Panasonic Lcd Monitor Tv Dvd Sd Receiver Cq Vd7700 Operating Instructions

							4731E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
4630E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
Manual Preset
Memory
Radio
Note:New stations overwrite existing saved stations after following this procedure.Touch and hold.
to  for more than 2 seconds.
Press and hold [1]to [6]on the remote
control for more than 2 seconds.
❑One-touch Selection of a Station
Up to 6 stations can be saved in each FM1, FM2, FM3 and AM preset station memories.
Operations
Panel
Remote
Auto Preset
Memory
Touch and hold for more than 2
seconds.
Press and hold [ENTER]for more than
2 seconds.
Preset Station
Calling
Touch to .
Press [1] to[6]on the remote control.
Select a band and frequency (step wand eon the previous page).Select a band. (step won the previous page)Select a band. (step won the previous page)The frequency blinks once, and the station is saved in the
memory.¡The 6 stations with good reception will be automatically saved in the memory
under preset numbers 1 
to6.
¡Once set, the preset stations are sequentially scanned for 5 seconds each.
¡To stop the scanning, touch or press numbers [1] to[6].
ENTER
TILT
OPENVOLUME
MUTE NAVI DISP
CQ-VD7700U
MODE
OPEN / CLOSE
DISC
POWERASPECTP
·MODE
NAVIGATION
SD CARDTRACK/
CHANNEL
ASP
IN-DASH 7 WIDESCREEN COLOR LCD MONITOR TV / DVD / SD RECEIVER
OPEN / CLOSE
CQ-VD7700U
TILT
ENTER
MODE
BandStereo indicator
Mode display
[MODE] []] [[] (Tuning)
[ENTER] (Band) Frequency
ENTER
PWR NAVI MODE MENU
CHAPTER
ASPECT
P-MODETRACK
NAVIGATION
STOP TOP MENU DVD / SD MENUST / MONOCH1 CH2
RANDOM RETURN
OSD
RET
RAND
AUDIOANGLE
REP
SUBSPACE MUTEVOL
GRP
DISP
12 3
45 6
7
A8
09
PA G E
SCAN PAUSE PLAY
SUBTITLE REPEAT
SCROLLTITLE / CHAPTERVOL
CAR AV
1
2
3
4
5
6MODE
[1] to [6]
(Preset memory)[]] [[] 
(Tuning)
[ENTER] 
(Band) [MODE] 
Radio ModeTouch .
.
Press [MODE]to change to radio mode.RemotePanelBandTouch             ,            ,            or            .
Press [ENTER]to change band.
Note:The stereo indicator lights during 
reception of an FM stereo broadcast.RemotePanel
12
TuningTouch TUNE : up
TUNE : down
[[]: up
[]]: down
Touch/press and hold [[]or[]]for more than 0.5 seconds,
then release. Seeking will start and stop at next available sta-
tion.RemotePanel
3
FM1
FM2
FM3
AM
Band Selection
When not in operation mode, Touch the center of touch panel [Area A]to show operation display. 
(apage 24) 
						

							4933E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
4832E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
ENTER
TILT
OPENVOLUME
MUTE NAVI DISP
CQ-VD7700U
MODE
OPEN / CLOSE
DISC
POWERASPECTP
·MODE
NAVIGATION
SD CARDTRACK/
CHANNEL
ASP
IN-DASH 7 WIDESCREEN COLOR LCD MONITOR TV / DVD / SD RECEIVER
OPEN / CLOSE
CQ-VD7700U
TILT
ENTER
MODE
ENTER
PWR NAVI MODE MENU
CHAPTER
ASPECT
P-MODETRACK
NAVIGATION
STOP TOP MENU DVD / SD MENUST / MONOCH1 CH2
RANDOM RETURN
OSD
RET
RAND
AUDIOANGLE
REP
SUBSPACE MUTEVOL
GRP
DISP
12 3
45 6
7
A8
09
PA G E
SCAN PAUSE PLAY
SUBTITLE REPEAT
SCROLLTITLE / CHAPTERVOL
CAR AV
MODE
RAND
REP
1
25[MODE]
[]] [[](TRACK)
[}] [{](DISC)
[RAND] (RANDOM)
[REP](REPEAT)
CD Changer Control
CD changer functions are designed for an optional
Panasonic CD changer unit.
Read the operating instructions for CD changer as well.
Preparation:Connect the CD changer (aInstallation
instructions), and load a magazine (disc).Caution:Please refer to page 87 for disc-related
matters.Notes: 
¡The power will be turned on automatically when a
magazine is loaded.
¡Load a magazine with CDs when “NO MAGAZINE” is
displayed.
¡CD text is not supported in CD changer mode.¡CD changer cannot play MP3 data recorded CD-
R/RW discs.CD Changer ModePress [MODE]to change to CD changer mode and
playback starts.System ExpansionThe use of Dual CD Changer Selector CA-CD55
(option) allows you to make the following connec-
tions. 
