Panasonic Home Theater Audio System Sc Ht56 Operating Instructions

							11
RQTX0175
TRA N SMITTERDIGITALPUSHPUSH
2
3
1
1
2
AC IN~
AC IN~
Auto speaker setup
STEP 4
Auto speaker setup
Auto speaker setup allows you to achieve a satisfactory listening environment easily with the use of the supplied calibration microphone 
as a detector of sound signals. The unit will first perform automatic speaker detection, then checks and adjusts the following settings.
Process for auto speaker setup
Loud test tones are output from the speakers during setup, so keep children out of the room.
Checks which speakers you have connected.
•
DETECTION
DISTANCE Chec
 ks the distance of each speaker from the listening position and adjusts the 
timing of each channel automatically.
•
Connect the calibration 
microphone to the 
[SETUP MIC] jack on 
the front panel.
Note
The calibration microphone is sensitive to 
heat. Keep it away from direct sunlight and 
do not place it on top of the unit.
Placing of calibration 
microphone. P
 lace on a flat surface at the seating area.
Set calibration microphone position at 
your ear height.
•
•
Turn on the unit.
Press 
       .
The standby indicator goes off when you turn on the unit.
•


Calibration microphone 
(included)
Bef
ore setup
Conduct the auto speaker setup in a quiet environment. A noisy background will give unsatisfactory results. Mak
 es any further corrections to the frequency response.
•
FREQUENCY
LEVEL Chec
 ks and adjusts each speaker level automatically.
•
Turn off all components before making any connections.
Peripheral equipment and cables sold separately 
unless otherwise indicated.
To connect equipment, refer to the appropriate 
operating instructions.
•
•
•
SC-HT56P_MP (RQTX0175-2P).indb   119/19/2008   12:28:24 PM 
						

							12
RQTX0175
a) Press and hold  .[
AUTO SPEAKER SETUP] indicator starts flashing.
“AUTO SETUP” appears on the display.
b) The unit checks that you have correctly   connected the calibration micr

ophone.
c) The automatic setup starts with STEP 1, STEP 2,   and STEP 3 calibration as f

ollows.
STEP1 – DETECTION/DISTANCE   STEP2 – FREQUENCY 
 STEP3 – LEVEL
For y

our reference
Loud test tones are output from each speaker during the configuration.
During setup, operations may stop when there is an error message on the display. 
Refer below for troubleshooting.
•
•
•
•
STEP 4
Auto speaker setup
To cancel during setup 
Message
SolutionsPages
“INSERT MIC” Calibr
 ation microphone is not detected. Insert the microphone correctly.
• 11
“CHECK CONNECTION 
TO 
LS/RS SPEAKERS” One of the surround speak
 ers is not detected. Check the connections.
• 6
“CHECK CONNECTION 
TO 
L/R SPEAKERS” Chec
 k the front (L) and (R) connections.
• 6
Troubleshooting for auto speaker setup
While performing auto speaker setup, errors may occur and the messages will blink or scroll on the display, depending on the 
conditions. Press any button on the main unit or remote control to stop the setup.
 
After troub

leshooting, press and hold   to start the setup process again. 
Auto speaker setup may produce an unsatisfactory result with some speaker setups and configurations.
Auto speaker setup will not start if you have muted the speakers. Turn the muting off ( ➡ page 19).
  
Auto speaker setup will not start if you have plugged in headphone. Unplug any headphone.
VIERA Link “HDAVI Control
TM” ( ➡ page 8) is disab led during auto speaker setup.
•
•
•
•
Note
Press any button on the main unit or remote control. “CANCELED” appears on the display. “COMPLETE” appears on the display and all calibrations are saved.
[A

UTO SPEAKER SETUP] indicator lights. 
T

o exit, press and hold  .
Disconnect the calibr

ation microphone.
•
•
•
•
-AUTO SETUP
AUTO
SPEAKER SETUP AUTO
SPEAKER SETUP
Auto speaker setup finishes.
Start performing auto 
speaker setup.
Auto speaker setup
Perform  auto  speaker  setup  again  if  you  have  changed  the  speakers,  speaker  positions,  or  the  layout  of  your  listening 
environment.
If 
you find speaker output unsatisfactory, reset all auto speaker setup settings and change them manually. Refer to “Auto setup” 
( ➡  page 13).
The calibration will give optimal result for “DISTANCE”. Theref
 ore, you are unable to adjust the setting manually.
•
•
•
Note Turn off all components before making any connections.
Peripheral equipment and cables sold separately 
unless otherwise indicated.
To connect equipment, refer to the appropriate 
operating instructions.
•
•
•
-AUTO SETUP
-AUTO SETUP
SC-HT56P_MP (RQTX0175-2P).indb   129/19/2008   12:28:28 PM 
						

