Panasonic Lcd Monitor Dvd Receiver Cq Vd6505u Operating Instructions

							30
31CQ-VD6505U
English
❏MENU Operation
Note:
¡
The display returns to the previous status if there is no operation for more than 60 seconds after changing to the
setting menu.(Example: DVD mode)
Touch  in Operation Screen.
Touch desired setting.
qw
(Example: setting screen of “DISPLAY UNIT” apage 32)
Determines the setting and goes back to the pre-
vious menu out of the menu.e
Determines the setting and gets out of the menu.
[SRC] 
(Exit from the menu)
[MENU]
(Shows the menu display/
Goes back to the previous menu)
ASPECT
MUTE MENUNAVI
TUNE
FOLDERALBUM
TRACK
SRC
VOL
ASP
P-MODE
PWR
TILT
CQ-VD6505U
MENU
SRC[}] [{] 
						

							31
32CQ-VD6505U
English
ID-CODE
ID Code Setting
Prior to operating this unit, it is advisable to assign a 4-
digit ID code for security. Once the ID code has been set,
the unit cannot be operated if the main power supply is
disconnected then re-connected. It is electronically locked
so that a thief cannot use the stolen unit unless that per-
son knows the code you have set.
The ID code operation must be performed only by the
person to whom the unit belongs.
Generally, it is not necessary to enter the ID code each
time when using the unit if it has not been disconnected
from the main power supply (car battery).
to  4 digits numeric code
default: none
How to set your ID code (for the first time)
qEnter a 4 digit ID code.
wEnter the same 4 digit ID code again.
How to change your ID code 
qEnter the preset (old) 4 digit ID code. If the wrong ID
code is entered, a new ID code cannot be registered.
wEnter a new 4 digit ID code.
eEnter the new 4 digit ID code again.
How to cancel the known ID code 
qEnter the preset (old) 4 digit ID code. If the wrong ID
code is entered, it is not possible to cancel the ID code
function.
wTouch and hold  until “COMPLETED!” is dis-
played. The ID code cancelling procedure is completed.
The unit now works without an ID code.
Note: 
¡
Should your unit ever require service, cancel your ID
code before sending for repair.
¡The ID code setting cannot be eliminated even by the
memory clear function.
¡The inputted code is not displayed for your security.
90
Caution
¡Record your registered ID code and keep it in a
secure location. (Fill in the ID code memo (a
page 46).) If you forget it, you will be unable to
use the unit. In case you forget the ID code,
please consult your nearest Panasonic
Servicenter.
Settings (continued)
DISPLAY UNIT
Display adjustment
(Tilt angle adjustment)TILT
654321
default: 1
RADIOINPUT/OUTPUTDVDAUDIOSCREENUSER
CLOCK
Clock setting
: clock display ON (“12:00” is displayed
before adjusting the clock.)
: clock display OFF
default: 
: puts back hour.
: puts forward hour.
: puts back minute.
: puts forward minute.
Note: 
¡To start the clock, touch/press 
/[SRC]
.
¡Set the Daylight Saving Time manually.
default: HOUR ADJUST: 12
MINUTE ADJUST: 0
[
]
(Minute adjustment)MINUTE ADJUST
[
]
(Hour adjustment)HOUR ADJUST
OFF
OFF
ON
(Clock display)DISPLAY 
						