(a
Installation Instructions)
Dual changers connectionTwo changers can be connected to the terminals of
CA-CD55 respectively.
The changers are arranged as follows.
*/ [1]: CH 1
*/ [2]: CH 2
* Touch panel symbols will change to indicate these
current mode.
Mode display
Track number
Playing time
Total track number
Total time
Disc list
Operation buttons
Disc number
Play 
setting
Changer number
[MODE]
[]] [[](TRACK)
[}] [{](DISC)
[d](TRACK)
[s](TRACK)
[1](CH 1)
[2](CH 2)
[5](SCAN)
Track Selection
[d]
(TRACK)
[s]
(TRACK)
Next trackBeginning of the current track 
Previous track (Touch/Press twice.)
❑ Basic Operations
Operations
Panel
Remote
Disc Selection
[}](DISC)
[{](DISC):Next disc
Previous disc
Fast Forward/
Fast Reverse
[d]
[s]Touch/Press and hold.
Fast forward
Fast reverse
Release to resume playback.
Random Play
or
[RAND]
(RANDOM)
Touch/Press and hold for more than 2 sec-
onds.
Touch/Press and hold again to cancel. All TracksTouch/Press.
Touch/Press again to cancel.
All Tracks
on the
Current
Disc
Scan PlayThe first 10 seconds of each
track will be played.or
[5] (SCAN)
Touch/Press and hold for more than 2 sec-
onds.
Touch/Press and hold again to cancel. All TracksTouch/Press.
Touch/Press again to cancel.
1st Track
on Each
Disc
* *
Repeat Play
or
[REP]
(REPEAT)
Touch/Press and hold for more than 2 sec-
onds.
Touch/Press and hold again to cancel. Current
TrackTouch/Press.
Touch/Press again to cancel.
Current
Disc
*
Note: It is possible to press []] [[] on the display unit instead of [s] [d] on the remote control
. 
* Touch panel symbols will change to indicate these current mode.
When not in operation mode, Touch the center of touch panel [Area A]to show operation display. 
(apage 24) 
						

							35E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
5034E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
SD-Card PlayerIMPORTANT• If you have saved still image and/or moving image
data on SD Memory Cards by yourself using a PC, you
may not be able to play images unless you have con-
figured the folders correctly and named the folders
and files correctly. For further detail, refer to the next
page.
• When playing music using an SD card, play the SD
Audio files which were written on the card using SD-Jukebox (option).
• If you have saved data on SD cards using “Panasonic
SD Multi AV Device”, for instance, which is available
as an optional accessory, the data can be played by
the unit straight way.
• Use SD card with a memory size of 512 MB or less.Playable data formats on the SD-CardCQ-VD7700U/VD7500U can treat the following data for-
mats.
Still Pictures:JPEG files taken on digital
cameras conforming to DCF standards.
(set down by the Japan Electronics and
Information Technology Industries
Association.)
Motion pictures: MPEG4 files (ASF for-
mat) taken on a digital video camera or
SD Multi AV Device.
Notes:
• If the file list screen contains 7 or more
files, press [}], [{],
[]]
or[[] to
scroll to the next (or previous)
page.
• When MPEG4 moving pictures are
played back, mosaic-like patterns may occur or frames
may be dropped during scenes with fast-moving subjects.
This is normal and not a sign of trouble.
Music (Audio files): MP3 and AAC audio files recorded with
“Panasonic Media Manager” or “SD-Jukebox” software
included with Panasonic SD Multi AV Device and SD Audio
Player. Notes:
• SD audio files written using a function other than SD-
Jukebox may not be recognized.
• MP3 audio files cannot be played. (However, this does
not  apply to MP3 files that were written using SD-
Jukebox for use as SD audio files.)
• This unit can neither record nor erase the data.
• Titles and names of the artists may not always appear on
the display.
• If there are multiple numbers of still
pictures that are tied in with SD-
Jukebox, only the first still picture is
displayed.
• It may not be possible for the unit to
play back some kind of still pictures
even when they are tied in with SD-
Jukebox.
Voice: G.726 files recorded on a digital video camera or SD
Multi AV Device.
Notes:
• Some files are not compatible with this unit and can not be
played back. For example: Motion picture files recorded
using a digital still camera with motion picture function, IC
recorder voice files etc.
• Under certain condition, some files may not be played back
even if these are compatible ones.How to record play data on SD-Cards❒ Personal Computer• You can copy Still pictures and Motion pictures to your
SD-Card by connecting it to a computer with a USB SD-
Card Reader/Writer (BN-SDCAP, option) or PC card adapter
(BN-SDABP, option) When recording to an SD-Card on a
computer. (Please refer to the “IMPORTANT” statement
above.)• If you have attached still pictures to an audio file (using
SD-Jukebox Ver.3.0 or later, option) the unit can also show
the first of these pictures.