							13
RQTX0175
Settings
2aSelect and press [ENTER].
R efer to pages 13 and 14 for each item settings.
For “REMOTE”, refer to page 21.
For “RESET”, refer to page 19.
•
•
•
2b
Select and press [ENTER]. P r e s s   r e p e a t e d l y 
until “EXIT” appears.
Press and hold.
DISTANCE  ↔ AUTO SETUP 
↔ INPUT 
MODE  ↔ HDMI 
↔ DRCOMP 
↔ 
ATTENUATOR  ↔ REMOTE 
↔ TV DELAY 
↔ 
RESET  ↔ EXIT
Enter the 
setup mode. 1 Select the item you want to change.2 Change the 
setting.3Exit the 
setup mode.4
Press  [ENTER]  to 
completely  exit  the 
setup mode.
Press 

to change the 
setting.
Press once to enter.
A

uto speaker setup calibration will give optimal result for “DISTANCE”. Therefore, you are unable to adjust the setting manually.
Note
Change the settings to suit your equipment 
to the environment in which you are using 
it. Before making any changes, read the 
descriptions of the settings, note the factory 
settings and ranges, and refer to the 
equipment's instructions.
Settings
Change  the  distance  so  that  the  sound  from  all  the  speakers  (except  for  the 
subwoofer) reaches you at the same time.
You can select distances between 3 feet and 30 feet.
The factory settings are: 10 ft (feet)
10 ft (feet)
5 ft (feet)
LR (front): 
C (center):
S (surround):
Enter 

the distance of the front, center and surround speakers from 
the seating position.
•
Distance
YES: Reset all auto speaker setup settings
NO: To cancel (factory setting)
Auto setupReset the settings done in auto speaker setup.
•
(continue on next page)
DISTANCE LR3 feet to 
30 feet
C
S
A

UTO SETUP DEFAULT NO YES
INPUT MODE TV AUTO
ANALOG
DIG
PCMFIX
DVR
DVD
32a2b
Repeat for each speaker channel
1 In  rare  cases,  the  unit  may  have  trouble  recognizing  PCM  signals  and  this  may  cause  the  beginning  of  tracks  to  be  cut  off. 
Select “PCMFIX” if this occurs.
With DTS, the signals may not be recognized at all. Engage the DTS FIX mode if this occurs.
To engage the DTS FIX mode:
Press and hold [-MENU] and [ENTER] at the same time. “DTS” lights.
To cancel the DTS FIX mode:
Press and hold [-MENU] and [ENTER] at the same time.
The mode cancels when input mode is set to AUTO or when the unit is turned off.
W
 hen  a  FIX  mode  is  on,  the  unit  cannot  process  other  signals.  This  may  cause  noise  to  be  output.  If  this  occurs,  select  an 
input mode other than PCMFIX, or cancel the DTS FIX mode.
•
Note
AUTO: The unit automatically detects whether input is digital or analog.
        (factory setting)
ANALOG: Select to make the unit accept analog input.
DIG: Select to make the unit accept digital input.
PCMFIX
1: Select to input to PCM. T his  unit  automatically  detects  whether  input  is  digital  or 
analog, but you can fix the input mode.
•
Input mode
Display
Switch on.
SC-HT56P_MP (RQTX0175-2P).indb   139/19/2008   12:28:32 PM 
						