							32
33CQ-VD6505U
English
MEMORY CLEAR
Memory clearance
The state of all of the current memories are returned to
default settings.
Note: 
¡The ID code is not deleted by executing memory clear.
: clears the memory to default settings
: no memory clear. 
The display returns to the previous one.
appears when
is selected.
: proceed.
: no memory clear.
CANCEL
OK
YES
REALLY?
NO
YES
OTHER
Other settings
: operation sound (beep) ON
: operation sound (beep) OFF
default: 
ON
OFF
ON
(Beep setting)BEEP
: sets to ON if your car has ACC position.
: sets to OFF if your car has no ACC posi-
tion.
default: 
Note: 
¡For an ACC-equipped car, select ON.  The following
functions are available.
¡The power is turned on automatically when inserting
a disc or magazine.
¡selection disables turning on the power of the
main unit through the remote control.
: main unit-specific remote control
: rear monitor (option)-specific remote
control
default: 
: LED indicator not blinking with ignition
key being at out-of-ACC
: LED indicator blinking with ignition key
being at out-of-ACC
default: 
: displays the menu in English.
: displays the menu in French.
default: 
ENGLISH
FRENCH
ENGLISH
(Language setting)MENU DISPLAY
ON
ON
OFF
(Security LED setting)SECURITY LED
FRONT
REAR
FRONT
(Remote control setting)REMOTE CONTROL
OFF
ON
OFF
ON
(Setting ACC selection ON and
OFF)ACC SELECT
Caution
¡Be aware that this setting restores the unit to default
settings, so that all the memories and settings that
you have set will be eliminated.
OFF
ACC
IGN
Caution
¡Be sure to select OFF when your car has no ACC
position in the ignition switch. Failure to do this
could cause the battery to go dead. 
						

							33
34CQ-VD6505U
English
Settings (continued)
RADIOINPUT/OUTPUTDVDAUDIOSCREENUSER
DIMMER
Adjusting the brightness
: automatically adjusted according to
ambient light intensity.
default: AUTO
4321
AUTO
PICTURE
Display appearance
: decreases the contrast between black and white.
: increases the contrast between black and white.
[
]
(Adjust the image contrast)CONTRAST
: darkens.
: lightens.
[
]
(Adjust the image brightness)BRIGHT
: lightens the depth of color on the display.
: deepens the depth of color on the display.
[
]
(Adjust the image color depth)COLOR
: emphasizes red in the color image.
: emphasizes green in the color image.
[
]
(Adjust the image tone or tint)TINT
RADIOINPUT/OUTPUTDVDAUDIOSCREENUSER
Darker
Brighter
GRAPHIC-EQ (Graphic-equalizer)
Graphic-equalizer
Six EQ presets are already provided at shipment in this
unit. To
recall a preset memory, select the correspon-
ding preset buttons 
[1]to [6].
: (Flat) flat frequency response
: (Rock) speedy and heavy sound
: (Pop) wide-ranged and deep sound
: (Vocal) clear sound
: (Jazz) jazz-specific deep sound
: (Club) club and disco-specific sound
You may set your own EQ or modify factory preset-
tings in each memory button by following the instruc-
tions below:
Adjusting level of each preset
The level of each of the 7 frequency bands can be
adjusted.
qSelect the preset number that you prefer to adjust.
wTouch/press 
/[
{][
}]to adjust each fre-
quency.
eTouch/press the same preset number for more than
2 seconds.
Frequency band
(Hz)
Adjustment range: –12 dB to +12 dB (in 2 dB steps)
default: ±0 dB for each band
Note: 
¡The new level adjustment will overwrite the previous
level adjustment.
¡For resuming the factory settings, touch and hold
(INIT (initialize)) 
for more than 2 seconds.
16 k6k3k1k40016060
6
5
4
3
2
1
(Display)
SOUND SETUP
Sound Set Up
: no GEQ or CS Auto setting
: goes to GEQ setting
: goes to CS Auto setting
default: 
THROUGH
CS Auto
GEQ
THROUGH
(Sound effect setting)SOUND EFFECT 
						

							¡To set the level to flat, touch and hold  (flat)
for more than 2 seconds.
¡Expectable effects vary with the audio format to be
used, settings in the menu, and other factors.
34
35CQ-VD6505U
English
: more
: less
: more
: less
: more
: less
Setting range: off, +1 to +10
default: off
]
[
(Applies to the Sub-woofer)SUB-W TruBass
]
[
(Applies to the rear speakers)REAR TruBass
]
[
(Applies to the front speakers)FRONT TruBass
(TruBass Setting)TruBass
: more
: less
: more
: less
Setting range: off, +1 to +10
default: +5
]
[
(Adjusts the SRS effect (center)
on rear speakers)CENTER TO REAR Mixing
]
[
(Adjusts the SRS effect (front)
on rear speakers)FRONT TO REAR Mixing
(Adjusts the SRS effect)Mixing
CS Auto 
CS Auto Setting
: more
: less
: more
: less
: more
: less
Setting range: off, +1 to +10
default: off
]
[
(Raises the central sound image)CENTER FOCUS
]
[
(Raises the rear sound image)REAR FOCUS
]
[
(Raises the front sound image)FRONT FOCUS
(Raises the sound image)FOCUS
(Customizing the setting)SELECT
Note: 
¡
TruBass®
TruBass is an audio technology to which the technique of
bass sound reproduction used in pipe organs is electri-
cally applied, and in which an equalizer is not used at all
and bass sound from the speakers to be used is richly
reproduced.
Note: 
¡
FOCUS®
Focus is an audio technology that moves the sound
image of playing sound vertically to reproduce the
sounds of instruments and voices clearly. 
						

