Panasonic LCD Projector Pt Lx22E Operating Instructions

							Basic operations by using the remote control
ENGLISH - 31
Basic Operation
Press  button on the remote 
control.
Note
For details, see “Lamp Power” of "Setting" under Main  z
menu. (Æpage 50)
Using the D.ZOOM buttons
This function allows you to enter to the Digital zoom 
+/– mode.
    Buttons
Press  buttons on the 
remote control.
Note
For details, see "Screen" of Main menu. ( zÆpage 45) 
Using the IMAGE button
This function allows you to select a desired image 
mode of the screen.
 Button
Press  button on the remote control to select 
the desired image mode among [Dynamic], [Standard], 
[Real], [Cinema], [Blackboard (Green)], [Colorboard], 
[Image 1], [Image 2], [Image 3] and [Image 4]. 
						

							32 - ENGLISH
Settings
Menu Navigation
Navigating through the menu
Operating procedure J
Press the  button.1 ) 
The Main Menu screen appears.
Press ▲▼ to select the Main Menu 2 ) 
item.
Select the desired item from the 7 items: [Input], 
[PC adjust], [Image select], [Image adjust], 
[Screen], [Setting], [Information]. The selected 
item is highlighted with an orange cursor and the 
submenu of the selected item appears on the 
right.
Press ► or the  button.3 ) 
The submenu appears so that you can select the 
sub-menu item.
Press ▲▼ to select the desired sub-4 ) 
menu item.
Press the button or press ► 5 ) 
to enter the desired item.
Press ▲▼ ◄► to set or adjust the 6 ) 
parameter values.
Press ◄ to return the previous menu. 7 ) 
Press the  button to exit the 
menu display.
Note
Some items may not be adjusted or used for certain  z
signal formats input to the projector. The MENU items 
that cannot be adjusted or used are shown in gray 
characters, and they cannot be selected.
Some items can be adjusted even if signals are not input. z
See page 33 and 34 for details on the items of sub-menu. z 
						

							Menu Navigation
ENGLISH - 33
Settings
Main menu
The main menu consists of the following 7 menu 
items.
When a main menu item is selected, the screen 
changes to a submenu selection screen.
Input
PC adjust
Image select
Image adjust
Screen
Setting
Information
Sub menu
The sub-menu screen of the selected main menu 
appears, and you can set and adjust the various items 
in the submenu.
 JInput [  ]
Sub-menu itemFactory 
defaultPage
Computer 1 RGB35
Video -35
PC adjust [  J ]
Sub-menu itemFactory 
defaultPage
AUTO PC adj.-  37
Fine sync.-  38
Total dots-  38
Horizontal-  38
Vertical-  38
Current mode- 39
Clamp- 39
Display area H- 39
Display area V- 39
Reset - 39
Mode free- 39
Store - 39
Note
This function will be available when the input source   z
come from computer.
 JImage select [  ]
Sub-menu itemFactory 
defaultPage
Dynamic-40
Standard- 40
Real- 40
Cinema- 40
Blackboard(Green)-40
ColorboardRed40
Image 1-4-40 
						

							Menu Navigation
34 - ENGLISH
Settings
Image adjust [  ]
Sub-menu itemFactory defaultPage
Contrast3241
Brightness3241
Color3241
Tint3241
Color temp.Mid41
Red3242
Green3242
Blue3242
Sharpness842
Gamma842
Noise reduction*1L142
ProgressiveL143
Reset-43
Store- 43
When input video signal to the projector, these *1 : 
functions will be available.
Screen [  J ]
Sub-menu itemFactory defaultPage
Normal - 44
Full - 44
Wide (16:9)- 44
Zoom- 44
True*1- 44
Custom- 44
Custom adj.- 44
Digital zoom + *1- 45
Digital zoom - *1- 45
KeystoneStore 45
CeilingOff 45
RearOff 45
Reset- 45
When input computer signal to the projector, these *1 : 
functions will be available.
Setting [  J ]
Sub-menu itemFactory defaultPage
LanguageEnglish46
Menu positionCenter46
Auto setup- 46
BackgroundBlue47
DisplayOn47
Logo-47
Power managementShut down48
Direct onOff48
Standby modeEco48
Sub-menu itemFactory defaultPage
P-timerCount up48
Closed captionOff49
Lamp powerNormal50
Remote controlALL50
Security-50
FanL251
Fan controlOff51
Video delay control Off51
Lamp runtime-51
Filter counter-52
Warning log-52
AMX D.D.Off52
Factory default-52
Information [  J ]
Sub-menu itemFactory defaultPage
Input-53
System-53
H-sync freq.-53
V-sync freq.-53
Screen-53
Language-53
Lamp power-53
Lamp runtime-53
Power management-53
Key lock- 53
PIN code lock-53
Remote control-53
Serial number-53 
						