							14
RQTX0175
Settings
Output the signal. Adjust the main volume.Select the speaker 
channel. Adjust the level. Stop the test 
signal.
VOL
C    +4dBPress and hold.
Repeat for each speaker channel
C (center), RS (surround right) and LS (surround left) can be adjusted between -6 dB and 
+6  dB,  with  0  dB  being  the  level  of  the  front  speakers.  Adjust  center  and  surround  output  to 
the same apparent level of the front speakers.
F
 or  SUBW  (subwoofer),  you  can  select  “SUBW  OFF”  so  there  is  no  output,  “SUBW  MIN” 
for  minimum  output,  a  level  between  1  and  19,  or  “SUBW  MAX”  for  maximum  output.  Adjust 
subwoofer output so it is balanced with the front speakers.
Press and hold.
L    C    R    RS    LS    SUBW
TEST     L
VOL
(A/D Attenuator)
Turn  the  A/D  attenuator  on  if  “OVERFLOW”  lights  frequently 
when using 2-channel analog input. The factory setting is OFF.
•
DRCOMP(Dynamic range compression)
Change  this  setting  to  listen  to  software  recorded  with  Dolby 
Digital  at  low  volume  (such  as  late  at  night)  and  maintain  audio 
clarity.  It  reduces  the  peak  level  in  loud  scenes  without  affecting 
the sound field.
•
OFF: The software is played with the original dynamic range (factory setting).
STANDARD: The level recommended by the producer of the software for household   
  
        viewing.
MAX: The maximum allowable compression (recommended for night viewing).
Attenuator
TV delayDelay audio if there appears to be a difference in timing between 
audio and pictures. The factory setting is ON.
•
To reduce standby power consumption.
Choice for turning off the VIERA Link “HDAVI ControlTM” 
( ➡  page 8).
•
•HDMI settings
Standby selection
OFF: Standby power consumption reduced  
  (approximately 0.3 W).
S

ignals  from  DVD  equipment  cannot  pass 
through  HDMI  connection  to  the  television 
when the unit is in standby ( ➡ page 8).
V

IERA  Link  “HDAVI  Control”  ( ➡ 
 page  8) 
does not work when the unit is in standby.
O
N :  No rma l  st an db y  po wer   c on su mpt io n 
(factory setting)
•
•
VIERA Link “HDAVI Control”
OFF: VIERA Link “HDAVI Control”  
  is OFF
ON: VIERA Link “HDAVI Control”   is ON (factory setting)
HDMI STNBY
OFF
ON
CTRL
DRCOMP OFF STANDARD
MAX
ATTENUATOR OFF ON
TV DELAY OFF ON
32a2b
Adjusting speaker output levelSettings
Display
Switch on.
SC-HT56P_MP (RQTX0175-2P).indb   149/19/2008   12:28:35 PM 
						

							15
RQTX0175
Basic operations
TUNER FMTV
TUNER AM
BD/DVR
D

VD-P 
1234
Switch on.  Select input. Start play of the 
source.The unit sets the sound 
mode  to  suit  the  input 
signal.
Adjust the 
volume. 
PL
MOVIE
Use  this  mode  when  playing  movie  software  recorded  in  Dolby 
Surround.
MUSIC
Adds surround effects to stereo sources.
PANORAMA
S

ound  is  spread  out  more  so  you  feel  like  you  are  surrounded  by 
music.
LIVE
Brings  you  up  close  for  “live”  stage  performance  and  smoother 
vocals.
POP/ROCK
For pop, rock, and other music that has a punch to it. 
VOCAL
For adding gloss to vocals. 
JAZZ
Conveys the exciting and intimate atmosphere of a jazz club.
DANCE
For dance music and other sounds with a strong beat.
PARTY
This 

mode uses the front and surround speakers so that sound is in 
stereo regardless of the direction you are facing.
DRAMA
For dramas and other material where dialog is important.
ACTION
For action movies and other material where impact is important. 
SPORTS
To make you feel like you were in the stadium. 
MUSICAL
For musicals and other material where music is important. 
GAME
Enjoy gaming with more impact.
MONO
For monaural sound.
Press           to select a mode from the table at 
right.
To cancel, press [OFF].
You 
 can make fine surround settings when in the 
MUSIC or PANORAMA mode. ( ➡ page 18)
•
Adding surround effects to stereo sources
Using Dolby Pro Logic 
ΙΙ
Dolby  Pro  Logic ΙΙ  processor  works  not  only  on 
sources  recorded  with  Dolby  Surround,  but  also 
on any stereo source.
Using the Sound Field Control (SFC)
E n j o y   a n   e n h a n c e d   s o u n d   e x p e r i e n c e   w i t h 
greater presence and spread by using these SFC 
modes with PCM or analog stereo sources.
Press                      to select a mode from the 
tables at right. To cancel, press [OFF].
You can change the speaker level of SFC.
( ➡  page 18)
•MUSIC
MOVIE
Note
Dolby  Pro  Logic 
ΙΙ  and  SFC  modes  remain  in 
effect until you turn the mode off.
When input is PCM with sampling frequencies 
of 96 kHz or 88.2 kHz, you cannot add 
surround effects with Dolby Pro Logic  ΙΙ or 
SFC.
W
 hen  input  is  Dolby  Digital  or  DTS,  you  can 
use SFC.
•
•
•
Basic operations
PL
SC-HT56P_MP (RQTX0175-2P).indb   159/19/2008   12:28:41 PM 
						

