Panasonic LCD Projector Pt Lw330 Operating Instructions

							ENGLISH - 41
button
1) Press the  button on the remote control.
 
f It will switch each time you press the button, [  (Normal)] → [  (Eco 1)] →[  (Eco 2)].
Note
 
f For details, please refer to the [Setting] menu → [Lamp control] ( x page 56).
Using the digital zoom function
(Only for still image-based computer (RGB) and still image-based HDMI signals input)
You can enlarge the center area. You can also change the location of the area to be enlarged. 
 buttons
1) Press the  or < D.ZOOM -> button on the remote control.
 
f The [D. zoom] individual adjustment screen is displayed. 
 
f Press asqw  on the remote control to move the display position during zoom in.  
[D.zoom] individual adjustment 
screen  Operation
AdjustmentAdjustment range
Press the  button. Increases magnification.
0 ~ 33
Press the  button. Decreases magnification.
While the screen is displayed and 
the image is expanded. Press the as buttons.
Moves the area to the top or 
the bottom.
-
Press the qw buttons. Moves the area to the left or 
the right.
Note
 
f When the input signals change during [D. zoom], the adjusted value of the digital zoom will be cancelled.
 
f When no signal input, the key operation is invalid and the icon 
 will appear.
 
f You can also press  asqw buttons on the control panel to move the display position during zoom in.
Controlling the volume of the speaker
You can adjust the volume of the audio output from the build-in speaker and the  terminal.
buttons
1) Press the  or  button on the remote control.
 Increases the volume.
 Decreases the volume.
Switching the image mode
This function allows you to switch the image mode.
button
1) Press the  button on the remote control.
 
f It will switch each time you press the button, [Dynamic] → [Standard] →[Cinema] → [Blackboard(Green)] → 
[Colorboard] → [User image] → [Dynamic] →....
Note
 
f For details, please refer to the [Color adjust] menu → [Image mode] ( x page 52).
Chapter 3   Basic Operations - Basic operations by using the remote cont\
rol  
						

							42 - ENGLISH
Using the mute function
This button allows you to turn off the audio output temporarily.
button
1) Press the  button on the remote control. 
 
f The audio turns off.
2)  Press the  button again.
 
f The audio turns on.
Using the Daylight View Lite function
The Daylight View Lite function improves the vividness of the image even if it is proj\
ected under a bright light.
button
1)  Press the  button on the remote control. 
 
f The Daylight View Lite function will be switched enable/disable each time you press th\
e button.
Note
 
f For details, please refer to the [Color adjust] menu → [Daylight V iew] (x page 54).
Chapter 3   Basic Operations - Basic operations by using the remote cont\
rol  
						

							ENGLISH - 43
Chapter 4   Settings
This chapter describes the settings and adjustments you can make using t\
he on-screen menu.  
						

							44 - ENGLISH
Menu Navigation
The on-screen menu (Menu) is used to perform various settings and adjustments of the projector.
Navigating through the menu
Operating procedure
 button
1) Press the  button on the remote control or the control panel.
 
f The main menu screen appears.
2)  Press as to select an item from the main menu.
 
f The selected item is highlighted in orange.
3)  Press the  button.
 
f The submenu is displayed, and submenu items become selectable.
(there is no lower menu under the submenu) (there is lower menu under the submenu)
 
f Please perform step 4).
 
f If there is lower menu under the submenu,  will be 
displayed. (except for [System] in [Display] menu)
 
f Please perform step 7).
4)  Press as to select a sub-menu item, press the  button.
 
f If the selected submenu can be set or adjusted,  will be displayed. 
Chapter 4   Settings - Menu Navigation  
						

							ENGLISH - 45
5) Press as to switch or adjust settings.
 
f Some items will switch in order as follows each time you press as.
ABC
6)  Press the  button or the  button.
 
f The changed settings or the adjusted value is confirmed. 
7)  Press as to select a sub-menu item, press the  button.
 
f Switches to the next layer of the menu screen.
8)  Press the  button.
 
f If the selected item can be set or adjusted,  will be displayed.
9)  Press as to switch or adjust settings.
 
f Some items will switch in order as follows each time you press as.
ABC
 
f The selected item will be displayed in a check  mark.
10)  Press the  button or the  button.
 
f The changed settings or the adjusted value is confirmed. 
Note
 
f Pressing the  button while the menu screen is displayed returns to the previous menu or exits the menu screen.
 
