Panasonic LCD Projector Pt Tw230 Operating Instructions

							ENGLISH - 41
Settings
Select [Image adjust] from the Main Menu (see 
“Navigating through the menu” on page 32), 
then select the item from the sub-menu.
Remote controlControl panel
Contrast
Press ▲▼ to select [Contrast].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the setting value.3 ) 
OperationAdjustmentAdjustment 
range
Press ►.increase the contrastMaximum 
value 63
Press ◄.decrease the 
contrast
Minimum 
value 0
Brightness
Press ▲▼ to select [Brightness].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the setting value.3 ) 
OperationAdjustmentAdjustment 
range
Press ►.increase the 
brightness
Maximum 
value 63
Press ◄.decrease the 
brightness
Minimum 
value 0
Color
Press ▲▼ to select [Color].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the setting value.3 ) 
OperationAdjustmentAdjustment 
range
Press ►.increase the 
intensity of the color
Maximum 
value 63
Press ◄.decrease the 
intensity of the color
Minimum 
value 0
Note
When input video signal to the projector, [Color] will be  z
available.
Tint 
Press ▲▼ to select [Tint].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the tint value to 3 ) 
get a proper color balance.
Adjustments can be made between z 0 and 63.
Note
When you select [NTSC] or [NTSC4.43] in System menu  z
under Video input signal, [Tint] will be available.
Color temp.
Press ▲▼ to select [Color temp.].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to select the desired Color 3 ) 
temp. level.
You can select the desired [Color temp.] from  z
[XLow], [Low], [Mid] or [High].
Note
[Color temp.] level displays [Blackbord] or [Colorboard]  z
when the [Blackboard(Green)] or [Colorboard] is selected 
in the [Image select] menu.
Image adjust 
						

							Image adjust
42 - ENGLISH
Settings
Red 
Press ▲▼ to select [Red].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the setting value.3 ) 
OperationAdjustmentAdjustment 
range
Press ►.deepen red toneMaximum 
value 63
Press ◄.lighten red toneMinimum 
value 0
Green
Press ▲▼ to select [Green].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the setting value.3 ) 
OperationAdjustmentAdjustment 
range
Press ►.deepen green 
tone
Maximum 
value 63
Press ◄.lighten green 
tone
Minimum 
value 0
Blue 
Press ▲▼ to select [Blue].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the setting value.3 ) 
OperationAdjustmentAdjustment 
range
Press ►.deepen blue toneMaximum 
value 63
Press ◄.lighten blue toneMinimum 
value 0
Sharpness
Press ▲▼ to select [Sharpness].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the setting value.3 ) 
OperationAdjustmentAdjustment 
range
Press ►.
increase the 
sharpness of the 
image
Maximum 
value 15
Press ◄.
decrease the 
sharpness of the 
image
Minimum 
value 0
Gamma
Press ▲▼ to select [Gamma].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the gamma value 3 ) 
to obtain a better balance of contrast.
Adjustments can be made between z 0 and 15.
Noise reduction
Press ▲▼ to select [Noise reduction].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to select the desired item.3 ) 
OffDisabled
L 1Lower reduction
L 2Higher reduction
Noise interference on the screen can be  z
reduced. Select one of the above options to get 
smoother images.
[Noise reduction] cannot be selected when  z
[480p], [576p], [720p], [1035i], [1080i] or [1080p] 
is selected.
Note
When input video signal to the projector, [Noise  z
reduction] will become available. 
						

							Image adjust
ENGLISH - 43
Settings
Progressive
Press ▲▼ to select [Progressive].1 ) 
Press the  button to display 2 ) 
the dialog box.
Press ◄► to select the desired item.3 ) 
An interlaced video signal can be displayed in  z
progressive mode. Select one of the following 
options.
[Progressive] cannot be selected when [480p],  z
[576p], [720p], [1035i], [1080i] or [1080p] is 
selected.
OffDisabled
L 1For an active picture
L 2For a still picture
FilmFor watching a film
Note
When input video signal to the projector, [Progressive]  z
will become available.
Reset
To reset the adjusted data, all adjustments will return 
to their previous figures.
Press ▲▼ to select [Reset].1 ) 
Press the  button.2 ) 
A confirmation box appears and then select [Yes]. z 
Store
Press ▲▼ to select [Store].1 ) 
Press ► or the  button.2 ) 
Press ▲▼ to select one from Image 1 3 ) 
to 4 and press the  button.
A confirmation box appears and then select [Yes]. z  
						