							16
RQTX0175
MENU operation
MENU operation
This  is  an  outline  of  the  operations  you  can  perform  with 
the MENU.
T U N E RF M   M O D E
M E M O RY
AU T O   M E M O
T U N E   M O D E
B E AT   P R O O FM O D E   1
M O D E   2
AU T OE X I T
E X I T
M O N O
M E M O     C H   1
M E M O     C H 3 0
S TA R T
C A N C E L
M A N U A L
P R E S E T
B A S S           0
T R E B L E       0
B A L A N C E
D I M M E R   O F FD I M M E R   O F F
D I M M E R           1
D I M M E R           2
D I M M E R           3
S L E E P     O F F
B A S S       - 6
B A S S       + 6
T R E B L E   - 6
T R E B L E   + 6
S L E E P     O F F
S L E E P       3 0
S L E E P       6 0
S L E E P       9 0
S L E E P     1 2 0
L R
2
1
345Main menu Sub menu 1 Sub menu 2 Exit
Press 
repeatedly 
until “EXIT” 
appears. Press 
[ENTER] to 
completely 
exit the 
m

enu mode.
Press [-MENU] once.
The radio  ➡ page 17
Press 
repeatedly 
until “EXIT” 
appears. Press 
[ENTER] to 
completely 
exit the 
m

enu mode.
(TUNER FM only)
Display
(TUNER AM only)
Adjust the bass  ➡ page 18
Adjust the treble  ➡ page 18
You 

can  adjust  the  balance  of 
the front speakers  ➡ page 18
D

i m   t h e   d i s p l a y   f o r   b e t t e r 
viewing in a darkened room 
➡  page 19
The 
 SLEEP timer can turn the 
unit off after a set time 
➡  page 19
SC-HT56P_MP (RQTX0175-2P).indb   169/19/2008   12:28:45 PM 
						

							17
RQTX0175
The radio
21
The radio
Press [INPUT SELECTOR < or >] 
to select “TUNER FM” or “TUNER 
AM”.Select the frequency.
Auto  tuning  starts  if  you  press  and 
hold the button. 
Direct tuning
Input the frequency of the station.Remote control
1.  Press [TUNER,  ―BAND] to select “TUNER”.
2.  Press and hold [TUNER , ―BAND] to select “TUNER 
FM” or “TUNER AM”.
3. 
Press [TUNER DIRECT TUNING].
4.  Press the numbered buttons to enter the  frequency.
e.g. To select 107.9 MHz, press [1]  → [0] 
→ [7] 
→ [9]
I
f  you  do  not  press  a  button  while  the  cursor  is  flashing,  the 
display returns to the frequency being received.
I
 f the frequency has not been input correctly, “ERROR” will be 
displayed.
•
•
Automatic presetting
The FM stations the unit can receive are preset in channels 1 to 
30. The AM stations the unit can receive are preset in channels 
21  to  30  (FM  stations  are  replaced  if  any  were  preset  in  these 
channels).
Preparation: Tune to either FM 87.9 MHz or AM 530 kHz.
Main unit
1.  Press [-MENU] to select “TUNER”  ➡ “AUTO 
MEMO”.
2. 
Press [TUNE  2 / - or 
1 / +] to select “START” 
➡  [ENTER].
  Select “CANCEL” to cancel.
T
he tuner presets all the stations it can receive into the channels 
in ascending order.
D

uring  automatic  presetting,  the  memory  indicator  (M)  flashes 
and  the  frequency  scrolls.  The  memory  indicator  and  channel 
numbers are displayed for a second when a station is preset.
T
 he  last  station  to  be  preset  is  displayed  when  presetting 
finishes.
1.  Press [-MENU] to select “TUNER”  ➡ “TUNE 
MODE”.
2. 
Press [TUNE  2 / - or 
1 / +] to select “PRESET” 
 ➡  [ENTER].  Select “MANUAL” to cancel.
3.  After exiting the menu:
  Press [TUNE 
2 / - or 
1 / +].
Manual presetting
Preset the stations one at a time.
Preparation: Tune to the station you want to preset.
Main unit
1.  Press [-MENU] to select “TUNER”  ➡ “MEMORY”.
2. 
Press [TUNE  2 / - or 
1 / +] to select the channel
 