f Some items may not be adjusted or used for certain signal formats to be \
input to the projector. The menu items that cannot 
be adjusted or used are shown in gray characters, and they cannot be sel\
ected. 
 
f Some items can be adjusted even if signals are not input.
 
f For menu items, refer to “Main menu” (x page 45) and “Sub-menu” ( x page 46).
Main menu
The following items are in the main menu.
When a main menu item is selected, the screen changes to a submenu selection screen.
Main menu itemPage
[Display]49
[Color adjust]52
[Setting]55
[Expand]59
[Memory Viewer]71
[Info.]73
Chapter 4   Settings - Menu Navigation  
						

							46 - ENGLISH
Sub-menu
The sub-menu screen of the selected main menu appears, and you can set a\
nd adjust the various items in the submenu.
[Display]  
Sub-menu itemFactory default Page
[Auto PC adj.]*1- 49
[Fine sync]*1- 49
[H Position]*1- 49
[V Position]*1- 50
[H.Size]*1- 50
[Aspect] [Normal]50
[Project way] [Front]51
[Menu position] [Upper left]51
[Background display] [Blue]51
[System] -51
*1  Only for computer signals.
[Color adjust]  
Sub-menu item Factory default Page
[Image mode] [Standard]52
[Contrast] [32]52
[Brightness] [32]52
[Color]
*1[32] 53
[Tint]*1[32] 53
[Color temp.] [Mid]53
[Red] [32]53
[Green] [32]53
[Blue] [32]53
[Sharpness] [8]54
[Daylight View] [Off]54
*1  Only for movie-based signals.
Note
 
f The factory default settings may vary depending on the image mode.
[Setting]  
Sub-menu item Factory default Page
[On start] [Off]55
[Standby mode] [Eco]55
[High land] [Off]55
[Lamp control] [ 
 (Normal)]56
[Cooling fast] [Normal]56
[Closed caption] [Off]56
[Key lock] [ 
 (Off)]57
[Iris] [On]57
[Terminal]
*1[Computer 2] 57
[Sound] -57
[HDMI Setup] -58
*1  Only for PT-LW330, PT-LW280, PT-LB360 and PT-LB330.
[Expand]  
Sub-menu item Factory default Page
[Language] [English]59
Chapter 4   Settings - Menu Navigation  
						

							ENGLISH - 47
Sub-menu itemFactory default Page
[Auto setup] -59
[Keystone] [Store]61
[Logo] -64
[Security] -66
[Power management] [Shut down]67
[Filter counter] -68
[Test pattern] [Off]68
[Network] -69
[Remote control] [All]70
[Factory default] -70
[Memory Viewer]*1  
Sub-menu item Factory default Page
[Set Slide] -71
[Slide Transition Effect] [Slide Right]71
[Sort Order] [Name Order]71
[Rotate] [No Rotate]71
[Best Fit] [Off]72
[Repeat] [Off]72
[Apply] -72
*1  Only for PT-LW330, PT-LW280, PT-LB360 and PT-LB330.
[Info.]  
Details (x page 73) Note
 
f Some items may not be adjusted or used for certain signal formats to be \
input to the projector.  
The menu items that cannot be adjusted or used are shown in gray charact\
ers, and they cannot be selected.
 
f Sub-menu items and factory default settings differ depending on the selected input terminal.
Chapter 4   Settings - Menu Navigation  
						

							48 - ENGLISH
[Input] menu
To select the input source directly by pressing the input selection butto\
ns on the remote control or to select the 
input source in the [Input] screen by pressing the  button \
on the control panel.
Switching the input source
When using the remote control
1) Press the input selection (, , , ,\
 ) buttons. 
 
f To project the corresponding input signal of the selected terminal.
 Switches to Computer 1/Component input.
 Switches to Computer 2 input.
 Switches to HDMI input.
 Switches to Video/S-video input.
Switches to Memory Viewer/USB Display input.
When using the control panel
1)  Press the  button.
 
f The [Input] screen is displayed.
2)  Switches the input source by pressing  as to select one item and then press the  button.
 