Treatments of SD-Card❒ Other equipment (example: Digital still camera, IC Voice Recorder, Digital Camcorder)The SD-Card recorded by some certain equipment (see previous page) can be played back on this unit without special
procedures. This equipment creates folders and files in the following way: 
DCIM
100CDPFP
PRL001SD_VIDEO
SD_VC100
SD_V
OICE
SD_A
UDIO
root
JPEG files
MPEG4 files
Voice files
Music files
• SD_VOICE and SD_AUDIO are hidden folders created when you record
voice or audio files, and play automatically on other equipment.
This unit needs these folders on an SD-Card to play the files. Do not delete
them on your computer.
• “DCIM”, “SD_VIDEO”, “SD_VOICE” and “SD_AUDIO” are necessary to play
files but have no effect on operation.
• You may be unable to play some files due to the origin of the copy, or the
naming of folders and files.❒ 
Naming rule for the recoding files on SD-Cards.
JPEG still pictures MPEG4 motion pictures
Example: Example:
IMGA  0001.JPG MOL 001.ASF
Four      Four numbers 3 digits hexadecimal numbers
characters (Numbers 0 to 9 and letters A
to F)
Make sure that none of the files in a folder have the same last 4 (or 3)
characters These files can not be played back.
SD logo is a trademark.
Portions of this product are protected under copyright law and are provided a license by
ARIS/SOLANA/4C. Licensed AAC Patents (U.S. patent under numbers);
08/937,950 5,394,473 5,579,430 5,481,614 5,299,238 5,581,654 5848391
5,583,962 08/678,666 5,592,584 5,299,239 05-183,988 5,291,557 5,274,740
98/03037 5,781,888 5,299,240 5,548,574 5,451,954 5,633,981 97/02875
08/039,478 5,197,087 08/506,729 5 400 433 5 297 236 97/02874 08/211,547 
5,490,170 08/576,495 5,222,189 4,914,701 98/03036 5,703,999 5,264,846 
5,264,846 5,717,821 5,357,594 5,235,671 5,227,788 08/557,046 5,268,685 
08/392,756 5 752 225 07/640,550 5,285,498 08/894,844 5,375,189
Cautions:
• Do not leave the SD-Card where they will be become
hot or exposed to direct sunlight or where electric-
magnetic waves or static electricity occurs readily.
• Keep the terminal area on the back of the cards free
from dirt, water and foreign matter. Do not touch this
area with your hands or any other objects.
• Static-Electricity or malfunctioning of the unit or the
cards may cause the cards to be damaged or their data
to be lost. It is recommended that valuable data be
stored on the PC as well.Note: 
Do not leave cards on the following places:
• Direct sunlight
• Near car heaters
• Dirty, dusty and damp areas
• Seats and dashboards
❑Notes on SD-Card
51 
						

							5337E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
5236E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
SD-Card Player
(continued)
ENTER
PWR NAVI MODE MENU
CHAPTER
ASPECTTRACKNAVIGATIONSTOP TOP MENU DVD / SD MENUST / MONOCH1 CH2RANDOM RETURN
OSD
RET
RAND
AUDIOANGLE
REP
SUB
VOLGRP
DISP
12 3
45 6
78 9
PA G E
SCAN PAUSE PLAYSUBTITLE REPEAT
SCROLLTITLE / CHAPTERVOL
Still pictures Movie Music Voice
JPEG(DCF Standard)
MPEG4
(ASF format)AAC G.726
❑Playable Data
❑Inserting the SD-Card
Insert and slide
the card until it
clicks into
place.
Cautions:
¡Do not place your face in front of the slot when inserting
and removing cards. The slot mechanism has a spring
so the card may eject with force.
¡Do not insert the SD-Card into the CD slot.
¡Do not insert foreign materials into the SD-Card slot.
❑SD Mode Selectionq
Select the SD.
:
: [MODE]
w
Select the data type.
: Not available
: [}] or[{]
a[ENTER]
Caution:To prevent the data damage to the SD-Card,
never eject the SD-Card while playing or turn the ACC off
while the unit is using the card.
e
Select the playing data.
: Not available
: [}], [{], []] or [[]
a[ENTER]
❑Go to SD Menu
:
: [SD] (TOP MENU)
❑Go to SD Setup Menu*
:
: [DVD/SD MENU](SETUP MENU)
❑Removing the SD-Card
Press on the center of the card to unlock, then pull
straight out.
Press on the center.            Pull straight out.
Caution: Do not keep the SD-Card in the slot at half-way
to prevent the front panel from hitting the card when the
front panel is opening or closing.
Note: Do not leave an SD-Card inserted inside the unit
when it is not used.RemotePanelRemotePanelRemote
RemotePanelRemotePanel
[3] (STOP)
[y](PAUSE)
[5](PLAY)
[s][d]
[SD] 
(TOP MENU)
[REP] 
(REPEAT)
REP
[]] [[]
[}] [{] 
[ENTER]
Notes:
¡Play may not be possible sometimes due to the condition of the data.
¡Operation is not guaranteed with Multi Media Card.
¡All functions of SD Card Player cannot be operable only on the
touch panel. Use buttons on the remote control and the main 
unit as well. You can play the following types of data recorded on
an SD-Card:
For details, (apage 50).
