Home
>
Panasonic
>
Camera Accessories
>
Panasonic Indoor Pan Tilt Head Awrc400n Operating Instructions
Panasonic Indoor Pan Tilt Head Awrc400n Operating Instructions
Here you can view all the pages of manual Panasonic Indoor Pan Tilt Head Awrc400n Operating Instructions . The Panasonic manuals for Camera Accessories are available online for free. You can easily download all the documents as PDF.
Page 51
51 Example of system configuration Convertible camera MONITOR1 MonitorMonitor Cable provided with AW-CB400 Monitor switching AW-RC400 Cable Compensation Unit AW-PS505 AC adaptor Pan/Tilt Control Panel AW-RP400 Remote Operation Panel AW-CB400 Headset Headset MONITOR2 Pan/tilt head and camera control Indoor Pan/Tilt Head AW-PH400 Composite video or component video signals To switcher, monitor Genlock signals G/L AW-PS301 AC adaptor
Page 52
![Page 52
52
Operating procedures
$Turning on the power
1 When using one AW-RP400, set its EXT CONT [M/S] switch to the [M] positi\
on.
When two AW-RP400 units are used, set the EXT CONT [M/S] switch on the A\
W-RP400 to which the pan/tilt head is
connected to the [M] (master) position and the switch on the AW-RP400 \
to which the pan/tilt head is not connected to the
[S] (slave) position.
\b Turn on the power.
Follow the sequence below to turn on the power when one AW-RP400 is goin\
g to be used: Set the power...](http://img.usermanuals.tech/thumb/58/68258/w300_awrc400n_en_om_d-51.png "Page 52
52
Operating procedures
$Turning on the power
1 When using one AW-RP400, set its EXT CONT [M/S] switch to the [M] positi\
on.
When two AW-RP400 units are used, set the EXT CONT [M/S] switch on the A\
W-RP400 to which the pan/tilt head is
connected to the [M] (master) position and the switch on the AW-RP400 \
to which the pan/tilt head is not connected to the
[S] (slave) position.
\b Turn on the power.
Follow the sequence below to turn on the power when one AW-RP400 is goin\
g to be used: Set the power...")
52 Operating procedures $Turning on the power 1 When using one AW-RP400, set its EXT CONT [M/S] switch to the [M] positi\ on. When two AW-RP400 units are used, set the EXT CONT [M/S] switch on the A\ W-RP400 to which the pan/tilt head is connected to the [M] (master) position and the switch on the AW-RP400 \ to which the pan/tilt head is not connected to the [S] (slave) position. \b Turn on the power. Follow the sequence below to turn on the power when one AW-RP400 is goin\ g to be used: Set the power...
Page 53
![Page 53
53
Operating procedures
6To set the counterclockwise limit of the roll unit, use the ROTATION swi\
tch to rotate the roll unit as far as the limit in the
counterclockwise direction which is to be set.
While holding down the MENU/LIMIT button, press the PRESET MEMORY button\
[25].
Once the limit is set, the lamp of the PRESET MEMORY button [45] will li\
ght.
To release the setting, press the PRESET MEMORY button [25] again while \
holding down the MENU/LIMIT button.
Once the setting is released, the lamp...](http://img.usermanuals.tech/thumb/58/68258/w300_awrc400n_en_om_d-52.png "Page 53
53
Operating procedures
6To set the counterclockwise limit of the roll unit, use the ROTATION swi\
tch to rotate the roll unit as far as the limit in the
counterclockwise direction which is to be set.
While holding down the MENU/LIMIT button, press the PRESET MEMORY button\
[25].
Once the limit is set, the lamp of the PRESET MEMORY button [45] will li\
ght.
To release the setting, press the PRESET MEMORY button [25] again while \
holding down the MENU/LIMIT button.
Once the setting is released, the lamp...")
53 Operating procedures 6To set the counterclockwise limit of the roll unit, use the ROTATION swi\ tch to rotate the roll unit as far as the limit in the counterclockwise direction which is to be set. While holding down the MENU/LIMIT button, press the PRESET MEMORY button\ [25]. Once the limit is set, the lamp of the PRESET MEMORY button [45] will li\ ght. To release the setting, press the PRESET MEMORY button [25] again while \ holding down the MENU/LIMIT button. Once the setting is released, the lamp...
Page 54
![Page 54
54
Operating procedures
$Genlock adjustments for the respective cameras
For details on the genlock adjustments, refer to the operating instructi\
ons of the AW-CB400 remote operation panel or
WV-CB700A remote control box.
$Video adjustments for the cameras
Adjust the total pedestal (black level), white balance, black balance,\
etc. of the cameras.
For details on the camera adjustments, refer to the operating instructio\
ns of the AW-CB400 remote operation panel or
WV-CB700A remote control box....](http://img.usermanuals.tech/thumb/58/68258/w300_awrc400n_en_om_d-53.png "Page 54
54
Operating procedures
$Genlock adjustments for the respective cameras
For details on the genlock adjustments, refer to the operating instructi\
ons of the AW-CB400 remote operation panel or
WV-CB700A remote control box.