							44 - ENGLISH
Settings
Screen 
Select [Screen] from the Main Menu (see 
“Navigating through the menu” on page 32), 
then select the item from the sub-menu.
Remote controlControl panel
Normal
Provide the image to fit the screen size while 
maintaining the aspect ratio of the input signal.
Press ▲▼ to select [Normal] and then 
press the  button.
Full 
Provide the full screen image.
Press ▲▼ to select [Full] and then press 
the  button.
Wide(16:9)
Provide the image at the 16:9 wide screen ratio.
Press ▲▼ to select [Wide(16:9)] and then 
press the  button.
Zoom
Scale the image proportionally to fit the entire screen. 
Either side of image may go over the screen.
Press ▲▼ to select [Zoom] and then 
press the  button.
True 
Provide the image in its original size. When the 
original image size is larger than the panel size (1280 
x 800), the projector enters to the panning mode 
automatically.
Press ▲▼ to select [True] and then 1 ) 
press the  button.
Press ▲▼◄► to pan the image.2 ) 
When adjusted, the arrows will turn red. When  z
reached to the correction limits, the arrows will 
disappear.
Note
When input computer signal to the projector, [True] will  z
be available.
[True] is disabled and cannot be displayed when [480i],  z
[576i], [480p], [576p], [720p], [1035i] or [1080i] is selected 
in the PC System Menu.
When [True] is selected in the Screen menu, [Digital  z
zoom +/-] can not be selected.
Natural wide 
Modify the 4:3 aspect ratio image to fit the screen size  
by stretching the image to make it look natural.
Press ▲▼ to select [Natural wide] and 
then press the  button. 
Note
When input video signal to the projector, [Natural wide]  z
will be available.
Custom
Provide the last stored aspect screen image.
Press ▲▼ to select [Custom] and press 
the  button.  
						

							ENGLISH - 45
Settings
Custom adj.
Adjust the screen scale and position manually with 
this function.
Press ▲▼ to select [Custom adj.].1 ) 
Press ► or the  button to 2 ) 
enter the next submenu.
Press ▲▼ to choose the item you 3 ) 
want to adjust.
You can choose one from the items as below: z
Scale H/VAdjust the Horizontal/Vertical screen 
scale.
H&VWhen set to [On], the aspect ratio is 
fixed.
Position H/VAdjust the Horizontal/Vertical screen 
position.
CommonSave the adjusted scale or position 
to all the inputs.
ResetReset the all adjusted values.
Digital zoom +
Zoom in the images.
Press ▲▼ to select [Digital zoom +] 1 ) 
and then press the  button.
The On-Screen Menu disappears and                                 z
[D. zoom + ] appears.
Press the  button to zoom in 2 ) 
the image size and press ▲▼ ◄► to 
move the image to the top/bottom/left/
right of the screen.
The Panning function can work only when the  z
image is larger than the screen size. A projected 
image can be also expanded by pressing the 
 or the  button.
Digital zoom -
Zoom out the images.
Press ▲▼ to select [Digital zoom -] 1 ) 
and then press the  button.
The On-Screen Menu disappears and                                                                                                                                               z
[D. zoom - ] appears.
Press the  button to zoom 2 ) 
out image size.
The projected image can be also compressed  z
by pressing the  or the  
button.
To exit the Digital zoom +/– mode, press any button 
except the ,  and ▲▼◄► 
buttons.
To return to the previous screen size, select a screen 
size from the Screen Size Adjustment Menu or select 
an input source from the Input Source Selection Menu 
(Æpage 37) again, or adjust the screen size with the 
 buttons.
Note
When input computer signal to the projector,   z
[Digital zoom +/-] will be available.
[Digital zoom +/-] cannot be selected when [True] is  z
selected in the Screen aspect.
[Digital zoom +/–] are disabled and cannot be displayed  z
when [480i], [576i], [480p], [576p], [720p], [1035i] or 
[1080i] is selected in the PC System Menu (Æpage 35).
When [Digital zoom +/–] functions are disabled,          z
mark will appear.
Keystone
This function is used to adjust keystone distortion of 
the projected image.
Press ▲▼ to select [Keystone].1 ) 
Press ► or the  button.2 ) 
Press ▲▼ to choose the item you 3 ) 
want to adjust.
KeystoneTo correct keystone distortion
StoreTo store or reset the keystone 
correction
Store
Keep the keystone correction 
even when the AC power cord is 
unplugged or turning off the projector. 
Reset
Release the keystone correction 
when the AC power cord is 
unplugged .
Screen 
The following items are the 
submenus of [Store]. 
						

