Panasonic Home Network System Digital Cordless Handset Kx Hnh100w Operating Instructions

Menu list
T
o access the features, there are 2 methods.
n Scrolling through the display menus
1 MMENU N
2 Press  MC N or  MD N to select the desired main menu.  a M SELECT N
3 Press  MC N or  MD N to select the desired item from the next sub-menus.  a M SELECT N
4 Press  MC N or  MD N to select the desired setting.  a M SAVE N
n Using the direct command code
1 MMENU N a  Enter the desired code.
Example:  Press MMENU N#160 .
2 Select the desired setting.  a M SAVE N
Note:
R To exit the operation, press...

Sub-menu 1 Sub-menu 2 Settings Code
Settings
Change Disarm PIN
–#81038
At Home
– A
lert volume Handset
O
ff –6  #803
38
Hub
O
 ff –6  #
G 803
At Home
– E

ntry alert volume Handset
O
ff –6  #808
Hub
O
 ff –6  #
G 808
Away
– A

lert volume Handset
O
ff –6  #804
Hub
O
 ff –6  #
G 804
Away
– E

ntry alert volume Handset
O
ff –6  #807
Hub
O
 ff –6  #
G 807
Away
– E

xit alert volume Off
–6   #805
Talking notification 
Off #809
38Main menu:  
W 
 “Phonebook ”Operation Code
Viewing the phonebook entry....

Sub-menu 1 Sub-menu 2 Settings Code
Greeting
Record greeting* 1
–#30231
Check greeting –#30332
Pre-recorded *
 1
(Reset to pre-recorded greeting) –
#30432
New message
a
 lert *1 Outgoing call
–
O
n/Off On
<
O
ff > #338
33
Outgoing call
– N

otification to –
Outgoing call
– R

emote code Activate
<
I
nactivate >
Hub beep On
 #339
33
Settings Ring count*
 1
2-7 rings
<
4 rings>
Toll saver #211
36
Recording time *
 1
1 min

Greeting only *2#305
36
Remote code *
 1
 #30634
Screen call 
Off #310
35
Answering...

Main menu:   “
Initial setting ”Sub-menu 1 Sub-menu 2 Settings Code
Ringer setting
Ringer volume Off –
6 #160–
Ringer tone *
 3, *4
 #161–
Silent mode
– O

n/Off On
<
O
ff > #238
26
Silent mode
– S

tart/End <
11:00 PM/06:00 AM >#237 27
Silent mode
– S

elect group –
#24127
Alarm –Once
D

aily
< Off > #720
26
Talking Caller
I
 D –

Off #162
14
Handset name ––#10428
Call block *
 1
Block a single
n
umber –
#21727
Block range of
n
 umbers –
Block unknown CID
( C

ID : Caller ID) On
 
< O
ff > #240
28
First...

Sub-menu 1 Sub-menu 2 Settings Code
Set tel line
Set dial mode* 1
Pulse
 #120
12
Set flash time *
 1, *6
900 ms

600 ms
400 ms 300 ms
250 ms
200 ms 160 ms
110 ms
100 ms 90 ms
80 ms #121
15
Set line mode *
 1, *7
A < B> #122–
Call sharing *
 1
– 
Off #194
16
Network
s
 ettings Current status
–#52629
Wi-Fi settings –#52329
IP settings 
Manual (Static) #500
29
Reset network –#73029
Registration Register handset –#13012
Deregistration *
 2
–#13112
Change
l
 anguage Display
 
Español #110
12
Voice prompt *...

*6 The flash time depends on your telephone exchange or host PBX. Contact your PBX
s upplier if necessary. The setting should stay at  “700 ms ” unless pressing  MFLASH N fails to
pick up the waiting call.
*7 Generally, the line mode setting should not be changed. This setting automatically maintains receiver volume at the proper level depending on the current telephone line condition. Set
the line mode to  “A ” if telephone line condition is not good. Alarm
A
 n alarm sounds at the set time for 3...

7
MSAVE N a  M OFF N Changing the start and end time
1
MM

ENUN#237
2 Continue from step 3, “Turning silent
mode on/off”, page 26. Selecting groups to bypass silent
m

ode
1 MMENU N#241
2 Select your desired groups by pressing
1 to  9.
R “ ” is displayed next to the selected
g

roup numbers.
R To cancel a selected group, press the
same dial key again. “ ” disappears.
3 MS

AVE N a  M OFF N Call block
T
 his feature rejects calls from unwanted
callers (Caller ID subscribers only). The
following items are...

Blocking incoming calls that
h
ave no phone number
You can reject calls when no phone number is
provided, such as private callers or out of area
calls.
1 MMENU N#240
2 Mb N: Select the desired setting.  a
M SAVE N a  M OFF N Setting the first ring for the call
b
 lock list
If you do not want the first ring from a number
on the call block list to sound, turn the first ring
setting to  “Off ”. The default setting is  “On ”.
1 MMENU N#173
2 Mb N: Select the desired setting.  a
M SAVE N a  M OFF N...

R
Make sure you have the operating
instructions included with your wireless
router handy.
R The hub cannot find your wireless router if
the wireless router does not broadcast its
SSID. If there is a “stealth mode” setting,
turn it off; if there is a “SSID broadcast”
setting, turn it on. Change the appropriate
setting before performing this procedure,
and then change it back when finished. Wi-Fi network access settings
1
MM

ENUN#523
R The hub searches for available
wireless networks and
“Searching... ”...

turn off the answering system (page 31).
F
or details, see page 36. Storing the voice mail (VM)
a
 ccess number
In order to listen to your voice mail messages,
you must dial your service provider/telephone
company’s voice mail access number. Once
you have stored your voice mail access
number, you can dial it automatically
(page 30).
1 MMENU N#331
2 Enter your access number (24 digits
max.).  a M SAVE N a  M OFF N
Note:
R When storing your voice mail access
number and your mailbox password, press
MD N...