							ENGLISH - 35
Settings
Input menu
Select [Input] from the Main Menu (see 
“Navigating through the menu” on page 32), 
then select the item from the sub-menu.
Remote ControlControl Panel
 Computer 1: RGB/Component 
/RGB (Scart) /S-video
Press ▲▼ to select [Computer 1]. 1 ) 
Press ► to access the submenu.2 ) 
Press ▲▼ to select [RGB], 3 ) 
[Component] , [RGB(Scart)] or 
[S-video].
Press the  button.4 ) 
When Computer is selected, Component,  z
[RGB(Scart)] or [S-video] can be available. 
 JComputer System Selection
This projector automatically tunes to various types 
of computers with its Multi-scan system and Auto 
PC Adjustment. If a computer is selected as a signal 
source, this projector automatically detects the signal 
format and tunes to project a proper image without 
any additional settings. (Signal formats provided in 
this projector are shown on pages 65-67.)
      When the projector can not recognize the                                                                                                                                              
                connected signal conforming to the                         
               provided PC Systems, Auto is displayed  
               on the System Menu box and the [Auto PC  
              adjustment] function works to display proper  
               images.  If the image is not projected   
               properly, a manual adjustment is required.
                There is no signal input from the computer.                                                                                                                                        
                Check the connection between your                                                                                                                                             
                computer and the projector.
                The preset system is manually adjusted in                                                                                                                                               
                the PC adjust Menu. The adjusted data can                                                                                                                                              
                be stored in Mode 1-10. 
                PC Systems provided in this projector                                                                                                                                        
                is chosen. The projector chooses a proper                                                                                                                                           
                system provided in the projector and                                                                                                                                              
                displays it.
* Mode 1 and SVGA 1 are examples.  
Press ▲▼ to select [System].1 ) 
Press ► or the  button to 2 ) 
access the submenu.
Press ▲▼ to select the desired system.3 ) 
Video
Press ▲▼ to select [Video] and then 
press the  button.
 JVideo System Selection
Video or S-video
Auto
The projector automatically detects an incoming video 
system, and adjusts itself to optimize its performance.
When [Video System] is [PAL-M] or [PAL-N], select 
the system manually.
PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N
If the projector cannot reproduce proper video image, 
select a specific broadcast signal format from among 
[PAL], [SECAM], [NTSC], [NTSC 4.43], [PAL-M] and 
[PAL-N].
Component
Auto
The projector automatically detects an incoming video 
signal, and adjusts itself to optimize its performance.
COMPONENT VIDEO SIGNAL FORMAT
If the projector cannot reproduce proper video image, 
select a specific component video signal format 
among [480i], [576i], [480p], [576p], [720p], [1035i] 
and [1080i].
AUTO
- - - -
Mode 1
SVGA 1 
						

							Input menu
36 - ENGLISH
Settings
Press ▲▼ to select [System].1 ) 
Press ► or the  button to 2 ) 
access the submenu.
Press ▲▼ to select the desired system.3 ) 
Attention
When the Input Search function is set to [On1] or [On2]  z
in the [Auto setup] function, the input signal will be 
searched automatically. 
The AV System Menu cannot be selected when selecting  z
[RGB (Scart)]. 
						

							AUTO PC adjust 
ENGLISH - 37
Settings
AUTO PC adjust 
Select [PC adjust] from the Main Menu (see 
“Navigating through the menu” on page 32), 
then select the item from the sub-menu.
Remote ControlControl Panel
AUTO PC adj.
[Auto PC adjustment] function is provided to 
automatically adjust [Fine sync], [Total dots], 
[Horizontal] and [Vertical] positions to conform to your 
computer.
Press ▲▼ to select [AUTO PC adj.] and 
then press the  button. 
[Please wait...] z appears while the Auto PC 
adjustment is in process.
To store adjustment parameters
The adjusted parameters from the [Auto PC 
adjustment] can be stored in the projector. Once the 
parameters are stored, the setting can be done just by 
selecting a Mode (1–10) in the PC System Menu (see 
page 35). See also [Store] on page 39.
Attention
[Fine sync], [Total dots], [Horizontal] and [Vertical]  z
position of some computers cannot be fully adjusted 
with the [Auto PC adjustment] function. When the image 
is not provided properly with this operation, manual 
adjustments are required (Æpages 38-39). 
The Auto PC adjustment cannot be operated when [480i],  z
[576i], [480p], [576p], [720p], [1035i] or [1080i] is selected 
in the PC System Menu (Æpage 35). 
						

