Panasonic Hybrid Control Panel Aw Rp501 Operating Instructions

							-19-
• Changing Switch Settings on Pan/tilt Head 
qRemove the cover from the pan/tilt head.
* Be careful of the Tally Indicator wire.wShift the mounting direction switches (SW1, SW2) on
the pan/tilt head depending on whether the head is
suspended from the ceiling or mounted on the floor.
They are originally set for suspended installation.
* Do not shift SW3, which is originally set to  If SW3 is
shifted from the original position, no operations can be
controlled from the control panel.ePlace the cover back on the pan/tilt head.
* Be sure not to trap the wires.
• If the pan/tilt head is connected to the control panel
with a cable longer than 300 meters, set the cable
compensation switch on the pan/tilt head to the ON
position in advance.  If the distance between the
pan/tilt head and the control panel is shorter than 300
meters, keep the switch in the original position (OFF).
For details on shifting the switch, refer to the figure
below or the Operating Instructions for Pan/tilt Head.
SW 2 SW 1 SW 3
SW 2 SW 1 DESKTOP
 
HANGING
Tally Indicator 
						

							-20-
• Shifting Cable Compensation Switch on Pan/tilt
Head
If the distance from the control panel to the pan/tilt head
is longer than 300 meters, set the cable compensation
switch to the ON position by observing the following
procedure.
qRemove the controller connection panel from the
pan/tilt head.
* Be careful of the wires.
wShift the cable compensation switch on the inner side
of the controller connection panel of the pan/tilt head to
the ON position.
ePlace the controller connection panel back on the
pan/tilt head.
ON
OFF
n Lens Mounting• Turn the lens lock ring knob fully counterclockwise.
• If the lens mount has a cap, remove the cap.
• With the lens positioning pin up, mount the lens.
• Turn the lens lock ring knob clockwise till the lens is
securely fastened.
Lens lock ring knob 
						

							-21-
CONNECTIONS• Before making any connection, switch off all the com-
ponents of the system.
• Use the control panel AC Adaptor AW-PS301 (optional)
and Pan/tilt Head AC Adaptor AW-PS300 (optional).
• Use the pan/tilt AW-PH300 and the Color Video
Camera WV-E550 or AW-E560.  To connect the pan/tilt
head to the camera, the Camera Cable AW-CA20T15
(optional) is necessary.
• Locally purchase a DC cable with a nominal cross sec-
tion of 1.25 mm
2or larger that meets the UL specifica-
tions, and connect the Pan/tilt Head AW-PH300 to the
Pan/tilt Head AC Adaptor AW-PS300 with that cable.
The maximum distance between the pan/tilt head and
pan/tilt head AC adapter is 30 m.
• Connect the AC Adaptor AW-PS301 to the control
panel and clamp the DC cable of the AC adaptor to the
cord clamp on the control panel.
• Connect the Pan/tilt Head AW-PH300 to the Color
Video Camera WV-E550 or WV-E560 with the Camera
Cable AW-CA20T15.
DC Cord Cord Clamper
Control Panel
AC Adaptor
AW-PS301 
						

							-22-
ITEM(AWC) UP(ABC)PAGEDOWN
  (BAR)IRIS
G/L  INVIDEO  OUT
ZOOM/FOCUS
REMOTEVD
VIDEO/RGB VBS/HD
    75ON
OFF
CONTROL
EXT DC INSEE MANUALCAUTION
• Connect the iris control cable of the motor-driven zoom
lens to the camera and the remote (zoom/focus control)
cable to the pan/tilt head.  If the remote (zoom/focus
control) cable of the motor-driven zoom lens is con-
nected to the camera, the lens cannot be controlled.• Connect the control panel to the pan/tilt head with the
three coaxial cables (video signal, G/L signal, camera
control signal)  and one 10BASE-T straight cable
(pan/tilt head control signal).  The maximum distance
between the control panel and pan/tilt head is 500
meters for coaxial cables 5C-2V and 10BASE-T cable
(UTP category 5 or equivalent).
• For further details on connecting the individual devices,
refer to their operating instruction manuals.
To Lens Interface ConnectorTo Iris Connector Iris Control
Cable Remote (Zoom/Focus
Control) Cable 
						