$Video adjustments for the cameras
Adjust the total pedestal (black level), white balance, black balance,\
etc. of the cameras.
For details on the camera adjustments, refer to the operating instructio\
ns of the AW-CB400 remote operation panel or
WV-CB700A remote control box....")
54 Operating procedures $Genlock adjustments for the respective cameras For details on the genlock adjustments, refer to the operating instructi\ ons of the AW-CB400 remote operation panel or WV-CB700A remote control box. $Video adjustments for the cameras Adjust the total pedestal (black level), white balance, black balance,\ etc. of the cameras. For details on the camera adjustments, refer to the operating instructio\ ns of the AW-CB400 remote operation panel or WV-CB700A remote control box....
Page 55
![Page 55
55
Operating procedures
3Press the START POINT button.
The lamps of the buttons among TRACING MEMORY buttons 1 to 10 where data\
can be registered now light. ≥ The lamps of the buttons with numbers exceeding the number of memories s\
et by the MEMORY LENGTH menu setting
do not light.
≥ If the lamp of any button among the number of memories in which data can\
be set is off, it means that data has already
been registered in the button. When registering data in such a button, d\
elete the existing data in...](http://img.usermanuals.tech/thumb/58/68258/w300_awrc400n_en_om_d-54.png "Page 55
55
Operating procedures
3Press the START POINT button.
The lamps of the buttons among TRACING MEMORY buttons 1 to 10 where data\
can be registered now light. ≥ The lamps of the buttons with numbers exceeding the number of memories s\
et by the MEMORY LENGTH menu setting
do not light.
≥ If the lamp of any button among the number of memories in which data can\
be set is off, it means that data has already
been registered in the button. When registering data in such a button, d\
elete the existing data in...")
55 Operating procedures 3Press the START POINT button. The lamps of the buttons among TRACING MEMORY buttons 1 to 10 where data\ can be registered now light. ≥ The lamps of the buttons with numbers exceeding the number of memories s\ et by the MEMORY LENGTH menu setting do not light. ≥ If the lamp of any button among the number of memories in which data can\ be set is off, it means that data has already been registered in the button. When registering data in such a button, d\ elete the existing data in...
Page 56
![Page 56
56
Operating procedures
1Select the pan/tilt head system using one of the CONTROL SELECT buttons.\
When using the AW-CB400 for camera control, select the same number for t\
he AW-CB400.
\b Press the button corresponding to the tracing memory whose registered da\
ta is to be changed, and call the start position.
3 Press the RESTORE button.
The pan/tilt head system starts the operation registered in the tracing \
memory, and the lamp of the STOP button flashes.
As when the data was registered, the PRESET...](http://img.usermanuals.tech/thumb/58/68258/w300_awrc400n_en_om_d-55.png "Page 56
56
Operating procedures
1Select the pan/tilt head system using one of the CONTROL SELECT buttons.\
When using the AW-CB400 for camera control, select the same number for t\
he AW-CB400.
\b Press the button corresponding to the tracing memory whose registered da\
ta is to be changed, and call the start position.
3 Press the RESTORE button.
The pan/tilt head system starts the operation registered in the tracing \
memory, and the lamp of the STOP button flashes.
As when the data was registered, the PRESET...")
56 Operating procedures 1Select the pan/tilt head system using one of the CONTROL SELECT buttons.\ When using the AW-CB400 for camera control, select the same number for t\ he AW-CB400. \b Press the button corresponding to the tracing memory whose registered da\ ta is to be changed, and call the start position. 3 Press the RESTORE button. The pan/tilt head system starts the operation registered in the tracing \ memory, and the lamp of the STOP button flashes. As when the data was registered, the PRESET...
Page 57
![Page 57
57
Operating procedures
1Select the pan/tilt head system using one of the CONTROL SELECT buttons.\
\b When the button corresponding to the registered preset memory data is pr\
essed, the pan/tilt head system is set to the
registered status.
Playing the preset memory data](http://img.usermanuals.tech/thumb/58/68258/w300_awrc400n_en_om_d-56.png "Page 57
57
Operating procedures
1Select the pan/tilt head system using one of the CONTROL SELECT buttons.\
\b When the button corresponding to the registered preset memory data is pr\
essed, the pan/tilt head system is set to the
registered status.
Playing the preset memory data")
57 Operating procedures 1Select the pan/tilt head system using one of the CONTROL SELECT buttons.\ \b When the button corresponding to the registered preset memory data is pr\ essed, the pan/tilt head system is set to the registered status. Playing the preset memory data
Page 58
![Page 58
58
Cable specifications
When an IAS, WAS or VAS lens (analog drive) made by Canon is used
Connect to the LENS I/F2
connector on pan/tilt head.
❈The cable lengths are approximate. Ensure that their lengths are approp\
riate for the actual system used.
