Panasonic Kx Tga510 Installation Manual

							– 1 –
 
For assistance, please call: 1-800-211-PANA(7262) 
5.8GHz Expandable Cordless Handset
Model No.  
KX-TGA510M 
Installation Manual 
PLEASE READ BEFORE USE AND SAVE. 
This handset is an accessory cordless handset, for use with Panasonic base units 
KX-TG5100/KX-TG5110. This installation manual only describes the steps necessary to start 
up the handset. Please read the KX-TG5100/KX-TG5110 operating instructions for further 
details. 
Installation 
Connecting the Charger unit 
• USE ONLY WITH Panasonic AC ADAPTOR KX-TCA1 (Order No. KX-TCA1-G).
• The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel 
warm during use.) 
Installing the battery 
Insert the battery ( ), and press it down until it snaps into the compartment ( ).
 
When finished, close the cover.
 
PQQX13604YA 
  S0203-1033 
Accessories  
(included)  For extra orders, call 1-800-332-5368. 
 Charger Unit  . . . . . . . . . . . . . . . . . . . . .one
Charger Order No. PQLV30019ZM 
AC Adaptor Order No. KX-TCA1-G (KX-TCA1)
 
 Handset Cover . . . . . . . . . . . . . . . . . . . .one
Order No. PQKK10137Z1
 Battery . . . . . . . . . . . . . . . . . . .  one
Order No. P-P511
 Belt Clip . . . . . . . . . . . . . . . . . .  one
Order No. PQKE10363Z1
AC Adaptor Power Outlet 
(AC 120 V, 60 Hz)
12
2
1 
						

							 
– 2 – 
Charging the battery 
Place the handset on the charger and charge for 
 
about 6 hours 
 before initial use. 
•The unit beeps once, the CHARGE indicator 
lights and “ 
Charging 
” is displayed.
•When the battery is fully charged, “  
Charge 
completed 
” is displayed if there are no new 
calls in the Caller List.
•Recharge the battery when:
— “ 
Recharge battery 
” is displayed,
— “” flashes on the display, or
—the handset beeps intermittently while it is in 
use.
•If the battery has been discharged, the handset 
will display “ 
Charge for 6 HRS 
” and “” 
when you place the handset on the charger. The 
handset will not work unless the battery is 
charged. Keep charging. 
Handset battery information 
After your Panasonic battery is fully charged:
• 
Clean the charge contacts of the handset and the charger with a soft, dry cloth 
once a month. Clean more often if the unit is subject to grease, dust or high 
humidity. 
 Otherwise the battery may not charge properly. 
Belt Clip 
You can hang the handset on your belt or pocket using the belt clip. 
To attach the belt clip To remove the belt clip   
Operation
Operating time  
While in use (TALK) Up to 4.5 hours
While not in use (Standby) Up to 11 days
While using the Reception Booster feature  Up to 3 hours
CHARGE 
Indicator Charge Contacts
A
B
A
B
While pressing the top of the clip ( ), 
pull the right edge in the direction of the 
arrow ( ).A
B 
						

							 
– 3 – 
For assistance, please call: 1-800-211-PANA(7262) 
Registration 
This cordless handset must be registered to a KX-TG5100/KX-TG5110 base unit. The 
handset will be assigned the extension number at registration. Only one handset can be 
registered at a time. 
Charge the battery fully. Make sure the base unit and the other handsets are not 
being used. Registration must be completed within 1 minute.  
The handset display shows the instructions as shown on 
the right.
•The registered number “ 
[1] 
” to “ 
[8] 
” is shown on the top right of the display. 
•You can stop registration by pressing  
[OFF] 
 on the handset and pressing  
[MUTE]  
 on the 
base unit. 
1 
Base unit: 
 Press  
[MUTE] 
. 
•The MUTE indicator flashes. 
2 
Handset: 
(1) Press the soft key ( 
  
 
). 
(2) Wait until a long beep sounds and the display 
shows the registered number. 
•Registration is complete.
To cancel the handset registration, please see the KX-TG5100/KX-TG5110 Operating 
Instructions.
O KO K
              [-]
Press MUTE on
base unit, then
OK on handset to
register handset
O KO K
              [-]Press MUTE on
base unit, then
OK on handset to
register handset
[MUTE] Button and 
IndicatorTo operate “
  ”,
press the right soft key.OK
Press MUTE on
base unit, then
OK on handset to
register handset
           
O K
OK                                        
Handset 
  Registering
[-]
                                        
Handset [2]
   Registered
[2]Ex. Extension number 2 
						

							 
– 4 – 
Optional Headset 
Plugging the optional headset into the handset allows for hands-free phone conversation. 
Please use only a Panasonic KX-TCA60, KX-TCA86, KX-TCA88, KX-TCA91, 
KX-TCA92 or KX-TCA98. To order, call the accessories telephone number on page 1. 
Connecting an optional headset 
Open the headset jack cover, and connect the optional headset to the headset jack as 
shown below.  
•Headset sold separately. Model shown here is KX-TCA88. 
Wall Mounting 
The charger can be wall mounted. Connect the AC adaptor. Install screws using the wall 
template (see below). Mount the charger ( ). Slide it down ( ), then slide down to the 
right ( ) until it is secured.
Headset Jack
12
3
$
#
%
$
#
%
6.15 cm(2 13⁄32)
Screws 
To Power 
Outlet 
 
