Panasonic Kx Tda0490 Getting Started Manual

B2 Programming for the Extension Number Method
Getting Started 61
B2 Programming for the Extension Number 
Method
When programming the VoIP Gateway Cards and PBXs for use in a network configured for the 
extension number method instead of the PBX code method, some of the steps in the programming 
procedures require different setting values.
The following 2 sections provide specific steps that require different setting values. The steps other 
than those provided here have common setting values, and are...

B2 Programming for the Extension Number Method
62 Getting Started
Program an address translation table with the setting values shown below, following the procedure in 
3.2.5 Programming the Address Translation Table.
Programming the VoIP Gateway Card in the Chicago Office
Create hunt patterns with the setting values shown below, following the procedure in Assigning the 
Hunt Pattern under 3.3 Programming the VoIP Gateway Card in the Chicago Office. 

B2 Programming for the Extension Number Method
Getting Started 63
B2.2 Programming the PBX in the Los Angeles Office
The steps below are provided in substitution for steps 6 and 7 of the procedure detailed in 4.1 
Programming the PBX in the Los Angeles Office. Program the PBX in the Los Angeles office using 
the extension number method, following these steps.
After programming the PBX in the Los Angeles office, follow the same procedure to program the PBX 
in the Chicago office with the appropriate...

B2 Programming for the Extension Number Method
64 Getting Started
Step 8
Assign the routing information to route calls to the remote PBX:
In the Leading Number box, type 3 (for the Chicago office extensions), 6 (for the Chicago office fax 
extensions), and 93 (for Chicago office PSTN access).
Note
Do not set any value in the Own PBX Code box.
After the above step, follow step 8 of the procedure in 4.1 Programming the PBX in the Los Angeles 
Office. 

Getting Started 65
Appendix C
Initialization of the VoIP Gateway Card 

C1 Initializing the VoIP Gateway Card
66 Getting Started
C1 Initializing the VoIP Gateway Card
In case you have forgotten, for example, the IP address or log-in password you set to the VoIP 
Gateway Card, follow the procedure below to return the settings of the card to the factory default.
Note
Resetting the card will restore all settings, not just the IP address and log-in password, to the 
factory default.
1.Install the card to the PBX, and then turn on the power to the PBX.
2.Using the KX-TDA...

Getting Started 67
Appendix D
Using the KX-TDA0490 and KX-TDA0480 in One
Network 

D1 Considerations in Installation
68 Getting Started
D1 Considerations in Installation
Provided below are the points to consider when the VoIP network contains both the KX-TDA0490 and 
KX-TDA0480 VoIP Gateway Cards.
Adding the KX-TDA0490 to the Network Using the KX-TDA0480 Maintenance Console 
Software
For the KX-TDA0480 to recognize the KX-TDA0490 in the network, you must add it as an Other Unit 
in a Unit Group (network) when programming with the MCS as shown below:
Note
For programming instructions...

D1 Considerations in Installation
Getting Started 69 

Panasonic Consumer Electronics Company
Division of Matsushita Electric Corporation of America
One Panasonic Way
Secaucus, NJ 07094
Panasonic Sales Company
Division of Matsushita Electric of Puerto Rico, Inc.
Ave. 65 de Infantería, Km. 9.5 
San Gabriel Industrial Park
Carolina, Puerto Rico 00985
http://www.panasonic.com/csd
Copyright:
This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced for internal use 
only. All other reproduction, in whole or in part, is prohibited...