters the configured password.
2 [Enter New password]Enters the new password.
3 [Confirm New password]Enters the desired new password again for confirmation.
4 [Apply]Updates the settings.
5 [Power]Turns on/off the power.
6 [Source Select]Switches the input source of the projector.
Chapter 4   Settings - Network control  
						

							ENGLISH - 77
[Picture Setup] page
1
2
3
4
5
6
1 [Brightness]Adjusts the brightness of the projected image.
2 [Contrast]Adjusts the contrast of the projected image.
3 [Sharpness]Adjusts the sharpness of the projected image.
4 [Color]Adjusts the color saturation of the projected image.
5 [Tint]Adjusts the skin tone of the projected image.
6 [Color temperature]Adjusts the color temperature of the projected image.
[Image Setup] page
1
2
3
4
8
9
10
11
5
6
7
Chapter 4   Settings - Network control  
						

							78 - ENGLISH
1 [Aspect]Switches the aspect of the projected image.
2 [Fine sync]Adjusts the fine sync of the projected image.
3 [H Position]Adjusts the horizontal position of the projected image.
4 [V Position]Adjusts the vertical position of the projected image.
5 [H.Size]
Adjusts the total number of dots of the projected 
image.
6 [Freeze]Switches the freeze function between on and off.
7 [Auto PC adj.]Executes the Auto PC adj. function.
8 [V Keystone]Corrects the keystone in vertical direction.
9 [H Keystone]Corrects the keystone in horizontal direction.
10 [Curved correction]Corrects the pincushion or barrel of the projected image.
11 [Corner correction]Corrects the four corners of the projected image.
[Network Setup] page
1
2
1 [LAN Setup]
Select [Obtain an IP address automatically] if you 
want to enable the DHCP client.[IP Address]Enter the IP address when not using a DHCP server.[Subnet]Enter the subnet mask when not using a DHCP server.[Gateway]Enter the default gateway address when not using a DHCP server.[DNS]Enter the DNS server when not using a DHCP server.Allowed characters: Numbers (0 - 9), period (.)(Example: 192.168.0.253)
2 [Apply]Updates the settings.
Chapter 4   Settings - Network control  
						

							ENGLISH - 79
Using useful functions
Memory Viewer function
The Memory Viewer function makes it is possible to project the video and pictures wh\
ich are stored in the USB memory when 
the USB memory is inserted into the projector.
 rWhat you can project with the Memory Viewer function
Memory Viewer function supports the following image files.
Video
ExtensionVideo codecAudio codecVideo format
aviMotionJpegADPCMYUV 4:4:4, YUV 4:2:2, YUV 4:2:0
Maximum: 1 280 x 720, 30 fps
Picture
ExtensionFormatDescription
jpg/jpegBaseline coding 24 bits
Progressive RGB 24 bits
Resolution : 8 x 8 ~ 10 000 x 10 000 Resolution : 8 x 8 ~ 1 280 x 800 
bmpPalette-based 1, 4, 8 bits,  
RGB 24, 32 bitsThe maximum resolution : 1 280 x 800 
pngTrue color 24 bits/48 bitsThe maximum resolution : 1 280 x 800 
gifPalette-based 1, 4, 8 bits, Palette - 24 bits color spaces;  
The maximum resolution : 1 280 x 800 
tif / tiffThe maximum resolution : 1 280 x 800 
pdf
Note
 fThe maximum size of file is 2 GB.
 fThe maximum number of file/folder is up to 500. If it exceeds the folder cannot display and an error message appears.
 fYou cannot play the files which is protected by Digital Rights Management (DRM).
 fYou cannot play the PDF files which are protected by security setting.
 fIt maybe impossible to resume playing even if the file is recorded in the supported format.
 rThe related device
It is compatible with the USB memory sold in the market. (Do not ensure the security.)
It cannot be used the other format other than the formatted with FAT16 and FAT32.
Displaying the Memory Viewer screen
1) Press the  button on the remote control or switch the input source 
to [Memory Viewer].
 fPress the  button on the control panel and select the input\
 source in the Input menu.
2) Insert the USB memory directly into the  terminal.
 fThe standby screen “please press RC ENTER ” is displayed while the USB memory icon is displayed at the lower left of 
the screen.
 fWhen the partition are separated in USB memory, several USB icons will be displayed.
3) Press the  button on the remote control.
 fThe root directory of the USB memory will be displayed in thumbnail on t\
he screen.
Playing the pictures
It will display a picture when play the picture manually every time.
1) Press asqw on the remote control to select a file.
2) Press the  button on the remote control.
 fThe picture will display on the full screen.
3) Press w to switch to the next picture, press q to return to the previous picture.
4) Press the  button on the remote control.
 fReturn to the thumbnail screen.
Executing the slide
All pictures in the same folder will play automatically when [Sort Order] and [Slide  Transition Effect] and so on of [Memory 
Viewer] menu are set to the special setting.
Chapter 4   Settings - Using useful functions  
						

							80 - ENGLISH
1) Press asqw on the remote control to select a file.
2) Press the  button to select the [Memory Viewer] → [Set Slide].
3) Press the  button on the remote control.
 fThe picture will display on the full screen.
 fPress the  button to return to the thumbnail screen.
Note
 fIf you press the  button during the slide show, the image will stop and the a menu displays. The playing will continue when the menu disappears.
Playing the video
Playing the video file.
1) Press asqw on the remote control to select a file.
2) Press the  button on the remote control.
 fPlaying on the full screen.
 fTo operate the controller which is displayed on the bottom of the screen \
with the remote control.
Video playing is terminated, and return to the thumbnail screen.
 /  Pauses / plays the video.
10 seconds backward / forward skip and will continue to play thereafter.
60 seconds backward / forward skip and will continue to play thereafter.
 / The frame will switch between display and non-display each time you pres\
s the icon. The 
video can be played repeatedly when the frame is displayed.
Note
 fIf there are any invalid operations during video playing, the icon  indicating invalid key operations will appear.
Displaying the PDF 
Operating the controller to display the PDF.
1) Press asqw on the remote control to select a PDF file.
2) Press the  button on the remote control.
 fDisplaying the PDF on the full screen.
 fTo operate the controller which is displayed on the bottom of the screen \
with the remote control. fWhen the button is selected, the background display will be switched bet\
ween blue and white.
55GO1 1/10
/Displays the previous or next page.
/The page number ## of [55GO1 1/10##] increases or decreases by 1 page each time you click the 
button.
/The page number ## of [55GO1 1/10 ##] increases or decreases by 5 pages each time you click the 
button.
[ ##]Jumps to page number ## directly.
Switches between PDF full width display and single whole page display .
Switches the display size in 3 levels of magnification each time you click the button.
When the button is selected, press asqw on the remote control to move the display screen up, down, left and right. Clicks this button again to release it.
Terminates the PDF display and returns to the thumbnail display.
Note
 fPDF display is switched at intervals. Please do not perform continuous operations during a short period of time.
Chapter 4   Settings - Using useful functions