Panasonic Kx T1451 Operating Instructions Manual

EASA-PHONE
Panasonic
^f,[i,1?,1;3i:i#
KX-T1 450
MoDEL*o KX-T1 451 

Table of Contents
Locations of the Controls . . . .
Introduction
Preparation
CoNNECTTON . .. ..
INITIAL SETTINGS
TOLL SAVER
CASSETTE TAPE INSTALLATION
How to Record an Outgoing Message (OGM)
RECORDING THE OGM
CHECKING YOUR OGM
SAMPLE OGMS
Setting Prior to Leaving
RECORDING THE CALLERS MESSAGES ....PREPARING THE ICM TAPE
Listening to the Recorded Messages
LISTENINGTOTHEMESSAGES .,......10RE-PLAYINGBACKALLTHEMESSAGES . ...... 10
Other Features
RECORDTNG A PERSONAL MESSAGE (MESSAGE MEMO) ..... 11SAVING THE...

VOLUME CONTROL(page 13)
REMOTE CODE Selector(page 5)
Telephone Jack (page 4)
Telephone Line Jack (page 4)
DC Jack (page 4)
Keep this overleaf unfolded while you are
reading this Operating lnstructions. This
makes it easier to locate the controls and
switches mentioned in the instructions.
-2-
Introduction
Thank you for purchasing the Panasonic Telephone
Answering System.
You can use tfris Model KX-T1450|KX-T1451 to:
I Answer calls and record messages when you cannot answer the telephone or do
not want to...

Preparation
CONNECTION
,&-->: //( ..,t
W=/ sinsre-Linererephone
l1
f.I
f;
I
To Power Outlet(AC120 V,60 Hz)
Do not connect the AC adaptor to
the AC outlet before inserting the::OGM and ICM tapes. (See page 6.)
Holder
Fasten the cord to the holder
Jack (RJ1 1 C)
oUSE ONLY PANASONIC AC ADAPTOR KX-AI1.
oThe unit must not be connected to a coin operated line. lf you are on a party line,
check with your local telephone company.
oWhile operating the unit, the cabinet of the AC Adaptor may feel warm, this is a...

Preparation
INITIAL SETTINGS
Calling Party Control (CPC) Setting
Set to A. (no call waiting service line.)
lf you have call waiting service or
some Incoming Messages are
interrupted, set to 8.
Number ot Rings
o2.............. The unit will answer a call on the
second ring.
o4.............. The unit will answer a call on
the fourth ring.
oAUTO...... See TOLL SAVER on this
page.
Recording Time Selector
oVOX........ The unit will record for as long as
the caller soeaks.
o1 minute.. The unit will record uo...

How to Record an Outgoing Message (OGM)
Before operating your unit, you must record an Outgoing Message (OGM).
The OGM will inform the calling party of your absence and your message.
RECORDING THE OGM
/ Push OGM REC until a long beep is
heard. then release it.
After the long beep, speak clearly and
loudly into the microphone (MlC),
approximately 8 inches away.
oThe lN USE indicator will flash.oThe recording time is up to the tape
length that you use.
When recording is finished, push OGM
REC again.
oThe...

Setting Prior to Leaving
RECORDING THE CALLERS MESSAGES
1 Push POWER ON/OFF to ON.
oThe POWER indicator will lioht.
NOTES:
oThe unit will automatically switch itself to
the Answer mode 7 seconds after you set
the POWER ON/OFF switch or you
complete some other operations. When the
telephone rings, the unit will play back your
OGM, then it will record the callers
messages on the tape.
rlf you do not want to set the unit to the
Answer mode, set the POWER ON/OFF
switch to OFF.
PREPARING THE ICM TAPE
After...

rOther Featur 
-.f
Other Features
BECORD,NG A PERSONAL MESSAGE (MESSAGE MEMO)
You may record a personal message any time at home on the ICM tape. lt will be
heard by anyone retrieving messages lrom the unit.
1 Push MEMO until a beep is heard.
Speak into the MlC.
oThe lN USE indicator will flash.
3 Wnen finished recording, push MEMO
again.
oThe lN USE indicator will stop flashing.
oThe ANSWER/CALL indicator will flash
to show that your message was
recorded, and the unit will be ready to
answer the phone...

rOther Features
ERASING THE RECORDED MESSAGES
After you have played back the recorded messages, you can erase them by simply
pushing the ICM ERASE button.
7 Push ICM ERASE until a beep is heard.
oThe unit will erase the recorded
messages while the tape is rewinding.
NOTE:
The taoe can be erased even if the
record-prevention (knock-out) tabs have been
removed.
MONITORING THE INCOMING CALLS
While an Incoming Message is being recorded, you can hear it, then you may
choose to pick up the telephone handset...

r\
@
m
/z-\
t_trI_J
How to Operate from a Remote Phone
PLAYING BACK MESSAGES
You can listen to the recorded messages by simply pushing your own code number.
1 Catt your unit, and push the Code No. (2 digits) during the OGM.
oA beep will sound, then other beeps will sound to tell you the
number of recorded messages, up to 8 times.
oThe unit will rewind the tape to the beginning. After a series of
short beeps, you will hear all the messages on the tape.
2 Listen to the recorded messages.
o3 beeps will be...