SD-Card slot
Beveled edge
Label side up
[DVD/SD MENU] 
(SETUP MENU)Panel
Note: In the SD mode, when the following operation is performed
and then the SD mode is restored, the 
“MODE SELECT” screen will
appear without failure.
¡Power off ¡ACC off ¡Mode Change
❑Operation of SD-Card
Operations
* While the file list screen is displayed.
Note: It is possible to press []] [[] on the display unit instead of [s] [d] on the remote control
. 
Fast Forward/
Fast Reverse
[d]
[s]Press and hold.
Fast forward
Fast reverse
Release to resume playback.
Play (Slideshow)
[5](PLAY)
[
}
][]]
[
{
][[]Playback starts.
The still pictures will be played back for 5 seconds each
(Slidshow). (While the still picture playback screen is displayed.)
REPEAT*
Current
FileSelect [1 FILE/MUSIC]in [REPEAT].
Select [OFF] in[REPEAT]to cancel.
ALL
FilesSelect [ALL]in [REPEAT].
Select [OFF]in[REPEAT]to cancel.
Note:To record data on SD-Cards, (apage 50).
LOCKJPEG
LOCKMPEG4
ASF
LOCKAAC
LOCKVOICE
LOCKMPEG4
ASF
LOCKAAC
LOCKVOICE
LOCKJPEG
LOCKMPEG4
ASF
LOCKAAC
LOCKVOICE
LOCKJPEG
LOCKMPEG4
ASF
LOCKAAC
LOCKVOICE
LOCKMPEG4
ASF
LOCKAAC
[DVD/SD
MENU] 
a
[}
][]]
[
{
][[]
SELECT PLAYLIST*
LOCKAAC
[DVD/SD
MENU] 
a
[}
][]]
[
{
][[]
DISPLAY ON/OFF*
SCREEN*
[DVD/SD
MENU] 
a
[}
][]]
[
{
][[]
LOCKJPEG
LOCKMPEG4
ASF
LOCKAAC
LOCKVOICELOCKMPEG4
ASF
[DVD/SD
MENU] 
a
[}
][]]
[
{
][[]
Remote
Go to Beginning
[d]
[s]Next file 
Beginning of the current file
Previous file (Press twice.)
File Selection
LOCKJPEG
LOCKMPEG4
ASF
LOCKAAC
LOCKVOICE
Select a file to play back.
Stop
[3]
(STOP)Press this to return to the file list screen.
LOCKJPEG
LOCKMPEG4
ASF
LOCKAAC
LOCKVOICE
Pause
[y]
(PAUSE)Press this to stop the playback temporarily.
DEFAULT
PLAYLIST
PLAYLISTx
ON
OFF 
FULL
NORMAL All music files recorded are played back. 
(default)
The selected playlist is played back.
(If the PLAYLIST is recorded on the SD-Card.)
The SD information display is set to ON. 
(default)
The SD information display is set to off.
Enlarged screen (default)
Normal screen
Indicates compatible data types.
LOCKJPEG
LOCKMPEG4
ASF
LOCKAAC
LOCKVOICE
ENTER
DISC
SD CARD
TRACK/
CHANNEL
ERODE
LOCK
ENTER
[]] [[]
[}] [{] 
(ENTER)
When not in operation mode, Touch the center of touch panel [Area A]to show operation display. 
(apage 24) 
						

							5539E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
5438E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
MENU: User Settings❏MENU Operation
: Previous menu
: Exit
ENTER
PWR NAVI MODE MENU
CHAPTER
ASPECT
P-MODETRACKNAVIGATIONSTOP TOP MENU DVD / SD MENUST / MONOCH1 CH2RANDOM RETURN
OSD
RET
RAND
AUDIOANGLEREP
SUBSPACE MUTEVOLGRP
DISP
12 3
45 6
7
A8
09
PAG E
SCAN PAUSE PLAYSUBTITLE REPEAT
SCROLLTITLE / CHAPTERVOL
CAR AVMODEMENU
ENTER
TILT
NAVI DISP
CQ-VD7700U
MODE
OPEN / CLOSE
DISC
POWER NAVIGATION
SD CARDTRACK/
CHANNEL
DASH 7 WIDESCREEN COLOR LCD MONITOR TV / DVD / SD RECEIVER
ASPECTP
·MODE
ASP
ENTER
MODE
[MODE]  [MENU]
[}][{][]][[]
(Select/adjust)
[ENTER]
[MODE]
[}][{][]][[]
(Select/adjust)
[ENTER]
¡Go to MENU
: Touch  .
: Press [MENU].
¡Operations
Touching a menu symbol:Item selection and adjust
: previous menu.
: Return to regular mode
[}], [{], []], [[]
a[ENTER] :Item selection and adjust
[MENU] :Previous menu
[MODE] :Return to regular mode
RemotePanelRemotePanel
Note: 
The display returns to the previous status if there is no operation for more than 60 seconds after changing to the setting menu.