							46 - ENGLISH
Settings
Ceiling
This function is used to project the image from a 
ceiling-mounted projector.
Press ▲▼ to select [Ceiling] and then 1 ) 
press the  button.
Press ▲▼ to change the image.2 ) 
When this function is set to [On], the picture will  z
be top/bottom and left/right reversed.
Rear
This function is used to project the image from rear of 
the screen.
Press ▲▼ to select [Rear] and then 1 ) 
press the  button.
Press ▲▼ to change the image.2 ) 
When this function is set to [On], the picture will  z
be left/right reversed.
Screen acpect
This function is used to project the image to a 4:3 or 
16:9 projection screen.
Press ▲▼ to select [Screen aspect] 1 ) 
and then press the  button.
Press ▲▼ to choose one from the 2 ) 
items as below.
Default(16:10)16:10 is the aspect of the LCD 
panel.
16:9Set to a 16:9 projection screen. 
4:3Set to a 4:3 projection screen.
Attention
When the [4:3] function is selected, [Natural wide] is not  z
available in the AV screen.
When the [16:9] function is selected, [Wide (16:9)] is not  z
available in the screen.
[Natural wide] will grayout when [720p], [1035i], [1080i] or  z
[1080p] is selected in the AV System Menu.
Reset
To reset the adjusted data, all adjustments will return 
to their previous figures.
Press ▲▼ to select [Reset] and then 
press the  button.
A confirmation box appears and then select  z
[Yes].
Screen  
						

							ENGLISH - 47
Settings
Sound
Select [Sound] from the Main Menu (see 
“Navigating through the menu” on page 32), 
then select the item from the sub-menu.
Remote controlControl panel
Volume
Press ▲▼ to select [Volume] and then 1 ) 
Press the  button.
Press ◄► to adjust the volume.2 ) 
OperationAdjustmentAdjustment 
range
Press ►.turn up the 
volume
Maximum 
value 63
Press ◄.turn down the 
volume
Minimum 
value 0
You can also press  buttons on  z
the remote control or control panel to adjust the 
volume.
Mute
Press ▲▼ to select [Mute] and then 1 ) 
Press the  button.
Press the  button to switch 2 ) 
the mute function On/Off.
Press the  button on the remote  z
control to temporarily turn off the sound. To turn 
the sound back on, press the  button 
again or press the  buttons. 
 
 
 
  
						

							48 - ENGLISH
Settings
Setting
Select [Setting] from the Main Menu (see 
“Navigating through the menu” on page 32), 
then select the item from the sub-menu.
Remote controlControl panel
Language
Press ▲▼ to select [Language].1 ) 
Press ► or the  button.2 ) 
Press ▲▼ to select the desired 3 ) 
language.
The language used in the On-Screen Menu is  z
available in English, German, French, Italian, 
Spanish, Portuguese, Dutch, Swedish, Finnish, 
Norwegian, Danish,  Polish, Hungarian, Romanian, 
Czech, Russian, Turkish, Arabic, Kazak, 
Vietnamese, Chinese, Korean, Japanese and Thai.
Menu position
This function is used to change the position of the On-
Screen Menu.
Press ▲▼ to select [Menu position].1 ) 
Press the  button to change 2 ) 
the position.
The Menu position changes each time you  z
press  button as follows:
the center → the bottom left → the bottom right → the 
top left → the top right → the center......
Auto setup
Press ▲▼ to select [Auto setup].1 ) 
Press ► or the  button.2 ) 
Press ▲▼ to select these functions as 3 ) 
follows:
 JInput search
      This function detects the input signal 
      automatically. When a signal is found, the search 
      will stop.
OffInput search will not work
On 1Input search works*1
On 2Input search works*2
● When pressing the  button on the*1 :  
    remote control.
● When turning on the projector by pressing the  *2 : 
   <  > button on the remote control.         
 ● When pressing the  button on the  
    remote control. 
● When the current input signal is cut off.*   
 * If the AV mute or Freeze function is active, cancel  
   it to activate the Input search. It is also unavailable  
   when On-Screen menu is displayed.
Auto PC adj. J
OnEnables Auto PC adjustment *1
OffDisables Auto PC adjustment
When pressing the  button on *1 : 
the remote control. 
Note
[Input search] and [Auto PC adj.] cannot be set [Off] at  z
the same time. 
						