							35
36CQ-VD6505U
English
Settings (continued)
SP LEVEL (Speaker level)
Adjusting the output balance of each speaker
: down,    : up
: down,    : up
: down,    : up
: down,    : up
: down,    : up
: down,    : up
Setting range: –10 dB to +10 dB (1 dB steps)
default: ±0 dB for all speakers
¡If the speaker setting is  or  for a speaker, the
test signal is not output and that speaker cannot be
selected. 
¡
Press [+]
or [–]
(VOL)to adjust the volume of the test
signal.
NONONE
[]
(Subwoofer speaker output
balance)SUB - W
[]
(Left surround speaker output
balance)L¡SUR
[]
(Right surround speaker out-
put balance)R¡SUR
[]
(Right front speaker output
balance)FRONT R
[]
(Center speaker output bal-
ance)CENTER
[]
(Left front speaker output bal-
ance)FRONT L
SP SETUP (Speaker set up)
Setting the absence/presence and size of each speaker
: for small speakers, or when bass playback
is not possible
: for large speakers, when bass playback is
possible (at least 100 Hz or lower)
default: LARGE
LARGE
SMALL
(Front speaker setting)FRONT
: subwoofer phase 0 degree
: subwoofer phase 180-degree inverted
Note: 
¡
This setting is feasible only when  is set to
.
default: 
0°
YES
SUB-W
180°
0°
(Phase setting)PHASE
: when using a subwoofer
: when not using a subwoofer
default: 
* A subwoofer (option, CJ-SW3003 recommended) is
required. A power amplifier (option) is also required for
connecting a subwoofer.
NO
NO
YES
(Subwoofer speaker setting)SUB - W
: when not using a center speaker
: for small speakers, or when bass playback
is not possible
: for large speakers, when bass playback is
possible (at least 100 Hz or lower)
default: 
* A center speaker (option, EAB-CF2 recommended) is
required.
NONE
LARGE
SMALL
NONE
(Center speaker setting)CENTER
: when not using a surround speaker
: for small speakers, or when bass playback
is not possible
: for large speakers, when bass playback is
possible (at least 100 Hz or lower)
default: LARGE
LARGE
SMALL
NONE
(Surround speaker setting)SUR
(AUDIO continued)
Note: 
¡While the private mode is active, only
can be
adjusted.FRONT 
						

