Panasonic Household Massae Lounger Ep30007 Operating Instructions

							 8
11  Massage Area Display
Flashes to indicate areas 
currently being massaged
In the Massage Area Display, 
positions are estimated. 
Therefore, there may be some 
differences between the actual 
sensation and the display.
12
  Back Intensity/Speed Display
Intensity and speed of the 
massage heads are displayed.
The speed is displayed only in the 
manual operation.
13
  Manual Upper Body Complex 
Operation Display
Indicates optional operations 
added to manual upper body 
operation
See page 25
TAP 1
TAP 2
AUTO WIDTH REGIONAL ROLL
•
•
•
•
•
•
1
 
Voice Guidance Volume Display
See page 37
Off
Soft
Medium Loud
2
  Time Remaining Display
(During massage)
(After finishing massage)
3 Ultra Knead/Repeat Display
See page 27
(Ultra knead)
(Repeat)
4  User Memory Display
Illuminated when operating the 
User Memory function
See page 39 to 41
•
•
•
• 5
 
Pressure Display
Displays the pressure applied by 
the massage heads
6 Massage Style Display
Displays the current massage 
style
Thumb-like action
Palm-like action
Fist-like action
7  Self-Program Setting Display
See page 22 to 23
8
  Manual Upper Body Massage 
Display
See page 24 to 26
9
  Air Intensity Display
See page 30
10
  Stretch Display
Indicates whether the leg stretch 
or the arm is on or off
On: Turned on
Off: Turned off
In operation: flashing
•
•
•
•
•
•
Display
* This illustration simulates when all lights are illuminated. 
						

							9
Setting up the massage lounger
1Where to use the unit
Ensure there is adequate space to recline.
Caution
Do not use the unit in areas with high humidity, 
such as the bathroom, because this can lead to 
electric shock or other accidents.
Place the unit on a totally flat surface. 
Failure to do so may result in the unit tipping over.
•
•
Do not expose the massage lounger to direct sunlight or high 
temperatures, such as in front of a heater, etc., as this can cause 
discoloration or hardening of the synthetic leather.
Place the unit on a mat to prevent floor damage.
When placing a mat under the unit, the size of the mat should be 
sufficient (at least 47 × 28 in.  (120 × 70 

cm)) to cover the areas 
where the unit touches and where the legrest could touch the 
floor, as shown in the diagram on the right.
Install the unit near a power outlet.
•
•
•
•
Keep at least 4" (10 cm) away from the wall.
Approx. 77" (195 cm)
Width approx. 33" (84 cm)
Approx. 12" (30 cm)
Approx. 14"  
(35 cm)
Mat
Area where legrest 
could touc
h the floor Area where unit 
touches the floor
2Removing everything from the box and installing the unit
Use care to prevent lower back and other injuries that could occur when lifting this heavy object (approx. 176 bs. (80 kg)). 
(The unit must be carried by two persons.)
When using the wheels to move the unit, place a mat on the floor to protect the floor surface.
To put the unit down on the floor
Put the unit down slowly and carefully watch your step.
Put down the legrest by holding it with your hands until it has been set on the floor completely. If you release your hands 
before the legrest is fully extended, the legrest will forcefully return to the initial position.
•
•
•
•
Fabric Section
Groove
Hold the cloth 
section on the 
underside
Mat
Legrest Back cover Place your 
fingers in the 
groove 
						

							 10
Confirm that the main unit and the accessories are in the box.
Main unit
Accessories
• Armrests (Right/Left)
Left/Right indication
Air plug
Small holes on the inside fabric are an intentional 
part of the functional design.• Pillow• Control Panel Stand
Fixing screw
Control panel 
holder
Clip
• Control Panel Stand Covers
• Attachment Screws (M6 × 16) — 7
• Allen Key — 1(Cross-section)0.2" 
(4 mm)• Shoulder Plates• Sole Reflexology Plates
This is installed on the sole 
massage section prior to leaving 
the factory.
Operating Instructions
Child Safety Instructions (Yellow brochure)
How to transport and move (Yellow brochure)
Notes for body scanning (Pink brochure)
Quick Start Manual
•
•
•
•
•
Documents including the Operating Instructions
Width: Approx. 27" (68 cm)
Height: Approx. 26" (66 cm)
Length: Approx. 63" (160 cm)
• Lock Switch Keys — 2 One of the lock switch keys has been inserted 
in the lock switch prior to leaving the factory.
The other lock switch key is a spare to be 
stored for safekeeping out of the reach of 
children.
Do not remove this tag. 
						

