Panasonic High Definition Hospitality Lcd Display Th 32lr11 Operating Instructions

							
3D Y/C FILTER (NTSC) 
COLOR SYSTEM 
SIGNAL 
ON 
AUTO 
3 : 2 PULLDOWN 
Panasonic AUTO (4 : 3)  OFF 
4:3
[  VIDEO  ] 
3 : 2 PULLDOWN 
OFF 
XGA MODE1024 × 768
31
3:2 PULLDOWN COLOR SYSTEM / Panasonic AUTO
Select SIGNAL from the “SET UP” menu during VIDEO (S VIDEO) input
signal mode.(“SIGNAL [VIDEO]” menu is displayed.)
SET UP for Input Signals
Press to select the “COLOR SYSTEM” or “Panasonic AUTO”.
Press to select each function.
If the image becomes unstable:
With the system set on Auto, under conditions of low level or 
noisy input signals the image may in rare cases become unstable. Should \
this occur, 
set the system to match the format of the input signal.
Press to select “3:2 PULLDOWN”.
Press to set ON/OFF.
3:2 PULLDOWN:
 When ON, the display attempts to reproduce a more natural interpretatio\
n of sources such as movie 
pictures, which are recorded at 24 frames per second.
  If the picture is not stable, turn the setting to OFF.
Notes:
When ON, this setting only affects the following signal input:
•  NTSC / PAL signal input during “VIDEO (S VIDEO)” input signal.
•  525i(480i), 625i(575i), 1125(1080)/60i signal input during “COMPONENT” input signal. Mode Function
COLOR SYSTEM
Set the color system to match the input signal. When selecting “AUTO”, the color system is automatically 
selected from NTSC/PAL/SECAM, however, M.NTSC signal is not displayed properly depending on 
the attached terminal board. To display M.NTSC signal, select “M.NTSC” in COLOR SYSTEM.
AUTO SECAM M.NTSC NTSC PA L
Panasonic AUTO
(4 : 3 ) Set to “4:3” to view 4:3 images in an unchanged format when Panaso\
nic AUTO is selected. 
If you would like to view 4:3 images in Just format, set to “JUST”\
.
Note:
Panasonic AUTO does not function when BNC Dual Video Terminal Board (TY-FB9BD) is used.
XGA MODE
This menu is displayed when the input signal is analog (Component/PC).\
 This unit supports three types of XGA signals with 
60Hz vertical frequency having different aspect ratios and sampling rates (1,024 × 768 @ 60Hz, 1,280 ×\
 768 @ 60Hz, and 
1,366 × 768 @ 60Hz). Be sure to make settings in accordance with the\
 input signal in order to achieve a more appropriate 
and attractive display.
In addition, after making this setting, be sure to make each adjustment \
(such as “AUTO SETUP”) on the “POS. /SIZE” 
menu as necessary. (see page 21)
Press to select “XGA MODE”.
Press to select “1024×768”, “1280×768” , 
“1366×768”. 
						

							ADVANCED NR[ 
VIDEO ]
MOSQUITO NRVIDEO NR
BLOCK NROFF OFF
OFF
ADVANCED NR[ 
Digital ]
MOSQUITO NRVIDEO NR
BLOCK NROFF OFF
OFF
ADVANCED NR[ 
COMPONENT ]
MOSQUITO NRVIDEO NR
BLOCK NROFF OFF
OFF
ADVANCED NR[ 
RGB ]
MOSQUITO NRVIDEO NR
BLOCK NROFF OFF
OFF
()NOISE REDUCTION
OFF 
()NOISE REDUCTION
ADVANCED
32
VIDEO NR:        Automatically reduces unwanted picture noise.
MOSQUITO NR:Reduces mosquito noise around subtitles on MPEG videos.
BLOCK NR:      Reduces block noise when playing MPEG videos.
Notes:
•  NOISE REDUCTION cannot be adjusted while a PC signal is being applied.
•  BLOCK NR cannot be adjusted while a HD signal is being applied.
NOISE REDUCTION
SET UP for Input Signals
Sets the following three NR (Noise Reduction) functions together.
VIDEO NR, MOSQUITO NR, BLOCK NR
Press to select “NOISE REDUCTION”.
Press to select “OFF”, “MIN”, “MID”, “MAX”, 
“ADVANCED”.
Sets the three NR functions separately.
Press to select “ADVANCED”.
Press to enter ADVANCED NR.
1
Press to select VIDEO NR, 
MOSQUITO NR or BLOCK NR.
Press to select “OFF”, “MIN”, “MID”, 
“MAX”.2
Advanced NR