							36
37CQ-VD6505U
English
: enables the test tone.
: disables the test tone.
default: 
¡When the test tone is set to on,  test signal (a continu-
ous tone) is output from each speaker for approximately
2 seconds. 
Adjust the output balance so that the tone appears to
have the same volume from each speaker.
Adjusting the output balance: 
Adjust the volume of all of the other speakers to the vol-
ume level of the speaker from which the test signal
appears to be the quietest.
OFF
OFF
ON
(Test tone output)TEST TONE
Note: 
¡While the private
mode is active, only
and
can be
adjusted.
FRONT R
FRONT L
CROSS OVER 
Cut off frequency
: down,    : up
Setting range: 63 Hz to 200 Hz 
default: 125 Hz
: down,    : up
Setting range: off, 63 Hz to 200 Hz  
default: off
Note: 
¡This setting is not available if 
is set to  .
¡is enabled only on the front speakers
(R/L) and rear speakers (L/R).HPF CUT OFF
ONCS Auto
[]
(High Pass Filter)HPF CUT OFF
[]
(Sub-woofer Low Pass Filter)LPF CUT OFF
TIME ALIGNMENT
(Delay time setting of each speaker)
Adjusting the timing with which the audio from each
speaker reaches the listener’s position
: down,    : up
Setting range: 0 ms to 5 ms (1 ms steps)
1 ms = 0.001 seconds
default: 0 ms
: down,    : up
Setting range: 0 ms to 15 ms (1 ms steps)
1 ms = 0.001 seconds
default: 0 ms
¡Make this adjustment while listening to sound.
¡If the speaker setting is  for a speaker, that
speaker cannot be selected.
¡
When “PRO LOGIC” is displayed, 15 ms are automatically
added to the delay time setting for the surround speakers.
NONE
[]
(Surround speaker delay time
setting)SUR
[]
(Center speaker delay time set-
ting)CENTER
SOURCE LEVEL
Setting the AV1/AV2 input level
Make this setting if it is not possible to adjust the volume
through the connected device (on the output side). 
: sets the level low/sound volume increases.
: sets the level high/sound volume decreases.
default: 
: sets the level low/sound volume increases.
: sets the level high/sound volume decreases.
Note: 
¡If the input level from AV1/AV2 is too high, the audio
will not be output normally.
¡After setting the input level
The volume can be adjusted by pressing [+]
or [–]
(VOL)on the remote control.
default: HIGH
HIGH
LOW
(Setting for AV2)AV2 LEVEL
HIGH
HIGH
LOW
(Setting for AV1)AV1 LEVEL 
						

							37
38CQ-VD6505U
English
Settings (continued)
DISPLAY
Display aspect and DVD software mode
: plays a video in 4:3 screen.
: plays a video in wide screen (16:9).
default: 
WIDE
WIDE
NARROW
(Display aspect setting)DVD ASPECT
: plays wide-screen video in Pan & Scan
mode (in which the left and right edges
of the screen are cut off).
: plays wide-screen video in letterbox
mode (in which black bands appear at
the top and bottom of the screen).
default: 
Note: 
¡
Set the software setting according to the symbol used
on jacket. (
apage 18)
¡DVD software mode setting is ignored if 
or  is already set in the software.
¡
Screen aspect of the display unit is changed according
to the aspect ratio setting (
apage 40) and DVD soft-
ware’s aspect.
: sets NTSC in accordance with the
equipment connected to AV OUT.  
: sets PAL in accordance with the equip-
ment connected to AV OUT.
default: 
The angle mark is displayed to indicate the parts where
multi-angle data is recorded.
: activates angle mark.
: inactivates angle mark.
default: 
ON
OFF
ON
(Angle mark setting)ANGLE MARK
NTSC
PAL
NTSC
(AV OUT terminal setting)TV TYPE
LETTER BOX
PAN & SCAN
PAN & SCAN
LETTER BOX
PAN & SCAN
(DVD software mode)LETTER BOX
LANGUAGE
Language Setting
: English
: French
: Spanish
: other language. Input the language code.
(apage 49)
default: ENG
OTHER
SPA
FRA
ENG
(DVD menu language)MENU
Note:
¡A disc supporting closed captioning and subtitles may
overlap each other on the screen. In this case, turn the
subtitle off.
: English
: French
: Spanish
: other language. Input the language code.
(apage 49)
default: ENG
OTHER
SPA
FRA
ENG
(Subtitle language)SUBTITLE
Note:
¡These adjustments being executed, playback will start
from the beginning of a disc.
: English
: French
: Spanish
: other language. Input the language code.
(apage 49)
default: ENG
OTHER
SPA
FRA
ENG
(Audio language)AUDIO
RADIOINPUT/OUTPUTDVDAUDIOSCREENUSER 
						