							11
1Attaching the 
armrests
 (On both the right and left 
sides)
1. Insert the armrest into the 
unit.
Be careful to a v

oid pinching 
your fingers.
•
Assembly
2.
 Fasten the armrest with the 
attachment screws.
Set the two attachment 
screws in place by hand 
first and then tighten 
firmly with the allen key.
Use this Screw
Attachment Screw (M6 × 
16)
  × 4
Make sure that the seat 
surface is not damaged.
2Connecting the air plugs
(On both the right and left sides)
Insert the air plugs into the unit.
Push on the air 
plugs until you hear 
it click into place.
Air plug
Groove Armrest
(1)   Align the 
position
Main unit
Pipe
Right/Left 
indication
(2)  
Fasten the armrest with 
the attac
 hment screws.
Attachment 
Screw
Allen keyAttachment 
Screw
OutsideInside
Turn screws 
clockwise to  tighten. 
						

							 12
3Attaching the control panel stand to the right or left side panel of the unit
(Diagram shows attachment to right armrest.)
The position of the control panel when seated can be 
selected by choosing the appropriate hole for the screw.
NearApprox.  
20˚
Far
4Attaching the control panel stand covers
(On both the right and left sides)
The method for attaching the covers is the same for both sides. 
The diagram shows the side where the control panel stand is 
attached.
1. Inser
t the top tabs on the co ver into the bottom 
notc

hes on the armrest. 2.
 Insert the bottom tabs into the notc hes on the 
armrest.
1.
 Insert the attac hment scre

w into the lower hole first 
and then tighten lightly by hand.
2.  Securing the stand with the attachment scre ws.
Tighten the tw

o screws for the remaining two holes 
lightly by hand and then tighten firmly with the allen key. 
2
Control panel stand
1   Insert the attachment 
screw in either hole and 
then tighten.
Attachment screw Allen key
Use this screw
Attachment Screw (M6 × 16)
 × 3
Cover for Side WITH 
Control Panel Stand Cover for Side WITHOUT 
Control Panel Stand
Notches
Top tabs Control panel 
stand cover
NotchesBottom tabs
Push the cover until 
you hear it click.
Control panel 
stand
Allen key
Allen key
Control panel stand
Attachment screw
Attachment screw
Hole
Hole
To attach the control panel stand using the attachment 
screws, tighten the screws level with the holes as 
shown in the figure below.
If the screws are tightened at an angle, the hole may 
become deformed and the screws may become stuck in 
the middle.
Tighten the screws 
level with the holes. Do not tighten the 
screw at an angle 
with the hole. 
						

							13
When removing the control panel stand cover
1. Insert the head of a flat-tip screwdriver in the gap 
under the mark (O).
2.  Push the bottom tab of the cover up to lift the co ver

.
3.  Perform the same procedures as 1 and 2 above for 
the other gap.
4.  Pull the co
ver up diagonall

y.
Performing this procedure with the allen key or a 
Phillips screwdriver could damage the unit.
•
5Raising the backrest to the 
upright position
1.
 Insert the power plug into the power outlet.
2.  Confirm the key lock is set to the “open” 
position.
3.  Confirm the power s witc

h is set to the “on” 
position.
4.  Press the 
 button on the control panel 
twice.
The backrest will rise to the upright position 
automatically.
Flat-tip 
screwdriver
(Not included in 
the standard 
configuration)
Gap
1 22 
						

							 14
Moving the control panel cord to the left side (when control panel stand is on left 
side)
1. Press the  button on the control panel to turn on the power.
2.  Press the 
 button on the control panel and hold until the legrest 
has risen far as it will go.
Continue pressing until a “beep-beep-beep” sound is heard.
3.  Remove the contr ol panel cor

d from the cord-holder groove.
4.  Move the control panel cord under the legrest to the left side.
5.  Fasten the control panel cord at two points in the cord-holder groove.
6Placing the control panel into the 
control panel stand
1.  Fit the groove on the side of the control panel to the 
projection on the inside of the holder.
Legrest
Cord-Holder Groove
Control Panel Cord
Push in
Control Panel Cord
Backside of the 
control panel
Projection on the 
inside of the holder
Groove on the control panel 
						