							-23-
AC IN
LAMP AC OUT
MIN  250W
MAX 500W
OPTION   SW
CONTROL OUTOPTION   SW
CONTROL INLAMP
CONTROL
OP SC
DC 15V
OUT- +
TALLY
HOT DC12V IN
AUX  CONTROL  IN
VIDEO  IN OUT G/L  OUTVIDEO OUT 1 VIDEO OUT 2
CONTROL CONTROL  OUTPAN/TILT CAMERA
TO CAMERA PAN/TILT HEADG / L  IN
S-VIDEO OUT
PAGEITEM(AWC) UP(ABC)DOWN  (BAR)
IRIS
G/L  IN
VIDEO  OUT
ZOOM/FOCUS
REMOTEVD
VIDEO/RGB VBS/HD
    75
ON
OFF
CONTROL
EXT DC INSEE MANUAL
CAUTION
Connecting the control panel to Color Video Camera
(WV-E550 or WV-E560), Pan/tilt Head (AW-PH300), and
Pan/tilt Head AC Adapter (AW-PS300)
Pan/tilt Head
AW-PH300Color Video Camera
WV-E550 or AW-E560To Servo Control Zoom Lens
Camera Cable
AW-CA20T15
AW-RP501
Pan/tilt Head AC Adaptor AW-PS300VIDEO OUT
G/L THROUGH
OUT
G/L IN
PAN/TILT CONTROL IRIS CONTROL
ZOOM/FOCUS
CONTROL
CAMERA CONTROL
GEN-LOCK
VIDEO
DC+15VS-VIDEO OUT 
						

							-24-
SPEED FOUCUS PA N  /  T I LT
ZOOM
TELE
WIDEFA R
LEFT RIGHTUP
DOWN
NEAR
DEFON
OFF
POWEROPERATE
IRIS
BAR
CAMMODEGAIN AWC
SCENE
FILEABC
AT W
A
B
AUTO/AIWELC LOW MID
MANUON SC H
OFF HIGH AGC
OFF 1 / 100SHUTTER
ON
OFF
LAMPMEMORY
ON
OFF AUTO
MANUON
OFFON
OFFON
OFF ON
OFFON
OFF
WIP
EXT ND OPH / F
1 .
2 .
3 .
4 .
G/L PHASE
PRESET
T.PED
CABLE COMPHybrid Control Panel AW-RP501
2 1345
67891090¡  180¡
0¡       270¡
LEVELTALLY
YC
S-VIDEO
VIDEO
VIDEO
G/L 
G/L
DC 15V
OPTION SWITCH
CONTROL
CONTACT
POWERON
OFF
Color  Monitor  WV-CM   1470
PUSH
SYSTEM TALLY
CAMERA CONTROL
PAN/TILT CONTROL ZOOM/FOCUS CONTROL
IRIS CONTROL
LAMP
CONTROL
• Example of System Connection
Camera Cable
AW-CA20T15 Color Video Camera
WV-E550 or AW-E560
Pan/tilt Head AC Adaptor
AW-PS300
Hybrid Control Panel AW-RP501Signal Generator
Control Panel
AC Adaptor
AW-PS301 Halogen LampServo Control
Zoom LensColor Monitor
(75Wtermination) Be sure to connect the zoom/focus control
to the pan/tilt head, not to the camera
Unnecessary if no
halogen lamp is used. Unnecessary if
no optional unit
is connected.
Optional Units
Special Effect Generator and
Switcher etc. 
						

							-25-
OPERATING PROCEDURES1.Power
Set the power switch on the pan/tilt head AC adapter to
the ON position, then set Power ON/OFF Switch won
the control panel to the ON position.
2. Pan/tilt Limiter Setting for Pan/tilt Head
If there are obstacles around the pan/tilt head, set the
limiters to limit the operating range (pan left and right
ends, tilt up and down ends) of the pan/tilt head.
Note:The switches on the pan/tilt head have been pre-
set before shipment from the factory on the
assumption that the pan/tilt head would be sus-
pended from the ceiling.  If the pan/tilt head is
mounted on a board, for example, be sure to shift
the mounting direction switches on the pan/tilt
head.  Unless this is done, pan/tilt directions will be
reversed and pan/head operation limiter data can-
not be properly stored in the memory.  For details
on shifting these switches, refer to INSTALLATION
OF PAN/TILT HEAD at page 18 or the Operating
Instructions for Pan/tilt Head.
MEMORY
PRESET
2 1345
678910
qLeft Panning Limiter
Turn the pan/tilt head to the desired left panning limit
with PAN/TILT Lever #8, keep MEMORY Switch @7
depressed, and simultaneously press buttons [1] and
[6] of PRESET Switches @8for 5 seconds or more.
When the desired limit has been set, button [5] of PRE-
SET Switches @8lights.
To reset the limit, keep the MEMORY switch @7
depressed, and simultaneously press buttons [1] and
[6] of PRESET Switches @8again for 5 seconds or
more.  When the set limit is reset, button [10] of PRE-
SET Switches @8lights.
Up tilting limiterPreset position selection switch
Left panning
limiterLights on
completion
of setting.
Preset
memory
switchLights on 
completion 
of resetting
Down tilting limiterRight panning 
limiter 
						