Connector: 10136-3000VE made by Sumitomo 3M
Case: 10336-52F0-008 made by Sumitomo 3M
Connector: SR30-10PE-6P made by Hirose Electric
Connect to the FOCUS connector on lens.Cable length: At least 800 mm or so
Connector: R01-01P9-8M made by Tajimi Musen...](http://img.usermanuals.tech/thumb/58/68258/w300_awrc400n_en_om_d-57.png "Page 58
58
Cable specifications
When an IAS, WAS or VAS lens (analog drive) made by Canon is used
Connect to the LENS I/F2
connector on pan/tilt head.
❈The cable lengths are approximate. Ensure that their lengths are approp\
riate for the actual system used.
Connector: 10136-3000VE made by Sumitomo 3M
Case: 10336-52F0-008 made by Sumitomo 3M
Connector: SR30-10PE-6P made by Hirose Electric
Connect to the FOCUS connector on lens.Cable length: At least 800 mm or so
Connector: R01-01P9-8M made by Tajimi Musen...")
58 Cable specifications When an IAS, WAS or VAS lens (analog drive) made by Canon is used Connect to the LENS I/F2 connector on pan/tilt head. ❈The cable lengths are approximate. Ensure that their lengths are approp\ riate for the actual system used. Connector: 10136-3000VE made by Sumitomo 3M Case: 10336-52F0-008 made by Sumitomo 3M Connector: SR30-10PE-6P made by Hirose Electric Connect to the FOCUS connector on lens.Cable length: At least 800 mm or so Connector: R01-01P9-8M made by Tajimi Musen...
Page 59
![Page 59
59
Cable specifications
When an IASD, WASD or VASD lens (digital drive) made by Canon is used
Connect to the LENS I/F2
connector on pan/tilt head.
❈The cable lengths are approximate. Ensure that their lengths are approp\
riate for the actual system used.
Connector: 10136-3000VE made by Sumitomo 3M
Case: 10336-52F0-008 made by Sumitomo 3M
Connector: HR25-9P-20P made by Hirose Electric
Connect to the ZOOM/FOCUS
connector on lens.
Cable length: At least 800 mm or so
Connector: HR10A-10J-12P made by Hirose...](http://img.usermanuals.tech/thumb/58/68258/w300_awrc400n_en_om_d-58.png "Page 59
59
Cable specifications
When an IASD, WASD or VASD lens (digital drive) made by Canon is used
Connect to the LENS I/F2
connector on pan/tilt head.
❈The cable lengths are approximate. Ensure that their lengths are approp\
riate for the actual system used.
Connector: 10136-3000VE made by Sumitomo 3M
Case: 10336-52F0-008 made by Sumitomo 3M
Connector: HR25-9P-20P made by Hirose Electric
Connect to the ZOOM/FOCUS
connector on lens.
Cable length: At least 800 mm or so
Connector: HR10A-10J-12P made by Hirose...")
59 Cable specifications When an IASD, WASD or VASD lens (digital drive) made by Canon is used Connect to the LENS I/F2 connector on pan/tilt head. ❈The cable lengths are approximate. Ensure that their lengths are approp\ riate for the actual system used. Connector: 10136-3000VE made by Sumitomo 3M Case: 10336-52F0-008 made by Sumitomo 3M Connector: HR25-9P-20P made by Hirose Electric Connect to the ZOOM/FOCUS connector on lens. Cable length: At least 800 mm or so Connector: HR10A-10J-12P made by Hirose...
Page 60
![Page 60
60
Cable specifications
When an RD lens made by Fujinon is used
Connect to the LENS I/F2
connector on pan/tilt head.
❈The cable lengths are approximate. Ensure that their lengths are approp\
riate for the actual system used.
Connector: 10136-3000VE made by Sumitomo 3M
Case: 10336-52F0-008 made by Sumitomo 3M
Connector: HR10A-10P-12P made by Hirose Electric
Connect to the FOCUS connector on lens.Cable length: At least 800 mm or so
Connector: HR10A-10P-12P made by Hirose Electric
Connect to the ZOOM...](http://img.usermanuals.tech/thumb/58/68258/w300_awrc400n_en_om_d-59.png "Page 60
60
Cable specifications
When an RD lens made by Fujinon is used
Connect to the LENS I/F2
connector on pan/tilt head.
❈The cable lengths are approximate. Ensure that their lengths are approp\
riate for the actual system used.
Connector: 10136-3000VE made by Sumitomo 3M
Case: 10336-52F0-008 made by Sumitomo 3M
Connector: HR10A-10P-12P made by Hirose Electric
Connect to the FOCUS connector on lens.Cable length: At least 800 mm or so
Connector: HR10A-10P-12P made by Hirose Electric
Connect to the ZOOM...")
60 Cable specifications When an RD lens made by Fujinon is used Connect to the LENS I/F2 connector on pan/tilt head. ❈The cable lengths are approximate. Ensure that their lengths are approp\ riate for the actual system used. Connector: 10136-3000VE made by Sumitomo 3M Case: 10336-52F0-008 made by Sumitomo 3M Connector: HR10A-10P-12P made by Hirose Electric Connect to the FOCUS connector on lens.Cable length: At least 800 mm or so Connector: HR10A-10P-12P made by Hirose Electric Connect to the ZOOM...