							Manual PC adjust 
38 - ENGLISH
Settings
Manual PC adjust 
Select [PC adjust] from the Main Menu (see 
“Navigating through the menu” on page 32), 
then select the item from the sub-menu.
Remote ControlControl Panel
Some computers employ special signal formats 
which may not be tuned by Multi-scan system of this 
projector. Manual PC adjustment enables you to 
precisely adjust several parameters to match those 
signal formats. The projector has 10 independent 
memory areas to store those parameters manually 
adjusted. It allows you to recall the setting for a 
specific computer.
Fine sync
Press ▲▼ to select [Fine sync].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the value.3 ) 
The value can be adjusted from 0 to 31. z
Total dots
Press ▲▼ to select [Total dots].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the value.3 ) 
Horizontal
Press ▲▼ to select [Horizontal].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the horizontal 3 ) 
picture position.
For horizontal (right and left)  J
adjustment
OperationAdjustment
Press ◄.
The picture 
position 
moves to the 
right.
Press ►.
The picture 
position 
moves to the 
left.
Vertical
Press ▲▼ to select [Vertical].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the vertical picture 3 ) 
position.
For vertical (up and down)  J
adjustment
OperationAdjustment
Press ►.
The picture 
position 
moves up.
Press ◄.
The picture 
position 
moves down. 
						

							Manual PC adjust 
ENGLISH - 39
Settings
Current mode
Press ▲▼ to select [Current mode].1 ) 
Press ► or the  button 2 ) 
to enter the next submenu to show 
H-sync freq. and V-sync freq. of the 
connected computer.
Clamp
Press ▲▼ to select [Clamp].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the clamp level.3 ) 
When the image has dark bars, try this  z
adjustment.
Display area H
Press ▲▼ to select [Display area H].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the horizontal area 3 ) 
displayed by this projector.
Display area V
Press ▲▼ to select [Display area V].1 ) 
Press the  button to display 2 ) 
the dialog box.
Press ◄► to adjust the vertical area 3 ) 
displayed by this projector.
Reset
To reset the adjusted data, all adjustments will return 
to their previous figures.
Press ▲▼ to select [Reset].1 ) 
Press the  button.2 ) 
A confirmation box appears and then select [Yes]. z 
Mode free
Press ▲▼ to select [Mode free].1 ) 
Press ► or the  button to 2 ) 
enter the next submenu.
Move the highlight to the mode that you want to  z
clear and then press the  button.
Store
Press ▲▼ to select [Store].1 ) 
Press ► or the  button to 2 ) 
enter the next submenu.
Move the highlight to one of the Modes 1 to 10  z
in which you want to store, and then press the 
 button. 
						

							40 - ENGLISH
Settings
Image select 
Select [Image select] from the Main Menu (see 
“Navigating through the menu” on page 32), 
then select the item from the sub-menu.
Remote ControlControl Panel
Dynamic
For viewing pictures in a bright room.
Press ▲▼ to select [Dynamic] and then 
press the  button.
Standard
Normal picture mode preset on the projector.
Press ▲▼ to select [Standard] and then 
press the  button.
Real
Picture mode with improved halftone for graphics. 
Press ▲▼ to select [Real] and then press 
the  button.
Cinema
Picture mode adjusted with fine tone.
Press ▲▼ to select [Cinema] and then 
press the  button.
Blackboard(Green)
For the image projected on a blackboard.
Press ▲▼ to select [Blackboard(Green)] 
and then press the  button.
This mode helps enhance the image projected  z
on a blackboard. This is mainly effective on a 
green colored board, not truly effective on a 
black colored board.
Colorboard
For the image projected on a colorboard.
Press ▲▼ to select [Colorboard].1 ) 
Press ► or the  button to 2 ) 
display the submenu.
At the time of simple projection on the colored  z
wall, you can get the close color image to the 
color image projected on a white screen by 
selecting the similar color to the wall color from 
the preset four colors.
Image 1-4
For viewing with the user preset image mode in the 
Image adjust Menu. This Image memory is provided 
in each computer, component and video input source.
Press ▲▼ to select [Image 1-4] and then 
press the  button.