Panasonic Kx Tga405 Installation Guide

							Installation Guide for Range Extender
By installing this unit, you can extend the range of your phone system to include 
areas where reception was previously not available. 
The unit extends the range in all directions, allowing several floors to be covered.
Important:
LThis unit is an accessory unit for use with Panasonic Digital Cordless phones.
LThis unit is pre-registered to the base unit.
LThis leaflet only describes the steps needed to install and use the unit. Refer to the 
base unit’s operating instructions for accessory information, important information 
for safety, FCC and other information (for U.S.A. users only), and Industry Canada 
Notices and other information (for Canada users only).
For best performance
Placement
LInstall the unit within base unit range in an indoor environment. We recommend 
installing the unit in a raised position (such as on a wall).
LAvoid positioning the unit close to objects that will interfere with reception, such as 
thick walls, radiators, metal shelving, etc.
LFor maximum distance noise-free operation, place the unit away from electrical 
appliances such as TV, radio, personal computer, or other telephone equipment.
LKeep an appropriate distance from the base unit to maximize the range of your 
phone system. Find the appropriate location by checking the w indicator. If the w 
indicator lights red or amber, re-position this unit in a place where the w indicator 
lights green.Model No.
Range Extender
KX-TGA405
KX-TGA405C
Base unitHandset
Range extender
Range extender range Base unit range
PNQW1965ZB    DC1209SN1020  (A) Printed in China
TGA405(bundle)(e).fm  Page 1  Thursday, February 4, 2010  10:12 AM 
						

							– 2 –
Controls
Understanding the STATUS indicator and w indicator
Installation
1Connect the unit.
LUse only the supplied Panasonic AC adaptor PQLV219.
LWhen the unit is turned on, the STATUS indicator and w indicator light amber 
for about 2 seconds.ASTATUS indicator
Bw indicator
ID indicator
C{PROGRAM}
IndicatorLight statusMeaning
STATUS
indicatorGreen OnLWithin base unit range. The unit is ready for 
use.
FlashingL1 handset is communicating with the base 
unit through this unit.
Flashing
rapidlyL2 handsets are communicating with the base 
unit through this unit.
Red OnLOut of base unit range.
OffLThe power is off. (AC adaptor is not 
connected properly.)
w
indicatorGreen OnLSignal strength of the base unit is strong.
Amber OnLSignal strength of the base unit is weak.
Red OnLOut of base unit range.
OffLThe unit is not being used.
LThe power is off.
B
A
C
Press plug firmly.
(120 V AC, 60 Hz)  Hook
TGA405(bundle)(e).fm  Page 2  Thursday, February 4, 2010  10:12 AM 
						

							– 3 –
2Confirm that the STATUS indicator and w indicator light green. (The unit is 
ready for use.)
LIf the indicators do not light green, re-position the unit in a place where the 
indicators light green.
Note:
LThe AC adaptor must remain connected at all times. (It is normal for the adaptor to 
feel warm during use.)
LThe AC adaptor should be connected to a vertically oriented or floor-mounted AC 
outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight 
of the adaptor may cause it to become disconnected.
LThe unit can support a maximum of 2 handsets at a time.
LUp to 2 range extenders can be registered to the base unit.
Wall Mounting
Drive the screws (not supplied) into the wall. Mount the unit, then slide it down.
Note:
LMake sure that the wall is strong enough to support the weight of the unit.
Specifications
NStandard: DECT 6.0 (Digital Enhanced Cordless Telecommunications 6.0)
NFrequency range: 1.92 GHz to 1.93 GHz
NRF transmission power: 115 mW (max.)
NPower source: 120 V AC, 60 Hz
NPower consumption: Standby: Approx. 1.0 W, Maximum: Approx. 1.8 W
NOperating conditions:
0°C – 40°C (32°F – 104°F), 20 % – 80 % relative air humidity (dry)
Note:
LDesign and specifications are subject to change without notice.
LThe illustrations in these instructions may vary slightly from the actual product.
37.0 mm
(115/32 inches)
Screws
TGA405(bundle)(e).fm  Page 3  Thursday, February 4, 2010  10:12 AM 
						

							– 4 –
Troubleshooting
ProblemCause/solution
The unit does not work.LWhen the indicators do not light, the AC adaptor is not 
connected properly. Check the connections.
LWhen the indicators do not light green, move the unit 
closer to the base unit.
LRegistration may have been canceled.
Deregister the unit, then re-register.
Deregister:
1Unplug the AC adaptor, then press and hold 
{PROGRAM}.
2While pressing and holding {PROGRAM}, 
re-connect the AC adaptor.
3Keep pressing and holding {PROGRAM} for about 
10 seconds until the STATUS indicator flashes 
amber. Then release {PROGRAM}.
Re-register:
1Range extender: Unplug the AC adaptor.
2Base unit: Press and hold {LOCATOR} for about 
5 seconds until the registration tone sounds.
– The next step must be completed within 90 
seconds.
3Range extender: Connect the AC adaptor, then 
wait until the STATUS indicator lights green.
4Base unit: To stop the registration tone, press 
{LOCATOR}.
While talking using the 
handset, sound cuts in 
and out.LThe handset is out of range. Move the handset closer 
to this unit.
The STATUS indicator 
continues to light 
amber for a while.L{PROGRAM} was pressed. The unit is in 
programming mode. To exit, press {PROGRAM} 
again. Do not press {PROGRAM}, except when 
deregistering the unit.
TGA405(bundle)(e).fm  Page 4  Thursday, February 4, 2010  10:12 AM