							-26-
wRight Panning Limiter
Turn the pan/tilt head to the desired right panning limit
with PAN/TILT Lever #8, keep MEMORY Switch @7
depressed, and simultaneously press buttons [4] and
[9] of PRESET Switches @8for 5 seconds or more.
When the desired limit has been set, button [5] of PRE-
SET Switches @8lights.
To reset the limit, keep the MEMORY Switch @7
depressed, and simultaneously press buttons [4] and
[9] of PRESET Switches @8again for 5 seconds or
more.  When the set limit is reset, button [10] of PRE-
SET Switches @8lights.
eUp Tilting Limiter
Turn the pan/tilt head to the desired up tilting limit with
PAN/TILT Lever #8, keep MEMORY Switch @7
depressed, and simultaneously press buttons [2] and
[3] of PRESET Switches @8for 5 seconds or more.
When the desired limit has been set, button [5] of PRE-
SET Switches @8lights.
To reset the limit, keep the MEMORY switch @7
depressed, and simultaneously press buttons [2] and
[3] of PRESET Switches @8again for 5 seconds or
more.  When the set limit is reset, button [10] of PRE-
SET Switches @8lights.rDown Tilting Limiter
Turn the pan/tilt head to the desired down tilting limit
with PAN/TILT Lever #8, keep MEMORY Switch @7
depressed, and simultaneously press buttons [7] and
[8] of PRESET Switches @8for 5 seconds or more.
When the desired limit has been set, button [5] of PRE-
SET Switches @8lights.
To reset the limit, keep the MEMORY switch @7
depressed, and simultaneously press buttons [7] and
[8] of PRESET Switches @8again for 5 seconds or
more.  When the set limit is reset, button [10] of PRE-
SET Switches @8lights. 
						

							-27-
3. Cable Compensation Setting, Genlock and
Total Pedestal Adjustment• Cable Compensation
Signal degradation due to cable length between the con-
trol panel and the pan/tilt head can be compensated for.
qIf the cable length from the pan/tilt head to the control
panel is longer than 300 meters, set the cable com-
pensation switch on the pan/tilt head to the ON posi-
tion.  For details, refer to INSTALLATION OF PAN/TILT
HEAD at page 18 or the Operating Instructions for
Pan/tilt Head.
wConnect a waveform monitor or a vectorscope to the
VIDEO OUT connector $7on the control panel, set the
MODE BAR/CAM Switch rto the BAR position, then
observe the color bar signals.
eAdjust the Y (luminance) signal level with CABLE
COMP Y Control @0. then adjust the C (chrominance)
signal level with CABLE COMP C Control @1.  Repeat
this until the video output of the control panel is adjust-
ed as shown in the figure below.
Note:Turning CABLE COMP Y Control @0changes not
only the Y (luminance) signal level but also the
video signal levels as a whole.
GRAY
YELLOW
CYAN
GREEN
MAGENTA
RED
BLUE
100
  90
  80
  70
  60
  50
  40
  30
  20
  10
    0
–10
–20
–30
–40+69 +77
+56
+48
+38
+12
+7
–5
–16 –16+15 +28 +36
+20
–20 +20
–20+100 +100
+89
+77
+72
+46 IRE
75%
100%
1V[p-p]
+100
+27
+27
-20
–13 –13
100
  90
  80
  70
  60
  50
  40
  30
  20
  10
    0
–10
–20
–30
–40IRE
75%
100%
+20
–20+20
–20 +7.5 +7.5
-I   WHITE  +Q       BLACK
1V[p-p]
Color Monitor
Color MonitorWaveform Monitor
Waveform Monitor 
						

							-28-
• Genlock AdjustmentTo use the camera in external sync mode, phase adjust-
ment is necessary to match the phases with those of the
other units and camera.  No G/L adjustment is necessary in
case of no genlock.
• Horizontal Phase Adjustment
qSet G/L PHASE ON/OFF Switch !5to the ON position.
Note:When G/L PHASE ON/OFF Switch !5is set to the
ON position, the sync phase of the camera
changes to the settings of G/L PHASE H Control
!8, G/L PHASE Coarse Switch !6, and G/L PHASE
SC Control !7.  Unless G/L phase adjustment is
necessary, do not set G/L PHASE ON/OFF Switch
!5to the ON position.
wObserve the waveforms of the G/L signal input (black
burst signal) and video signal output on a dual channel
oscilloscope, and turn the G/L PHASE H control !8tomatch the horizontal phase as shown in the figure right.
eSet G/L PHASE ON/OFF Switch !5back to the OFF
position.
ON SC H
OFF
G/L PHASE
90° 180°
0°      270°
External genlock
input signal
(black burst
signel)
Video signal
G/L PHASE H Control
G/L PHASE
ON/OFF Switch
Waveform Monitor
Vector ScopeColor Monitor
(75Wtermination)