DISPLAY UNIT(Monitor position)
¡Tilt angle adjustment
TILT
Notes: ¡For smooth adjustment, make sure
to first return the lateral angle to the
neutral position and then adjust the
tilt angle.¡The monitor position setting menu
can also be displayed by pressing
the [TILT]button on the display
unit for more than 2 seconds. 
(apage 35)
OPEN/CLOSE
default: MANUAL
AUTO:The monitor is opened
automatically when turning ON
ACC.
MANUAL:The monitor is not
opened automatically.
AUTO
MANUAL
or  
[]]or [[]a[ENTER]
Note:You can also enter this setting
menu by pressing and holding [TILT]
button.
Remote
AUTO
MANUALPanel
5
4
3
2
1
or 
[]]or [[]
* [1]to [5]keys are not available.
Remote
[
]
Panel
1
default: 5
5
Menu Setting Value Operations
: Previous menu
: Exit
BEEP(Beep or no beep during operating)GUIDANCE
Guidance appearance during
video mode operation.
: guidance appears
: no guidance
appears
default: ON
OFFON
or 
[]]or [[] a[ENTER]
Remote
ON
OFFPanel
CLOCK(Clock display)
DISPLAY
: 
clock display OFF
: 
clock display ON ([12:00] is dis-
played before adjusting the
clock.)
default: OFF
ONOFF
or 
[]]or [[]
a[ENTER]Remote
ON
OFFPanel
(Year adjustment)
(Month adjustment)
(Day adjustment)
(Hour adjustment)
(Minute adjustment)Notes: 
¡To starts the clock return to regular
mode by pressing [MODE] or
touching .
¡Perform the setup of Daylight
Saving Time manually.MINUTE ADJUSTHOUR ADJUSTDAY ADJUSTMONTH ADJUSTYEAR ADJUST
default:
YEAR ADJUST: 2004
MONTH ADJUST: 1
DAY ADJUST: 1
HOUR ADJUST: AM12
MINUTE ADJUST: 0
or 
[}
]or [
{
]a[]]or [[]
a[ENTER]
Remote
[
]Panel
default: ONON
OFF
[]]or [[]a[ENTER]
Remote
ON
OFF
Panel
Menu Setting Value Operations
Guidance display
Menu selection order (apage 245) 
						

							5741E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
5640E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
MENU: User Settings 
(continued)
: Previous menu
: Exit
CALENDAR(Calendar Display)Note:The calendar is not editable.
(e.g. Holidays cannot be marked.)
default: Same as Clock
default: Same as ClockYEARMONTH
MONTH: 
or 
YEAR: 
or 
MONTH: []]or [[]
YEAR:[
{
]or [
}
]
This function executes no setting, only
viewing.
Remote
}
{
[
]
Panel
TOUCH PANEL(Panel touch position adjustment)
Position difference between the touch-
ing position and the displaying symbol
position may appear in the following
situations:
1. The display position adjustment is
executed.
2. The system is initialized.
3. The power is turned off soon after
the touch panel is adjusted.
For the cases above, readjust the
touch panel position.
Note:This function can be performed
on the touch panel.
Menu Setting Value Operations
This function is used only when there are some differences between the
touching position and the symbol position displayed on the monitor.
This function is not used ordinarily.
qTouch the four corners of the touch panel counterclockwise.
wTouch  to finish this setup. Touch  to retry.
AGAIN
END
Touch forth
Touch firstTouch second Touch third
: Previous menu
: Exit
ID-CODE(ID Code Setting)Prior to operating this unit, it is advis-
able to assign a 4-digit ID code for
security. 
(Make sure to use four digitsfor ID
code.)
Once the ID code has been set, the unit
cannot be operated if the main power
supply is disconnected then re-con-
nected. It is electronically locked so
that a thief can not use the stolen unit
unless that person knows the code you
have set.
The ID code operation must be per-
formed only by the person to whom
the unit belongs.
Generally, it is not necessary to enter
the ID code each time when using the
unit if it has never been disconnected
from the main power supply (car bat-
tery).Note:The ID code setting cannot be
eliminated even by the memory clear
function.to 
4 digits numeric code
default: none
Caution:Record your regis-
tered ID code and keep it in a
secure location. If you forget it,
you will be unable to use the
unit. In case you forget the ID
code, please consult your near-
est Panasonic Servicenter.Note:The inputted code is not
displayed for your security.
9
0
to 
[0]to [9]
How to set your ID code (for the first time)q
Enter an 4 digit ID code.
wEnter the same 
4 digit 
ID code again.
How to change your ID code 
qEnter the preset (old) 4 digit 
ID code.
If the wrong ID code is entered, a new
ID code cannot be registered.
wEnter a new 
4 digit 
ID code.
eEnter the new 
4 digit 
ID code again.
How to cancel the known ID code 
Note:Should your unit ever require service,
cancel your ID code before sending for repair.qEnter the preset (old) 
4 digit 
ID code.