							Setting
ENGLISH - 49
Settings
Background
Select the background screen for when no input signal 
is detected.
Press ▲▼ to select [Background].1 ) 
Press the  button.2 ) 
Press ▲▼ to switch3 )  between each 
option as below.
BlueBlue colored background.
UserThe logo transferred by "Logo
Transfer Software *1 " is projected.
BlackBlack colored background.
" Logo Transfer Software" is included on the *1 : 
supplied CD-ROM.
Display
This function decides whether to display On-Screen 
Displays.
Press ▲▼ to select [Display].1 ) 
Press the  button.2 ) 
Press ▲▼ to switch3 )  between each 
option as below.
OnShow all the On-Screen 
displays *1
Countdown 
off
Show the input image instead 
of the countdown when turning 
on the projector *2
OffHide the On-Screen Displays *3
Use this function when you want to project *1 : 
images after the lamp becomes bright enough. 
The factory default setting is in this option.
Use this function when you want to project the *2 : 
image as early as possible even when the lamp 
is not bright enough. 
Hide the On-Screen Displays except;  *3 : 
● On-Screen Menu. 
● [Power off ?]  
● [P-timer] display. 
● No signal for [Power management]   
● [Please wait ...]  
●   
Arrows for the [True] function and the [Digital 
Zoom +/-] function in the Screen Menu.
*4 : 
*5 : 
*6 : 
*7 : 
Logo
This function allows you to customize the screen logo 
with [Logo select], [Logo PIN code lock] and [Logo 
PIN code change] functions.
Press ▲▼ to select [Logo].1 ) 
Press ► or the  button.2 ) 
Press ▲▼ to choose the desired item.3 ) 
Logo select J
This function decides on the starting-up display from 
among following options.
OffShow the countdown display only.
DefaultShow the factory-set logo.
UserThe logo transferred by "Logo
Transfer Software *1 " is projected.
 " Logo Transfer Software" is included on the *1 : 
supplied CD-ROM.
Logo PIN code lock J
This function prevents an unauthorized person from 
changing the screen logo.
OffThe screen logo can be changed freely 
from the Logo Menu.
OnThe screen logo cannot be changed 
without a Logo PIN code.
Note
If you want to change the Logo PIN code lock setting,  z
press the  button and the Logo PIN code 
dialog box appears. Enter a Logo PIN code by following 
the steps below. The initial Logo PIN code is set to “4321” 
at the factory. 
						

							Setting
50 - ENGLISH
Settings
Logo PIN code change J
Logo PIN code can be changed to your desired four-
digit number.
Press ▲▼ to select [Logo PIN code 1 ) 
change].
Press the  button.2 ) 
Current logo PIN code dialog box appears. z
Press ▲▼ to enter the current code.3 ) 
The New Logo PIN code input dialog box  z
appears. Set a new Logo PIN code, a 
confirmation box appears, choose [Yes] to set 
the new Logo PIN code.
Attention
Be sure to note the new Logo PIN code and keep it on  z
hand. If you lost the number, you could no longer change 
the Logo PIN code setting.
HDMI setup
This function is only used for HDMI input source.
Press ▲▼ to select [HDMI setup].1 ) 
Press ► or the  button.2 ) 
The names for the output setting of Digital R/G/ z
B vary from equipment to equipment.
Image J
NormalWhen the output of Digital R/G/B
equipment is set to Standard.
EnhancedWhen the output of Digital R/G/B
equipment is set to Enhanced.
Sound J
HDMIWhen Digital input source is input,
Sound is set to HDMI.
Computer  When DVI input source is changed 
to HDMI input source, Sound is set 
to Computer .
Attention
For details, refer to the operating instructions of your  z
Digital R/G/B equipment.
Terminal
The COMPUTER IN 2/MONITOR OUT terminal on 
the back of the projector is switchable for computer 2 
input or monitor output.
Press ▲▼ to select [Terminal] and 1 ) 
then press the  button.
Press ▲▼ to switch the item.2 ) 
Computer 2Computer input
Monitor outMonitor out
Note
Terminal function is not available when selecting  z
[Computer 2] to the input source. Change the input 
source to the others (HDMI or Computer 1 or Video) so 
that the Terminal function will be available.
Power management
For reducing power consumption as well as 
maintaining the lamp life, the Power management 
function turns off the projection lamp when the 
projector is not operated for a certain period.
Press ▲▼ to select [Power 1 ) 
management].
Press ► or the  button to 2 ) 
access the submenu.
Mode J
Press ▲▼ and then press the 1 ) 
 button to select one mode 
among the items as below.
Off[Power management] function is off.
ReadyWhen the lamp has been fully cooled 
down, the  
indicator changes to green blinking. 
In this condition, the projection lamp 
will be turned on if the input signal 
is reconnected or any button on the 
control panel or remote control is 
pressed.
Shut 
down
When the lamp has been fully cooled 
down, the power will be turned off.
Timer J
Press ▲▼ to select [Timer] and then 1 ) 
press the  button.
Press ▲▼ to set the Timer(1~30min).2 )