 

➡  [ENTER].
  (“STORED” lights.)
For your reference
FM stations can also be preset in the MONO mode.
Selecting channels
Remote control
1.  Press [TUNER,
 ―BAND] to select “TUNER”.
2.  Press [SKIP  u, 
2 or  i , 
1].or
Press the numbered buttons.
For channels 1 to 9, press the corresponding number.
For channels 10 or over, press [
≧10], then the two digits.
e.g. To select channel 21: [
≧10]  → [2] 
→ [1]
Main unit
Y o u   c a n   i m p r o v e   F M   r e c e p t i o n   b y   s w i t c h i n g   r e c e p t i o n   t o 
monaural. Main unit
1.  Press [-MENU] to select “TUNER” ➡ “FM MODE”.
2.  Press [TUNE  2 / - or 
1 / +] to select “MONO” 
➡ [ENTER].  Select “AUTO” to cancel.
Reducing excessive noise
During FM stereo receptionDuring AM reception
When there is a lot of noise interference with an AM broadcast, 
try switching this mode.
1.  Press [-MENU] to select “TUNER” ➡ “BEAT 
PROOF”.
2.  Press [TUNE  2 / - or 
1 / +] to select “MODE 1” or 
 

“MODE 2” ➡ [ENTER].
Main unit
SC-HT56P_MP (RQTX0175-2P).indb   179/19/2008   12:28:47 PM 
						

							18
RQTX0175
Sound field
Adjusting SFC
You  can  adjust  the  sound  field  by  adjusting  the  level  of  the 
speakers. This adjustment can be made for each SFC mode 
(➡  page 15). 
1.  Press [-LEVEL, ―TEST] to select the speaker 
channel.
  Each time you press the button:
  C  → RS 
→ LS 
→ SUBW
2. 
Press [-] or [+] to adjust the level.
  C, RS, and LS: -6 dB to +6 dB
  SUBW: OFF  ↔ MIN 
↔ 1 - 19 
↔ MAX
Remote control
Center focus
Use  with  discs  where  the  dialogue  is  recorded  in  the  center 
channel.
Y
ou  can  make  the  sound  of  the  center  speaker  seem  like  it  is 
coming from within the television.
Press and hold [-EFFECT, ―C.FOCUS].
Remote control
“C.FOCUS” lights.
The factory setting is off.
You cannot use this when the sound mode is STEREO.
You 

can  adjust  the  effect  of  the  Dolby  Pro  Logic 
ΙΙ 
 MUSIC  and 
PANORAMA modes ( ➡ page 15).
You 
can  make  up  for  differences  in  the  output  level  of  the  front 
and surround speakers.
You 
 can  choose  a  level  between  -3  and  +3:  Increase  the  level 
to move sound to the front speakers, decrease to move it to the 
surround speakers.
The factory setting is 0.
1.  Press [-EFFECT, ―C.FOCUS] to select “DIMEN”.
2.  Press [-] or [+] to adjust the effect.
Remote control
Dimension Control “DIMEN”
You  can  adjust  the  effect  of  the  Dolby  Pro  Logic  ΙΙ  MUSIC  and 
PANORAMA modes ( ➡ page 15).
This 
adjustment  helps  you  realize  a  more  natural  sound  image 
when listening to music. Move sound out into the front speakers 
to  improve  the  overall  front  image,  or  add  sound  to  the  center 
speaker to fix the center image.
You  can  choose  a  level  between  0  (the  center  speaker  is 
dominant) and 7 (center sound is spread out).
The factory setting is 3.
1.  Press [-EFFECT, ―C.FOCUS] to select “C-WDTH”.
2.  Press [-] or [+] to adjust the effect.
Remote control
Center Width Control “C-WDTH”
Sound field
MUSIC MOVIE
SFC
 -EFFECT
    C.FOCUS -LEVEL
 TEST
OK
VOLUME
TOP MENU
FUNCTIONS
TUNER
DIRECT TUNING
DIRECT NAVIGATOR
SUB MENU
RETURN
SUBWOOFER7 0
8
9
10
4 5 6
>=
u
qg h
SKIP
SLOW/SEARCH
STOP PAUSE PLAYt yi
- / - -
SURROUND
PL
OFF
S -EFFECT
    C.FOCUS-LEVEL
 TEST
Main unit
You can adjust the balance of the front speakers.
1.  Use the menus to select “BALANCE”.
  ➡  MENU operation on page 16.
2. 
Press [TUNE  2 / - or 
1 / +] to adjust the balance.
Balance
You can adjust the level of the bass and treble.
1.  Use the menus to select “BASS” or “TREBLE”.
  ➡  MENU operation on page 16.
2. 
Press [TUNE  2 / - or 
1 / +] to adjust the tone.
Input  signals  must  be  either  analog  or  PCM,  and  Dolby  Pro 
Logic 
ΙΙ and SFC must be off (
➡  page 15).
Main unit
Adjusting the tone
SC-HT56P_MP (RQTX0175-2P).indb   189/19/2008   12:28:58 PM 
						

