Panasonic LCD Projector PT-LB90NTU PT-LB90U PT-LB78VU PT-LB75VU Operating Instructions

PICTURE menu
Settings
ENGLISH - 31
DAYLIGHT VIEW
You can keep the projected image bright and vivid 
even in well-lit rooms where the ambient light sources 
cannot be controlled, such as when a door opens or 
when window coverings fail to block out sunlight.Change setting
Change setting
AUTOONOFF
AUTO Automatic adjustment
ON Active
OFF Deactive
Remarks Do not cover the Ambient Luminance Sensor (
 
zALS) 
of the projector. The AUTO mode may not operate 
normally.
AUTO
 
z is not available when...

POSITION menu
Settings
32 - ENGLISH
POSITION menu
Navigating through the MENU (Æpage 27),  
select POSITION from the main menu and then   
select the required item from the sub-menu.
Set the selected item with ▲▼◄► buttons.
 
z
Remote controlControl panel
REALTIME KEYSTONE
If the projector is aligned non-perpendicularly to the 
screen, or if the projection screen has an angled 
surface, the keystone will be corrected automatically.
Change setting
Change setting
ON Active
OFF Deactive
KEYSTONE
If you need...

POSITION menu
Settings
ENGLISH - 33
OVER SCAN
Use this function when characters or pictures are 
cropped near the periphery of the projected image.
(Available with signals of S-VIDEO/VIDEO/RGB  
(Moving image)/ YP
BPR only)
Zoom out
Zoom in
Setting range: 0 to +3
 
z
Remarks
OVER SCAN
 
z is not available when network signals 
are input.
ASPECT
You can switch the aspect ratio manually when needed. 
Selectable options vary according to input signal. 
Change setting
Change setting
AUTO4:316:9
THROUGH H...

POSITION menu
Settings
34 - ENGLISH
S4:3 
J
When a standard signal *1 is input, the input signal 
will be sized down 75% and projected.  S4:3 mode 
is effective when projecting 4:3 image onto a 16:9 
screen.
Input signal: XGA
 
z
Image:   Panel:  Screen: 
THROUGH 
J
The image will be projected without any size 
adjustment.
Input signal: NTSC
 
z
Image:   Panel:  
A standard signal has an aspect ratio of 4:3 or 5:4.
*1: 
NoteIf you project a 4:3 image onto a 16:9 screen, 
 
z
the image may distort or some...

LANGUAGE menu
Settings
ENGLISH - 35
LANGUAGE menu
Navigating through the MENU (Æpage 27),  
select LANGUAGE from the main menu and 
then display the sub-menu.
Select the required language with▲▼buttons  
 
z
and press the ENTER button to set.
Remote control
Control panel
PICTURE
POSITION
DISPLAY OPTION
PROJECTOR SETUP
SECURITY
NETWORK
LANGUAGE
PICTURE
POSITION
DISPLAY OPTION
PROJECTOR SETUP
SECURITY
NETWORK LANGUAGE
The set language is highlighted. 

DISPLAY OPTION menu
Settings
36 - ENGLISH
DISPLAY OPTION menu
Navigating through the MENU (Æpage 27),  
select DISPLAY OPTION from the main menu 
and then select the required item from the   
sub-menu.
Set the selected item with◄►buttons.
 
z
Remote controlControl panel
ON-SCREEN DISPLAY
You can set the on-screen display.
Change setting
Change setting
 
JINPUT GUIDE
When you change the input method, the guidance 
appears in the upper right corner of the screen. The 
following display methods are...

DISPLAY OPTION menu
Settings
ENGLISH - 37
STARTUP LOGO
You can set to display the Panasonic logo, your own 
image or Pre-set letters, when starting up the projector.
Change settingChange setting
ONDisplay “Panasonic” logo
TEXT Display the original text
USER Display the image registered by 
user
OFF No display
Remarks If 
 
zTEXT is selected, the input letters are displayed 
when starting up the projector. You can display 
2 lines of original text which contain up to 40 
characters each.
If 
 
zUSER is...

DISPLAY OPTION menu
Settings
38 - ENGLISH
WIDE MODE
When projecting WIDE signals, switch to ON to display 
the image in well adjusted size (16:9, 16:10, 15:9)
.
Change setting
Change setting
AUTO Automatic setting
OFF For 4:3 signals
ON For WIDE signals
SXGA MODE
Switch to the SXGA setting when inputting SXGA signal.
Change settingChange setting
SXGA For normal projection
SXGA+ For projection when image is 
cropped
OTHER FUNCTIONS
You can perform some of the remote control button 
operations from the...

PROJECTOR SETUP menu
Settings
ENGLISH - 39
PROJECTOR SETUP menu
Navigating through the MENU (Æpage 27), select 
PROJECTOR SETUP from the main menu and 
then select the required item from the sub-menu.
Set the selected item with◄►buttons. 
z
Remote controlControl panel
STATUS
You can check the using status of the projector.
SIGNAL 
J
NAME: Name of input signal 
z
FREQUENCY: Scanning frequency of input  
z
signal
RUNTIME 
J
PROJECTOR: Display current usage time of  
z
projector
LAMP: Display current usage...

PROJECTOR SETUP menu
Settings
40 - ENGLISH
STANDBY MODE
You can change the standby mode setting.Change setting
Change setting
ECO The standby power is reduced to 
0.9 W to save power.
NORMAL The power of the projector can be 
turned ON and the audio output 
can be set active from controlling 
the computer connected via a 
wired LAN or a wireless LAN in the 
NORMAL mode.
LAMP POWER
You can adjust the power of the lamp to save electricity, 
prolong the lamp life and reduce the noise.
Change settingChange...