6.15 cm (2  
13
 
⁄ 
32
 
) 
Wall Template 
						

							 
– 5 – 
For assistance, please call: 1-800-211-PANA(7262) 
FCC and Other Information 
WHEN PROGRAMMING EMERGENCY NUMBERS AND(OR) MAKING TEST CALLS TO 
EMERGENCY NUMBERS:
1. Remain on the line and briefly explain to the dispatcher the reason for the call.
2.
Perform such activities in the off-peak hours, such as early morning or late evenings.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following 
two conditions: (1) This device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesired 
operation.
Privacy of communications may not be ensured when using this phone. 
CAUTION: 
Any changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate this device.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses, and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one or more of the following 
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver 
is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Operating near 5.8GHz electrical appliances may cause interference. Move away from the 
electrical appliances.
CAUTION:
To comply with FCC RF exposure requirements, the base unit should be installed with its 
antenna located at 20 cm or more from persons and handset should be carried with the 
specific belt-clip provided for the handset to ensure compliance. Other non-tested belt-clips 
or similar body-worn accessories may not comply, therefore, should be avoided.
This equipment is hearing aid compatible as defined by the FCC in 47 CFR Section 68.316. 
When you hold the phone to your ear, noise might be heard in your Hearing Aid. Some 
Hearing Aids are not adequately shielded from external RF (radio frequency) energy. If 
noise occurs, use an optional headset accessory or the speakerphone option (if 
applicable) when using this phone. Consult your audiologist or Hearing Aid manufacturer 
about the availability of Hearing Aids which provide adequate shielding to RF energy 
commonly emitted by digital devices. 
						

							– 6 –
CAUTION:
To reduce the risk of fire or injury to persons, read and follow these instructions.
1. Use only the battery(ies) specified.
2. Do not dispose of the battery(ies) in a fire. They may explode. Check with local waste 
management codes for special disposal instructions.
3. Do not open or mutilate the battery(ies). Released electrolyte is corrosive and may 
cause burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed.
4. Exercise care in handling batteries in order not to short the battery to conductive 
materials such as rings, bracelets, and keys. The battery and/or conductor may 
overheat and cause burns.
5. Charge the battery(ies) provided with or identified for use with this product only in 
accordance with the instructions and limitations specified in this manual.
A nickel cadmium battery that is recyclable powers the product you 
have purchased. At the end of its useful life, under various state and 
local laws, it is illegal to dispose of this battery into your municipal 
waste stream. Please call 1-800-8-BATTERY for information on how 
to recycle this battery.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT 
TO RAIN OR ANY TYPE OF MOISTURE.
•The AC adaptor is used as the main disconnect device, ensure that the AC outlet is 
located/installed near the unit and is easily accessible.
For your future reference
Serial No.                                           Date of purchase                      
(found on the bottom of the unit)
Name and address of dealer                                                                                      
Panasonic World Wide Web  address:  http://www.panasonic.com
for customers in the USA or Puerto Rico
Panasonic’s e-mail address for customer inquiries:
[email protected]
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
One Panasonic Way, Secaucus, New Jersey 07094
Panasonic Sales Company,
Division of Matsushita Electric of Puerto Rico, Inc.
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park
Carolina, Puerto Rico 00985
If you need assistance with the set-up or operation, 
please call 1-800-211-PANA(7262) 
						

							Unidad portátil inalámbrica de 5.8GHz ampliable
Modelo 
KX-TGA510M
Manual de instalación
LEA ESTAS INSTRUCCIONES ANTES DE LA UTILIZACIÓN Y 
GUÁRDELAS.
Esta unidad portátil es un accesorio inalámbrico, para ser usado con las unidades base de 
Panasonic KX-TG5100/KX-TG5110. Este manual de instalación describe únicamente los 
pasos necesarios para iniciar el funcionamiento de la unidad portátil. Lea las instrucciones 
de funcionamiento de KX-TG5100/KX-TG5110 para obtener más detalles
.
Instalación
Conexión de la unidad de carga
•Use solamente con el adaptador de CA KX-TCA1 de P anasonic (N.° de pedido KX-TCA1-G).
•El adaptador de CA deberá permanecer conectado en todo momento. (Durante la 
utilización es normal que se caliente el adaptador.)
Instalación de la batería
Inserte la batería ( ), y empújela hacia abajo hasta que encaje con un 
chasquido en su compartimento ( ).
 Una vez encajada, cierre la cubierta.
Accesorios (incluidos)  Para solicitar accesorios extra, llame al 1-800-332-5368.
 Unidad de carga  . . . . . . . . . . . . . . . . . . . . . 1
Cargador N.° de pedido PQLV30019ZM
Adaptador de CAN.° de pedido KX-TCA1-G (KX-TCA1)
 Cubierta de la unidad portátil  . . . . . . . . . . . 1
N.° de pedido PQKK10137Z1
 Batería  . . . . . . . . . . . . . . . . . . . . . 1
N.° de pedido P-P511
 Presilla para el cinturón  . . . . . . . . 1
N.° de pedido PQKE10363Z1
Adaptador de CATomacorriente
(CA 120 V, 60 Hz)
1
2
2
1
– (1) – 
						