If the wrong ID code is entered, it is
not possible to cancel the ID code
function.
wPress and hold [ENTER]until
“Complete!
” is displayed
. The ID code
cancelling procedure is completed.
The unit now works without an ID
code.
Note:
Refer to ID Code Input regarding
how to enter the ID code. (apage 6)
Remote
9
0
Panel
Menu Setting Value Operations
MEMORY CLEARAll current memories are returned to
default settings.
Note:In the SD mode, SD MENU set-
tings are not returned to the default
setting even when YES is selected as
this setting. 
Caution:Be aware that this setting
restores the unit to default settings, so
that all the memories and settings that
you have set will be eliminated.:
no memory clear. The display
returns to the previous one.
:
default settings
default: NO
YESNO
: Memory clearance
: No Memory clearance
[[]a[ENTER] [[]a[ENTER]:
Memory clearance[]]
a[ENTER]:a
No Memory clearance
Remote
CANCELOK
YESPanel 
						

							5943E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
5842E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
MENU: Display (Screen) Settings
MENU: Capture Function
: Previous menu
: Exit
DIMMER
: automatically adjusted
according to ambient
light intensity.
default: AUTO
4
3
2
1AUTO
or 
[]]or [[]
Remote
[
]
Panel
PICTURE(Display Adjustment)
(Adjust the image contrast)
CONTRAST
: Decrease the contrast
between black and white
: Increase the contrast
between black and white
[]
or 
[}
]or [
{
]a[]]or [[]
Remote
[
]
Panel
(Adjust the image brightness)
BRIGHT
: Darken: Lighten
[]
(Adjust the image color depth)
COLOR
: Lighten the depth of color
on the display: Deepen the depth of color
on the display
[]
(Adjust the image tone or tint)
TINT
: Emphasize red in the
color image: Emphasize green in the
color image
[]
LCD DIMMER(SUB-LCD dimmer adjustment)
: Darker
: Brighter
default: HIGH
HIGHLOW
or 
[]]or [[] 
a[ENTER]
Remote
HIGH
LOWPanel
LCD CONTRAST(SUB-LCD contrast adjustment)Decrease Increase
default: 4
5
4
3
2
1
or 
[]]or [[]
Remote
[
]Panel
Menu Setting Value Operations
Darker
Brighter
: Previous menu
: Exit
CAPTURE(Image Capture)Up to five images can be imported
from TV, VTR, DVD or Video CD (VCD).Preparation:
Show the image  that
you would like to capture on the dis-
play.
Note: Refer to “Display mode
changes” page to display the imported
image on the screen. (apage 26)
Copyright
It is prohibited by copyright laws to
copy, distribute and deliver copyright-
ed materials such as commercial
DVDs/Video CDs or other published or
broadcast material without the
approval of copyright holder except for
personal use.Note: A captured image may have
some distortion or be otherwise differ-
ent from the original image due to
compression.
to 
¡You can store maximum five
images.
¡The existing image is replaced
with a new image when sav-
ing it. Check the right-hand
smaller image on the screen
before saving a new one. If
you would like to keep the
existing image, do not over-
write.
Notes:
¡Do not turn off the unit while
saving an image.
¡To capture an image from TV,
the broadcasting condition
should be fairly good.
IMAGE5
IMAGE1Select Save area
a,
......
or 
a
[ENTER] a[]]or [[] 
a [ENTER] a[]]or [[]
Remote
YES
IMAGE5
IMAGE2
IMAGE1
ENTERPanel
Menu Setting Value Operations
w
q q
w
Direct Image Capture 
(Only for remote control)
If you would like to capture a picture, press and hold [OSD](CAPTURE)
for more than 2 seconds.
Subsequent steps are the same as the steps wdescribed above.
ENTER
PWR NAVI MODE MENU
CHAPTER
ASPECT
P-MODETRACKNAVIGATIONSTOP TOP MENU DVD / SD MENUST / MONOCH1 CH2RANDOM RETURN
OSD
RET
RAND
AUDIOANGLE
REP
SUBSPACE MUTEVOL
GRP
DISP
12 3
45 6
7
A8
09
PA G E
SCAN PAUSE PLAYSUBTITLE REPEAT
SCROLLTITLE / CHAPTERVOL
CAR AVMODE
MENUOSD
[OSD] (CAPTURE)
[MODE] (End)
[MENU] 
						

							6145E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
6044E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
MENU: Capture Function 
(continued)
MENU: Audio Settings (for VD7700U)
: Previous menu
: Exit
INITIALIZEYou can restore the default image
and delete your captured image.
to 
IMAGE5
IMAGE1
Select area
, ......
or
a
: Restore the image.
(delete your image)
: Restore no image.
[]]or [[] a[ENTER] a
[[]: Restore the image.
