Panasonic Interactive Plasma Display Th 65pb1 Operating Instructions

Ferrite core × 2Use the Ferrite cores to comply with the EMC standard.
(See page 15)
Accessories
Accessories Supplied
Check that you have the Accessories and items shown
Operating
Instruction book Remote Control Transmitter
N2QAYB000691Batteries for the 
Remote Control 
Transmitter
(AA Size × 2)
AC cord
Clamper × 1
TMME289 J0KG00000014
Software DVD-ROM × 1
• elite Panaboard software
• elite Panaboard book
• Operating Instructions
     Display Operations     Network Operations     Electronic Pen...

+
-+
-
Requires two AA batteries.2.  Insert batteries - note correct polarity (+ and -).
  Precaution on battery use
Incorrect installation can cause battery leakage and corrosion that will\
 damage the remote control transmitter.
Disposal of batteries should be in an environment-friendly manner.
Observe the following precautions:
1. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set.
2. Do not combine a used battery with a new one.
3. Do not mix battery...

13
Connections
Speaker connection
1 2
Plug the AC cord into the display unit.
Plug the AC cord until it clicks.
Note:
Make sure that the AC cord is locked on 
both the left and right sides.
AC cord fi xing
Unplug the AC cord
Unplug the AC cord pressing the 
two knobs.
Note:
When disconnecting the AC cord, be 
absolutely sure to disconnect the AC 
cord plug at the socket outlet fi  rst.
Using the clamper
Secure any excess cables with clamper as required.
Note:
One clamper is supplied with this unit. In case...

14
(8Ω,20W[10W+10W ])
Connections
Video equipment connection
SLOT:  
Terminal board (optional 
accessories) insert slot
(see page 5)
Note:
The right side slot is for terminal board 
with 2-slot width. The terminal board 
with 1-slot width does not function when 
installed in the right side slot.
AV IN (HDMI): 
HDMI Input Terminal
Connect to video equipment 
such as VCR or DVD player.WIRELESS 
MODULE, LAN: 
See page 15DVI-D IN:  DVI-D Input Terminal
PC IN:   PC Input Terminal Connect to video terminal of...

15
Example of Network Connection (Wired LAN)
Connections
To use the wireless function, the wireless module (ET-WM200U) (sold separately) is necessary.
When connecting the wireless module to the 
display, remove the protective fi lm and cap.
Connecting procedure Hold the wireless module with its LED on the near 
side and connect it to the wireless module connection 
terminal.
Note:
Do not connect any other device than the wireless 
module (ET-WM200U).
 When using the electronic pen
Using the electronic pen...

INPUT MENUENTER/+/
VOL-/
16
Power Indicator
Remote Control Sensor
Power ON / OFF
Connecting the AC cord plug to the Plasma Display.
Connecting the plug to the Wall Outlet.
Note: 
When disconnecting the AC cord, be absolutely sure to 
disconnect the AC cord plug at the socket outlet  fi rst.
Press the Power switch on the Plasma Display to turn the 
set on: Power-On. Power Indicator: Green
[Starting up the network]
It takes some time for the network to start up just after the 
power is turned on.
During...

English (UK) Deutsch 
Français   
Italiano 
 
Español 
 
ENGLISH (US) 
Русский  OSD LANGUAGE
SET 
SELECT 
DAY/TIME SETUPTIME    MON  99:99
SET
TIME99:99DAY MON
DAY/TIME SETUPTIME    MON  99:99
SET
TIME10:00DAY TUE
LANDSCAPE
PORTRAIT
DISPLAY ORIENTATION
When 3D images will be viewed by unspeci fi ed number of 
people or used for commercial applications, someone in 
authority should convey the following precautions.
These precautions should be followed in the home as well.
To enjoy 3D images safely and...

INPUT MENUENTER/+/
VOL-/
18
MENU Screen ON / OFF
Each time the MENU button is pressed, the menu screen 
will switch.
INPUT button (Input signal selection)
Basic Controls
Main Power On / Off Switch
Power Indicator
The Power Indicator will light.
• Power-OFF .... Indicator not illuminated (The unit will  still consume some power as long as 
the power cord is still inserted into the 
wall outlet.)
• Standby  ........ Red Orange (When “Slot power” is set to “On”.)
Orange (Depending on the type of the...

19
Basic Controls
Remote Control Transmitter
RECALL buttonPress the “RECALL” button to 
display the current system status.
1  Input  label2  Aspect  mode 
  During 3D images    Audio input 
  Profi  le name
    NANODRIFT SAVER operating
3  Touch Pen mode ON/OFF
4  Off  timer
    The off timer indicator is 
displayed only when the off 
timer has been set.
5 Clock  display
TOUCH-PENON
1
2
3PC4:3
♪  COMPONENTMEMORY NAME: MEMORY2
NANODRIFT3D
OFF  TIMER90MIN4510:00
Standby (ON / OFF) button
The Plasma Display...

20
Specifi cations
TH-65PB1U
Power Source  110 - 127 V AC, 50/60 Hz
Power Consumption Rated Power Consumption 555 W
Stand-by condition 0.4 W
Power off condition 0.2 W
Plasma Display panel Drive method : AC type 65-inch, 16:9 aspect ratio
Screen size 56.4” (1,434 mm) (W) × 31.7” (806 mm) (H) × 64.7”\
 (1,645 mm) (diagonal)
(No.of pixels) 2,073,600 (1,920 (W) × 1,080 (H))
[5,760 × 1,080 dots]
Operating condition Temperature 32 °F - 104 °F (0 °C - 40 °C)
Humidity 20 % - 80 %
Applicable signals Color System...