f To project the corresponding input signal of the selected terminal.
[Computer]*1Switches to Computer input.
[Computer 1]
*2Switches to Computer 1 input.
[Computer 2]
*2Switches to Computer 2 input.
[HDMI] Switches to HDMI input.
[Component] Switches to YP
BPR/YCBCR input.
[Video] Switches to Video input.
[S-video] Switches to S-video input.
[Memory Viewer]*2Switches to Memory Viewer input.
[USB Display]*2Switches to USB Display input.
*1  Only for PT-LB300 and PT-LB280.
*2  Only for PT-LW330, PT-LW280, PT-LB360 and PT-LB330.
Note
 
f [Computer 2] is not available when [Setting] menu → [Terminal] is set to [Monitor out]. PT-LW330, PT-LW280, 
PT-LB360, PT-LB330
PT-LB300, PT-LB280
Chapter 4   Settings - [Input] menu  
						

							ENGLISH - 49
[Display] menu
On the menu screen, select [Display] from the main menu, and select an i\
tem from the sub-menu.
Refer to “Navigating through the menu” (x page 44) for the operation of the menu screen.
 
f After selecting the item, press as to set.
[Auto PC adj.]
(Only for computer signals input)
When input the computer (RGB) signals, the image may be moved up, down, left or right such as flickering, press the  button to adjust [Fine sync], [H position], [V position] and [H.Size] automatically in optimal state. Set the image to get 
an optimal state to match with the audio-visual surroundings in which th\
e projector is used.
1)  Press as to select [Auto PC adj.]. 
2)  Press the  button.
 
f [Please wait...] screen is displayed, the Auto PC adj. function will be executed.
Note
 
f The projector executes the Auto PC adj. automatically when the computer signals input the projector for the first time.
 
f Automatic adjustment may not work depending on the model of the computer\
 and the input signal.
 
f The [Auto PC adj.] cannot be operated when [480i], [576i], [480p], [576p], [720p], [1080i] or [1080p] is selected in the 
[Display] menu → [System], or when the signal is coming from the  terminal.
[Fine sync]
(Only for computer signals input)
You can adjust to achieve an optimal image when there is a flickering image or smeared outlines.
1)  Press as to select [Fine sync].
2)  Press the  button.
3)  Press as to adjust the level.
 
f The adjustment values are 0 to +31. Adjust so that the amount of interference is at a minimum.
Note
 
f Certain signals may not be adjustable.
 
f Optimal value may not be achieved if the output from the input computer is unstable.
 
f To project a signal with dot clock frequency with 162 MHz or higher, noise may not disappear even if [Fine sync] is adjusted.
 
f [Fine sync] cannot be adjusted when a digital signal is input.
[H Position]
(Only for computer signals input)
Move the image position horizontally if the image position projected on the screen is shifted even when the relative position of 
the projector and the screen is installed correctly.
1)  Press as to select [H Position].
2)  Press the  button.
3)  Press as to adjust the horizontal image position. Chapter 4   Settings - [Display] menu  
						

							50 - ENGLISH
OrientationOperation Adjustment
Horizontal (left and  right) adjustment. Press the a button.
The image position moves to the right.
Press the s button.The image position moves to the left.
Note
 
f [H Position] is not available while the image is expanded in the digital zoom function.
[V Position]
(Only for computer signals input)
Move the image position vertically if the image position projected on th\
e screen is shifted even when the relative position of the 
projector and the screen is installed correctly.
1)  Press as to select [V Position].
2)  Press the  button.
3)  Press as to adjust the vertical image position.
Orientation Operation Adjustment
Vertical (up and down)  adjustment. Press the a button.
The image position moves up.
Press the s button.The image position moves down.
Note
 
f [V Position] is not available while the image is expanded in the digital zoom function.
[H.Size]
(Only for computer signals input)
Use this function to adjust and minimize the effect of interference caused by projection of patterns consisting of vertical stripes.
The projection of the vertical striped pattern may cause cyclic patterns (noise).  Adjust so that the amount of interference is at a 
minimum.
1)  Press as to select [H.Size].
2)  Press the  button.
3)  Press as to adjust the level.
 
f The adjustment values are -15 to +15.
Attention
 
f Set it before adjusting [Fine sync].
[Aspect]
Provide the image to fit the screen size while maintaining the aspect ratio of the input signal.
1)  Press as to select [Aspect]. 
2)  Press the  button.
3)  Press as to switch the item.
 
f The items will switch each time you press the button.
[Normal] Projects the image at the maximum size while maintaining the aspect ratio of the input signal.
[Wide] Projects the image at 16:9 aspect ratio.
Chapter 4   Settings - [Display] menu