							38
39CQ-VD6505U
English
NAVI SETUP (Navigation set up)
(aSystem Upgrade Guidebook)
CAMERA SETUP
(aSystem Upgrade Guidebook)
SOURCE SKIP
Source skip
If AV1 is not used, the AV1 mode is skipped when chang-
ing the mode.
: skips AV1
: does not skip
default: 
If AV2 is not used, the AV2 mode is skipped when chang-
ing the mode.
: skips AV2
: does not skip
default: 
Note: 
¡When external devices are connected to this unit with-
out involving the Expansion Module (CY-EM100U,
option),  is not enabled because the con-
nected external devices are identified as AV2.
INPUT SELECT
(aSystem Upgrade Guidebook)
OUTPUT SELECT
(aSystem Upgrade Guidebook)
H-F SETUP
(aSystem Upgrade Guidebook)
AV2  SKIP
OFF
OFF
ON
(AV2  skip)AV2  SKIP
OFF
OFF
ON
(AV1  skip)AV1  SKIP
RADIOINPUT/OUTPUTDVDAUDIOSCREENUSER
DVD SOUND 
DVD sound setting
: activates Pro Logic.
: inactivates Pro Logic.
default: 
Note
: 
¡This setting is enabled only in the DVD/VCD/CD player
mode.
¡selection in some audio settings may disable
audio output from the subwoofer.
: simple stereo down mix
(Lo = Left only, Ro = Right only)
: surround element decodable down mix
(Lt = Left total, Rt = Right total)
Note
: 
¡This function is available only when “Dolby Digital” or
“dts” source is playing and when sound comes out
only from the front speakers adjusted with  .
default: 
Maintaining the ambience even while listening at a low
volume level
Compression style selecting 
: DR COMP ON
: made with the greatest compression,
roughly equivalent to a TV broadcast.
: DR COMP OFF
default: 
OFF
OFF
MIN
STD
(Dynamic Range Compression)DR COMP
Lt/Rt
SP SETUP
Lt/Rt
Lo/Ro
(To use the down mix function,
specify the type.)DOWN MIX
ON
OFF
OFF
ON
(5.1 channel listening in Dolby
surround sound)PRO LOGIC
MULTI-CH (Multiple channel)
Sound output of Dolby Digital 2 ch. from all speakers
: changes sound from 2 ch. to 5.1 ch.
: keeps the source output 2 ch. sound.
default: OFF
OFF
ON 
						

							39
40CQ-VD6505U
English
Settings (continued)
FM SETUP
Setting for FM stations
: adjusted automatically
: narrows the frequency bandwidth to be
received to prioritize noise reduction.
: widens the frequency bandwidth to be
received to prioritize sound quality.
default: 
: saves the preset stations in each band.
: saves the preset stations in all FM lists
regardless of band.
default: 
EACH
ALL
EACH
(Auto preset setting)AUTO PRESET
AUTO
WIDE
NARROW
AUTO
(FM IF filter switching) NOISE SUPPRESSION
AM SETUP
Setting for AM stations
: narrows the frequency bandwidth to be
received to prioritize noise reduction.
: goes between  and  .
: widens the frequency bandwidth to be
received to prioritize sound quality.
default: 
XM SETUP
(aSystem Upgrade Guidebook)
SIRIUS SETUP
(aSystem Upgrade Guidebook)
MID
WIDE
WIDENARROWMID
NARROW
(Noise suppression)NOISE SUPPRESSION
RADIOINPUT/OUTPUTDVDAUDIOSCREENUSER
❑Aspect Ratio
Default: NORMAL
Mode: 4 types
Press and hold [ASP]on the main unit to change the
aspect ratio as follows.
¡The conventional display
image has a 4 to 3 ratio of
horizontal to vertical.
¡In this case, a blank area
remains on the right and left
sides of the display. NORMAL
¡The screen is extended hori-
zontally as a whole to the
aspect ratio of 16 to 9.
¡The extension ratio is the
same at any point of the
screen. FULL
¡The screen is fully extended at
the normal aspect ratio of 4 to
3.
¡The top and bottom of the
screen are slightly cut. ZOOM
¡The screen is extended hori-
zontally to the aspect ratio of
16 to 9.
¡The extension ratio increases
toward the right and left ends
of the screen. JUST
ASPECTMUTE MENUNAVI
TUNE
FOLDERALBUM
TRACK
SRC
VOL
ASPP-MODE
PWR
TILTCQ-VD6505U
ASP
[ASP]
Other Settings