							Carga de la batería
Ponga la unidad portátil en el cargador y cárguela 
durante 6 horas aproximadamente antes de 
utilizarla por primera vez.
•Sonará un pitido, el indicador CHARGE se encenderá y 
se visualizará “Charging”.
•
Cuando la batería está completamente cargada, “Charge 
completed” aparece en pantalla si no hay llamadas 
nuevas en la lista de personas que llaman.
•Cargue la batería cuando:
— se visualice “Recharge battery”,
— “” parpadee en la pantalla, o
—la unidad portátil emita pitidos intermitentemente 
mientras se utiliza.
•Si la batería se ha descargado, la unidad portátil 
visualizará “Charge for 6 HRS” y “” cuando la 
ponga en el cargador. La unidad portátil no funcionará a no ser que la batería esté 
cargada. Deje que se cargue.
Información acerca de la batería de la unidad portátil
Después de que su batería Panasonic esté completamente cargada:
•Limpie los contactos de carga de la unidad portátil y del cargador con un paño 
suave y seco una vez al mes. Limpie más a menudo si la unidad está expuesta a la 
grasa, polvo o humedad alta. De lo contrario, la batería tal vez no se cargue 
correctamente.
Presilla para cinturón
Podrá colgar la unidad portátil en su cinturón o bolsillo utilizando la presilla para cinturón.
Para colocar la presilla para cinturónPara quitar la presilla para cinturón 
OperaciónTiempo de operación
Mientras se utiliza (HABLAR) Hasta 4.5 horas
Mientras no se utiliza (Espera) Hasta 11 días
Mientras se utiliza la función Reception Booster  Hasta 3 horas
Indicador 
CHARGE Contactos 
de carga
A
B
Mientras presiona la parte superior de 
la presilla ( ), tire del borde derecho 
en el sentido de la flecha ( ).
A
B
– (2) – 
						

							Registro
Esta unidad portátil deberá ser registrada a una unidad base KX-TG5100/KX-TG5110. 
El número de extensión de la unidad portátil será asignado al hacer el registro. Solamente 
podrá registrarse una unidad portátil cada vez.
Cargue la batería completamente. Asegúrese de que la unidad base y las otras 
unidades portátiles no estén siendo utilizadas. El registro deberá completarse antes 
de 1 minuto. 
El visualizador de la unidad portátil muestra las instrucciones 
como se muestra a la derecha.
•El número de registro “[1]” a “[8]” se mostrará en la parte superior derecha del 
visualizador. 
•Podrá parar el registro presionando [OFF] en la unidad portátil y presionando [MUTE] en 
la unidad base.
1Unidad base: Presione [MUTE].
•La luz del indicador MUTE parpadeará.
2Unidad portátil:
(1) Presione la tecla blanda (
  ).  
(2) Espere hasta que suene un pitido largo y el 
visualizador muestre el número registrado.
•Entonces se habrá completado el registro.
Para cancelar el registro de la unidad portátil, consulte las instrucciones de 
funcionamiento de KX-TG5100/KX-TG5110.
O KO K
              [-]
Press MUTE on
base unit, then
OK on handset to
register handset
O KO K
              [-]Press MUTE on
base unit, then
OK on handset to
register handset
Botón e indicador [MUTE]Para accionar “
  ”,
presione la tecla blanda 
derecha.OK
Press MUTE on
base unit, then
OK on handset to
register handset
           
O K
OK                                        
Handset 
  Registering
[-]
                                        
Handset [2]
   Registered
[2]
Ej., Número de extensión 2 
– (3) – 
						

							Auricular opcional
Enchufando un auricular opcional a la unidad portátil podrá conversar por teléfono con las 
manos libres. Utilice solamente un auricular Panasonic KX-TCA60, KX-TCA86, 
KX-TCA88, KX-TCA91, KX-TCA92 o KX-TCA98. Para hacer el pedido, llame al número de 
teléfono para accesorios de la página 1.
Conexión del auricular opcional
Abra la tapa de la toma para auricular y conecte el auricular opcional a la toma para 
auricular como se muestra.  
•El auricular se veude separado. El modelo semuestra aqui es KX-TCA88.
Montaje en pared
El cargador puede montarse en una pared. Conecte el adaptador de CA. Instale los tor nillos 
utilizando la plantilla para pared (consulte más abajo). Monte el cargador ( ). Deslícelo hacia 
abajo ( ) y después hacia abajo y hacia la derecha ( ) hasta fijarlo en su sitio.
Toma para auricular
1
23
$
#
%
6.15 cm(2 13⁄32)
Tornillos 
A la 
tomacorriente
6.15 cm (2 13⁄32)PLANTILLA PARA PARED
– (4) –