							15
8Attaching the pillow
1. Attach the pillow to the velcro fasteners.
See page 38 for a guide to the position of the pillow
Pillow
Velcro 
fasteners
•
2.
 Fasten the contr ol panel cor
 d using the clip.
Clip
Control panel cord Fasten the cord so that the 
portion under the clip is 
not slack. Lift the control panel to remove.
1.
 Insert the plate into the pocket on the outer shoulder 
massage unit.
Grasp the pocket and pull it slightly to expand the 
opening, so that the plate can be inserted easily.
Shoulder plate
Pocket
•
(For the right 
shoulder) (For the left 
shoulder)
2.
 Slide the inserted plate f or the outer shoulder to the 
inside (recommended position). The up/do

wn and in/out positions of the plate can be 
adjusted. 
The recommended position is when the plate is 
inserted into the deepest position and then moved to 
the most inside position.
Grasp the pocket opening with one hand, hold the plate 
with the other hand, and move it into the deepest 
position.
•
•
7Inserting the shoulder plate
Proper plate for each outer shoulder 
						

							 16
Before sitting down
Check the following before using the unit
1Check the surrounding area
Make sure there are no objects, people, or pets in the vicinity of the unit.
2Check the power cord and the power plug
Warning
Remove dust from the power plug periodically. 
Failure to observe this precaution may result in 
defective insulation of the cord due to moisture. 
Clean dust from the cord using a dry cloth.
Do not damage the power cord and the power 
plug. 
(Do not damage, expose to heat sources, bend, 
twist, pull forcibly, bundle or place heavy objects 
on the cord.) 
Using a damaged power cord and/or the power plug 
may result in electric shocks, short circuits, or fires. 
Ask your sales dealer to repair the power cord and/or 
the power plug, or contact a customer service center.
•
•
3Switching on the power supply
1.
 Insert the power plug into an electrical outlet.
2.  Turn the lock switch key to the “open” position.
3.  Slide the power switch to the “on” position.
Warning
Insert the power plug firmly until it stops 
completely. 
Failure to observe this precaution may result in 
electric shocks or fires due to heat generation.
Do not exceed the rated values of the plug and the 
wiring or use any voltage other than the rated 
voltage. (The unit cannot be used abroad or used 
with a transformer.) 
Failure to observe this precaution may result in 
electric shocks, malfunctioning or fires due to heat 
generation.
Do not handle the power plug with wet hands. 
Doing so may result in electric shocks.
•
•
•
4Check the unit
1.
 Make sure there are no tears or rips in the fabric.
Warning
Lift the back cushion and make sure the fabric on 
the backrest is not torn. (Even if it is torn very 
slightly, stop using the unit immediately, remove 
the power plug, and request repairs.) 
Using the unit with the fabric torn may result in injury 
or electric shocks.
• Check
Fabric
Check
Backrest
Back cushion 
						

							17
3. Make sure the massage heads are in the retracted position.
Caution
Sit on the unit after confirming the massage 
heads are in the retracted position. 
Failure to observe this precaution may result in 
accident or injury.
•
When the massage heads are not in the retracted position Press the 
 button twice to return the massage heads to the 
retracted position.
4.  Make sure the legrest is in the fully lo wered position.
Caution
Do not stand on the legrest or place any object on 
it when the legrest is not in the fully lowered 
position. 
Failure to observe this precaution may result in 
accident or injury from the foot part of the legrest 
turning or the unit tipping over.
•
To lower the legrest
Make sure the legrest has fully returned to the original position by pulling the legrest slide lever, and then press the  
button twice.
2.  Make sure there is no foreign objects on 
the chair.
Caution
Sit on the unit after confirming there is 
no foreign matter between the parts of 
the unit. (Check for foreign objects on 
the backrest, leg/sole massage section, 
hand/arm massage section, seat/thigh 
side massage section, or the outer 
shoulder massage section.) 
Failure to observe this precaution may result 
in accident or injury.
•
Outer shoulder massage 
section
Hand/Arm 
massage section
Seat/Thigh side 
massage section
Leg/Sole massage  section
3. Retracted position
Legrest 
slide lever
4. Check