(delete your image)
[]]: Restore no image.
a[ENTER]
RemoteNOYES
IMAGE5
IMAGE2
IMAGE1
Panel
Menu Setting Value Operations
MENU: Animation Settings
: Previous menu
: Exit
ANIMATION(Change the animation)Note:This function is available only in
non-video mode.Animation patterns
Default: A
C
B
A
Touch or or 
[]]or [[] a[ENTER]Remote
C
B
A
Panel
COLOR(Change the animation color)Note:This function is available only in
non-video mode (CD, MP3, Radio, CD
Changer).Animation colors
to  
Default: A
H
A
Touch , ........ or 
[}]or [{] a[]]or [[] a
[ENTER]Remote
H
B
A
Panel
Menu Setting Value Operations
Touch to select
: Previous menu
: Exit
PARAMETRIC–EQ(Adjusting the Level for Each of the
Frequency Bands: EQ=Equalizer)(Select the method of setting)
MODE
: Same settings are
used for all speak-
ers
: Each speaker can
be set.
Default: ALL
Professional
ALL
or 
[]]or [[] a[ENTER]
Remote
Professional
ALLPanel
(Select the speaker to adjust)
(For
)
ProfessionalSPEAKER
, , 
Default: FRONT
SUR
CENTER
FRONT
or 
[}]or [{] a[]]or [[]
Remote
[
]Panel
(Select a frequency band of the preset
equalizer to adjust)
BAND
: 
40/63/80/100/160 Hz
: 
315/500/630/800/1.25k Hz
: 
2.5k/4k/5k/6.3k/10k Hz
Default: LOW
HIGHMIDLOW
(Select the center frequency of the set-
ting band)
FREQ
40/63/80/100/160 Hz (LOW)315/500/630/800/1.25k Hz (MID)2.5k/4k/5k/6.3k/10k (HIGH)
Default: 40 Hz
(Adjust the gain in each frequency)
GAIN
–12 to +12 dB (by 2 dB step)
Default: 
±0 dB
(Select a width of the frequency band
to adjust the gain)
Note:These equalizer settings are not
applied to the sub-woofer.
WIDTH
1 to 4
Default: 4
(continued on next page a)
Menu Setting Value Operations
The level of each of the 15 frequency bands can be adjusted,
and up to 6 different levels can be stored in the memory.
Wait for a while when “LOADING >>>” appears on the dis-
play. 
						

							6347E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
6246E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
MENU: 
Audio Settings (for VD7700U)
(continued): Previous menu
: Exit
PARAMETRIC–EQ(continued)
(Recall or preset the equalizer setting)
Note:These equalizer settings are not
applied to the sub-woofer.
PRESET
:
1 to 3 (Preset number), 7(FLAT)
:
4 to 6 (Preset number), 7(FLAT)
Note:When selecting  “7
(FLAT)”, the preset level is set to
0 dB.
¡The new level adjustment
will overwrite the previous
level adjustment, erasing it
in the process.ProfessionalALL
to 
[}]or [{] a[]]or [[]
or
[1],[2],[3]....... [7]
To store a level adjustment in the
memory (preset memory)qMake adjustments before memorizing.
wTouch and hold preset button  to
for more than 2 seconds.
qMake adjustments before memorizing.
wPress and hold preset button [1]to [6]
for more than 2 seconds.Remote
6
1
PanelRemote
7 FLAT
1Panel
PRO LOGIC II(5.1 channel listening in Dolby surround
sound)
(Select a sound type)
MODE
, , , 
default : OFF
Notes:“PANORAMA”, “DIMEN-
SION” and ”CENTER WIDTH”
are adjustable when “MODE” is
set to “MUSIC”.
MATRIX
MUSIC
MOVIE
OFF
or or or 
[}]or [{] a[]]or [[] a
[ENTER]Remote
MATRIX
MUSIC
MOVIE
OFFPanel
Get large the sound space in the
“MUSIC” mode.
PANORAMA
, 
default : OFF
ON
OFF
or 
[}]or [{] a[]]or [[] a
[ENTER]Remote
ON
OFFPanel
(Adjust the dimension of the sound in
“MUSIC” mode)
DIMENSION
–3 to +3
default : ±0
(Widen the sound field of the center
speaker in “MUSIC” mode)
CENTER WIDTH
0 to 7
default : 0: UP
: Down
[}]or [{] a[]]or [[]
Remote][Panel
Menu Setting Value Operations
: Previous menu
: Exit
DOWN MIX(Changing Dolby digital/dts Audio to 2-
Channel Stereo Playback)
Note:This function is available only
when “Dolby digital” or “dts” source is
playing.: Original Source Output
: 2-channel conversion
output
default : OFF
ONOFF
or 
[]]or [[] a[ENTER]Remote
ON
OFFPanel
DR COMP(Dynamic Range Compression)
(Maintaining the ambience even while
listening at a low volume level)Compression style selecting 
(apage 73)
OFF : DR COMP OFF
STD: DR COMP ON
MIN: Made with the greatest
compression, roughly
equivalent to a TV broad-
cast.
default : OFF
or or 
[]]or [[] a[ENTER]Remote
MIN
STD
OFFPanel
SP SETUP(Speaker Setup)
(Setting the absence/presence and size
of each speaker)
(Front speaker setting)
FRONT
: 
for large speakers, when bass
playback is possible (at least
100 Hz or lower)
: 
for small speakers, or when
bass playback is not possible
default: LARGE
SMALLLARGE
a
or 
[}
]or [
{
]a[]]or [[]
a[ENTER]
Remote
LARGE
SMALL
FRONTPanel
(Center speaker setting)A center speaker (option, EAB-CF2 rec-
ommended) is required.
