Panasonic LCD Projector PT-F100NTU PT-F100U Operating Instructions

Menu Navigation
ENGLISH - 31
Settings
Main menuSub-menuOptions ( * is default setting)Page
OPTION INPUT GUIDE DETAILED*SIMPLEpage 36
OFF
STARTUP LOGOON*OFF
page 36
USER
COMPUTER2 SELECT INPUT*OUTPUTpage 36
LAMP RUNTIMEpage 36
FILTER REMAININGpage 37
POWER OFF TIMER OFF*35 MIN.page 37
15 MIN. 40 MIN.
20 MIN. 45 MIN.
25 MIN. 50 MIN.
30 MIN. 60 MIN.
DIRECT POWER ON OFF*ONpage 37
CONTROL PANEL VALID*INVALIDpage 37
AUTO SETUP AUTO*BUTTONpage 37
SIGNAL SEARCH ON*OFFpage 37
INSTALLATION FRONT/DESK REAR/DESKpage...

ENGLISH - 32
Settings
PICTURE menu
Depending on the projection environment, you can use 
these preset parameter settings to optimize image 
projection. Press I H to cycle through the options.
You can adjust the contrast of the projected image. 
Adjust the BRIGHTNESS in advance if necessary.
You can adjust the brightness of the projected image.You can adjust the color saturation of the projected 
image.
You can adjust the skin tone in the projected image.
You can adjust the sharpness of the projected...

PICTURE menu
ENGLISH - 33
Settings
You can perform more detailed image adjustment 
manually.
JFor S-VIDEO/VIDEO signals
QTV-SYSTEM
When the video signal is changed, the setting 
switches automatically. You can switch the setting 
manually to match the video data. Press I H to 
cycle through the options.
QSTILL MODE
You can reduce the vertical flicker when projecting 
a still image.
 OFF: Deactive
 ON: Active
QNOISE REDUCTION
You can switch the automatic noise reduction 
system on/off. Press I H to select...

ENGLISH - 34
Settings
POSITION menu
If the projector is aligned non-perpendicularly to the 
screen, or if the projection screen has an angled surface, 
you can correct keystone.
 Setting range: -32 to +32
You can move the projected image for fine adjustment. 
Press I H to move horizontally and F G vertically.If you have interference patterns of the projected image, 
which is sometimes referred to as moire or noise, you 
can minimize it by pressing I H to adjust the clock 
frequency.
If you require...

POSITION menu
ENGLISH - 35
Settings
Q16:9
The squeezed signal will be projected in 16:9 ratio.
QS4:3
The input signal will be sized down 75 % and 
projected. S4:3 mode is effective when projecting 
4:3 image on to a 16:9 screen.
QAUTO
The S1 signal which contains an identifying signal 
will be detected and automatically project the 
image in proper ratio.When the input signal resolution is lower than the 
projector resolution, it will be projected at the projector 
resolution. You can deactivate the...

ENGLISH - 36
Settings
OPTION menu
When you change the input method, the guidance 
appears in the upper right corner of the screen. The 
following display methods are available. Press I H to 
cycle through the options.You can switch the logo on/off that is displayed when 
starting up the projector. Press I H to select the 
required option.
 ONActive
 OFFDeactive
 USERDisplay the original text
QEditing the original text
If you select USER, you can display the 2 lines of 
original text up to 40 characters...

OPTION menu
ENGLISH - 37
Settings
You can check the remaining amount of the ARF (Auto 
Rolling Filter). The color of the bar scale is indicating the 
condition of the ARF.
 Yellow The filter remaining amount is getting 
low.
 Red No more remaining.
You can set the off timer to switch off the POWER of the 
projector after a certain period of time automatically 
when no signal is detected. Press I H to select the 
required period from 15 to 60 minutes at intervals of 
5 minutes.
You can switch the...

Settings
OPTION menu
ENGLISH - 38
If you use the projector at high elevation, the HIGHLAND 
setting need to be ON to set the fan speed high. Press 
I H to select the required option.
 OFFThe fan speed is low.
 ONThe fan speed is high.
If the input signal contains closed captions, you can turn 
on the feature and switch the channels. Press I H to 
select the required option.
You can use the 7 different test patterns to adjust the 
focus of the image. See “Lens shift and positioning” on 
page 18. 
1. Press...

ENGLISH - 39
Settings
SECURITY menu
JEntering the SECURITY
Every time when you apply to the SECURITY 
menu, you will be asked to perform the password 
operation.
When you apply to the SECURITY menu before you 
change the password to your original, perform to input 
the following factory default password operation.
 Press F H G I F H G I and ENTER.
QAfter you change the password
When you apply to the SECURITY menu after you 
change the password to your original in the 
PASSWORD CHANGE menu, input the...

ENGLISH - 40
Settings
NETWORK menu
In NETWORK menu, the following items are available.
 WIRED LAN
 WIRELESS LAN
 NAME CHANGE
 PASSWORD CHANGE
 INPUT PASSWORD
 NETWORK STANDBY
 WEB CONTROL
 LIVE MODE CUT IN
 STATUS
 INITIALIZE
NOTE:
• The NETWORK menu is available only with 
PT-F100NTU.
• See more detailed instructions in the contents of the 
CD-ROM which is provided with the projector.
Remote control Control panel
 See “Navigating through the MENU” on page 29.
 See “Main menu and Sub-menu” on page 30....