							19
RQTX0175
Sleep timer
The SLEEP timer can turn the unit off after a set time.
It does not control any other components.
1.  Use the menus to select “SLEEP”.
  ➡ MENU operation on page 16.
2. 
Press [TUNE  2 / - or 
1 / +] to select the time 
(in minutes).
  The display changes as follows:
  SLEEP  OFF  ↔ 
 SLEEP  30 
↔  SLEEP  60 
↔  SLEEP  90 
↔  SLEEP 120
To check the setting
1. Press [-MENU] to enter the main menu.
2. Press [TUNE  2 / - or 
1 / +] to select “SLEEP”.
The time remaining appears.
To change the setting
Repeat the procedure from the beginning.
Other functions
Main unit
Muting
Press [MUTING]. 
To cancel
Press [MUTING] again.
Muting also cancels when you adjust the volume or switch the
unit to standby. Remote control
Dimmer
Dim the display for better viewing in a darkened room.
1.  Use the menus to select “DIMMER”.
  ➡
 MENU operation on page 16.
2. 
Press [TUNE  2 / - or 
1 / +] to select the level 
(1, 2, or 3) or OFF.
Main unit
The operation settings for the unit will be initialized to the settings made at the time of shipment.
However, any preset radio stations will not be erased.
1.  Press and hold [―SETUP] to enter the setup menu.
2.  Press [TUNE  2 / - or 
1 / +] to select “RESET” 
➡ [ENTER].
3. 
Press [TUNE  1 /+] to select “RESET YES” 
➡ [ENTER].
  To cancel, select “RESET NO”.
The RESET function
Other functions/The RESET function
SC-HT56P_MP (RQTX0175-2P).indb   199/19/2008   12:29:01 PM 
						

							20
RQTX0175
Before using a Panasonic DVD recorder or player
DVD recorder
Change the remote control code to match the remote control mode of the DVD recorder.
1. Check the remote control mode of the DVD recorder.
2.  For about one second hold down both [OK] and the numbered button ([1], [2] or [3]) (the same as the remote control mode of the  DVD recorder).
The factory setting is [1].
DVD player
Change the remote control code so you can operate a DVD player.
For about one second hold down both [OK] and [4].
This remote control can operate Panasonic DVD recorders, DVD players, and televisions.
Note that this remote control cannot operate some equipment and that it may not be able to perform some operations.
Remote control operation guide
MENU
MENU
MENU
^
^
^^
DIRECT NAVIGATOR
FUNCTIONS
TUNER
DIRECT TUNING
RETURN
STOPPAUSE
PAUSE
PAUSE
SKIP
SLOW/SEARCH
SLOW/SEARCH
Watching DVDs/TV
Switch on
Switch on the television and select input
Switch on the player and start play
Switch off
Operating the DVD recorder/DVD player
Show disc menus
Show disc menus
Show player menus S
 elect  and  enter 
menu items S
 tart  play  from  a 
selected item
Skip items 
during play
Search 
through the 
disc
C

lear  menus  or  return 
to  previous menus
Start slow-motion play
To view frame-by-frame
Stop play
Pause play
Operating the TV
Select channels directly
Adjust the volume
Remote control operation guide
SC-HT56P_MP (RQTX0175-2P).indb   209/19/2008   12:29:04 PM