Panasonic LCD Projector PT-P1SDU Operating Instructions

ENGLISH
R
Before operating this product, please read the instructions carefully and save this
manual for future use.
LCD Projector 
Operating Instructions
Model No.
PT-P1SDU
TQBJ 0184
Commercial Use
POWER
AUTO
SETUPINPUT MENU
SHUTTER
VOLUME
ENTER
R O TAT E RETURNENTERSTD 

2-E
NGLISH
ENGLISH
-3
Preparation
IMPORTANT SAFETY NOTICE Dear Panasonic Customer:This instruction booklet provides all the necessary operating information that
you might require. We hope it will help you to get the most out of your new
product, and that you will be pleased with your Panasonic LCD projector.
The serial number of your product can be found on its bottom. You should note
it in the space provided below and retain this booklet in case service is required.Model number:  PT-P1SDU Serial...

ENGLISH
-5
Preparation
4-E
NGLISH
ContentsPreparationIMPORTANT SAFETY NOTICE ...2
Precautions with regard to 
safety .........................................5
Accessories .................................9
Before use ..................................10
Read this page first ...................12
Location and function of each
part ...........................................14Getting startedSetting-up ...................................20
Projection methods, Projector
position, Projection distances...

ENGLISH
-7
Preparation
6-E
NGLISH
Do not do anything that might damage the power cord or the power
cord plug.
BDo not damage the power cord, make any modifications to it, place it near
any hot objects, bend it excessively, twist it, pull it, place heavy objects on
top of it or wrap it into a bundle.
BIf the power cord is used while damaged, electric shocks, short-circuits or
fire may result.
BAsk an Authorized Service Center to carry out any repairs to the power
cord that might be necessary.
Do not...

ENGLISH
-9
Preparation
8-E
NGLISH
Do not place any heavy objects on top of the projector.
BFailure to observe this may cause the projector to become unbalanced
and fall, which could result in damage or injury.
Do not short-circuit, heat or disassemble the batteries or place them
into water or fire.
BFailure to observe this may cause the batteries to overheat, leak, explode
or catch fire, and burns or other injury may result.
When inserting the batteries, make sure the polarities (+ and -) are
correct.
B...

ENGLISH
-11
Preparation
10-E
NGLISH
Before useCaution when moving the projectorBe sure to check that the lens cover has been attached to the lens
before moving the projector.
The projection lens is extremely susceptible to vibration and shocks. When
moving the projector, use the accessory softcase. When placing the projector
inside the softcase, position it so that the lens is facing upward.
Do not put anything else in the softcase other than the projector, cables,
remote control unit and the SD memory...

ENGLISH
-13
Preparation
12-E
NGLISH
Read this page firstWhen you turn on the power for the first time after purchase, the
“LANGUAGE SETUP” and “OTHER SETUP” menus will be displayed. Adjust
the settings according to the place and situation where you are using the
projector.
These menus will be displayed only when you turn on the power for the first
time, but you will be able to change the settings by operating the on-screen
menus. (Refer to page 40 for details.)LANGUAGE SETUP menu
FRONT/REARThis setting...

ENGLISH
-15
Preparation
14-E
NGLISH
Location and function of each part#Projector control panel (page 16)
$SD memory card slot
%Back adjustable leg (page 27)
&Illumination sensor and LAMP/TEMP indicators (page 16)
'Remote control signal receptor (page 24)
(Lens cover (page 62)
Use the projector with the lens cover attached.
)Front leg adjuster button (page 27)
This button is used to unlock the front adjustable leg. Press to adjust the
angle of tilt of the projector.
*Air inlet port
Do not cover this...

ENGLISH
-17 16-E
NGLISH
Preparation
Remote control unitProjector control panel 
$SD operation buttons (pages 18 and 35)
These buttons are used for operation when the SD selection screen is being
displayed and when files in the SD memory card are being played back.
%POWER button (pages 26, 28 and 29)
This button is used to turn the power on and off. This button on the
projector illuminates red when the projector is in standby mode, and it
illuminates green when a picture starts to be projected.
&INPUT...

ENGLISH
-19 18-E
NGLISH
SD operation buttons 
R O TAT E RETURN
ENTER
#SD 
/
button
These buttons are used to select folders and files on the SD selection
screen.

Press the SD  button to switch to the previous file, and the SD 
button to switch to the next file.
You can start and stop the slide show by holding down the SD  button.
$SD ENTER button
This button is used to accept the selection made on the SD selection
screen.
%SD RETURN button
This button is used to return to the previous screen.
&SD ROTATE...