CENTER
: 
for large speakers, when bass
playback is possible (at least
100 Hz or lower)
: 
for small speakers, or when
bass playback is not possible
: 
when not using a center speaker
default: SMALL
NONESMALLLARGE
a
or or 
[}
]or [
{
]a[]]or [[]
a[ENTER]
(continued on next page a)
RemoteLARGE
SMALL
NONE
CENTERPanel
Menu Setting Value Operations
Note:Effective for 2-channel audio (LPCM, PPCM, Dolby Digital/dts 2-channel) and analog audio (TV, VTR, radio, CD
changer). 
						

							6549E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
6448E
N
G
L
I
S
H
CQ-VD7700U/VD7500U
MENU: 
Audio Settings (for VD7700U)
(continued): Previous menu
: Exit
SP SETUP(continued)
(Surround speaker setting)
SURROUND
:
for large speakers, when bass
playback is possible (at least
100 Hz or lower)
: 
for small speakers, or when
bass playback is not possible
: 
when not using surround
speakers
default: LARGE
NONESMALLLARGE
a
or 
or 
[}
]or [
{
]a[]]or [[]
a[ENTER]
RemoteLARGE
SMALL
NONE
SURROUNDPanel
(Subwoofer speaker setting)A subwoofer (option, CJ-SW38 recom-
mended) is required. A power amplifier
(option) is also required for connecting
a subwoofer.
SUB • W
: 
when using a subwoofer
: 
when not using a subwoofer
default: NO
NOYES
a
or 
[}
]or [
{
]a[]]or [[]
a[ENTER]
Remote
YES
NO
SUB • WPanel
SP LEVEL(Speaker Level)
(Adjusting the output balance of each
speaker)
(Left front speaker output balance)
(Center speaker output balance)
(Right front speaker output balance)
(Right surround speaker output bal-
ance)
(Left surround speaker output balance)
(Subwoofer speaker output balance)
SUB
¡W
L¡SURROUND
R¡SURROUNDFRONT RCENTERFRONT L
Setting range: –12 dB to +12 dB
(1 dB steps)
Default: ± 0 dB for all speakersA test signal (a continuous tone) is
output from each speaker for
approximately two seconds. 
Adjust the output balance so that
the tone appears to have the same
volume from each speaker.
Adjusting the output balance: 
Adjust the volume of all of the other
speakers to the volume level of the
speaker from which the test signal
appears to be the quietest.
¡If the speaker setting is “NONE” or
“NO” for a speaker, the test signal
is not output and that speaker
cannot be selected.  (apage 63)
¡Turn [VOLUME]or press [}]or
[{] (VOLUME)to adjust the vol-
ume of the test signal.
qTouch the image of the speaker you
want to set.
w: UP
: Down
q[}]or [{]
w[[]: UP
[]]: DownRemote
][Panel
Menu Setting Value Operations
Touch to select
: Previous menu
: Exit
SP DELAY(Speaker Delay)
(Adjusting the timing with which the
audio from each speaker reaches the
listener’s position)
(Center speaker delay time setting)
(Surround speaker delay time setting)¡Make this adjustment while listening
to sound.
¡If the speaker setting is “NONE” for a
speaker, that speaker cannot be
selected. 
(apage 63)
SURROUNDCENTER
Setting range: 
Center speaker...
0 ms to 5 ms (1 ms steps)
Surround speakers...
0 ms to 15 ms (1 ms steps)
1 ms = 0.001 seconds
Default: 0 ms for all speakers
qTouch a speaker image. (Center or
Surround)
w: Long
: Short
q[}]or [{]
w[[]: Long
[]]: ShortRemote
][Panel
VTR LEVEL(Setting the VTR (VTR1/VTR2) input
Level)Make this setting if it is not possible to
adjust the volume through the con-
nected device (on the output side). 
Note:This setting is adjustable for an
external device that is connected to
VTR1 or VTR2. (e.g. VCR): Input level
default: ±0 dB
Notes: 
¡If the input level from
VTR1/VTR2 is too high, the
audio will not be output nor-
mally.  Adjust the input level
so that “OVER” does not
appear.
¡After setting the input level
The volume can be adjusted
by turning the volume knob or
pressing [}]or [{](VOL-
UME)on the remote control.
+6
dB
+4 dB
+2 dB
±
0 dB
–2 dB
–4 dB
–6 dB
: Lower
: Higher
[]]: Lower
[[]: Higher
Remote
[]
Panel
Menu Setting Value Operations
Lower        Higher