z 
						

							SYNC
SIGNAL[ 
RGB ]
3 : 2 PULLDOWN
XGA MODEAUTO
OFF
1024 × 768
SYNC
AUTO
SYNC
ON G
SYNC
VBS
H-FREQ.
V-FREQ.kHz
Hz 63.98
60.02
SIGNAL FORMAT 1280×1024/60
33
SET UP for Input Signals
Select SIGNAL from the “SET UP” menu during RGB input signal.
SYNC
Setting RGB sync signal
Confi rm that the input is set to RGB INPUT (this setting is valid only for RGB INPUT 
signal).
AUTO:  The H and V sync or synchronized signal are automatically selected. 
If both input, it is selected the H and V sync.
ON  G:  Uses a synchronized signal on the Video G signal, which is input from 
the G connector.
VBS:  Uses a synchronized signal of Composite Sync input, which is input 
from the HD connector.
Displays the frequency and the type of the current input signal.
This display is valid only for COMPONENT/RGB/PC and Digital input signal. 
Display range:
Horizontal  15 - 110 kHz
Vertical  48 - 120 Hz
Input signal display
Press to select the “SYNC”.
Press to adjust. 
						

							Options 
Weekly Command Timer 
1/3 
 
Initial INPUT  Onscreen display On 
O f f 
Off Off
0 0Maximum VOL level Initial VOL levelOffINPUT lockOffButton lockOffRemocon User levelOffAdvanced PIP
Options 
Enable Off-timer function Normal Initial Power Mode 0 ID select Off Remote ID Off Serial ID 
2/3 
 
3/3 Options 
O f f 
Off
Off Clock Display
All Aspect
Slot1 Serial Slot Select Slot power Off
Power On Screen Delay
34
1
2
3
5Press to display the SET UP menu.
4
6
Item Adjustments
Weekly Command TimerSets Weekly Command Timer. (see page 37)
Onscreen displayOn:  Displays all the following on screen.
• Power on display
• Input signal switch display
• No signal display
• Mute and the remaining time of off-timer after 
 was pressed.
Off:  Hides all the items above from view.
Initial INPUTOff  PC  INPUT1  INPUT2  INPUT3
Adjusts the input signal when the unit is turned on.
Notes:
• Only the adjusted signal is displayed. (see page 13)
• Signal can be displayed when the Terminal board is installed.
• This menu is available only when “INPUT lock” is “Off”.
• When a dual input terminal board is attached, A or B is displayed depending on the selected input signal. 
(Ex. INPUT1A, INPUT1B) 
Initial VOL levelPress
 button to adjust the volume when the unit is turned on.
Off  On
Off: Sets normal volume.
On:  Sets your preferred volume.
Notes:
•
When “Maximum VOL level” is “On”, the volume can only be adjusted between 0 and your maximum range.• You can hear the changed volume regardless of your volume setting before opening the options menu if 
you adjust the volume when “Initial VOL level” is “On” and cursor is on the menu.
Maximum VOL levelPress
 button to adjust the maximum volume.
Off  On
Off:  Sets auto maximum volume.
On:  Sets your preferred maximum volume.
Notes:
• If the “Maximum VOL level” is set lower than the “Initial VOL level”, the “Initial VOL level” automatically 
becomes the same as the “Maximum VOL level”.
• The volume display can go up to 63 regardless of the settings.
• You can hear the changed volume regardless of your volume setting before opening the options menu if 
you adjust the volume when “Maximum VOL level” is “On” and cursor is on the menu.
Press to select “OSD LANGUAGE”.
Press and hold until the Options menu is displayed.
Press to select your preferred menu.
Press to adjust the menu.
Press to exit from Options menu.
Options Adjustments 
						

							35
Item Adjustments
INPUT lockOff   PC   INPUT1   INPUT2   INPUT3
Locks the input switch operation.
Notes:
• Only the adjusted signal is displayed (see page 13).
• Signal can be displayed when the Terminal board is installed.
• Input switch can be used when this is set to “Off”.
• In two screen display mode, if anything other than “Off” is set, the value will be fi xed as the value input in 
the single screen display mode.
• When a dual input terminal board is attached, A or B is displayed depending on the selected input signal. 
(Ex. INPUT1A, INPUT1B) 
Button lockOff  MENU&ENTER  On
Off:  All the buttons on main unit can be used.
MENU&ENTER:Locks
MENU and ENTER/■ buttons on main unit.
On:Locks all the button on main unit.
Sets Button lock with the unit buttons in the following procedure.
Off:Press
+/▲ four times
:PressINPUT four times
:Press–/▼ four times
:PressENTER/■
MENU&ENTER: Press ENTER/■ four times
:Press+/▲ four times
:PressINPUT four times
:PressENTER/■
On:Press–/▼ four times
:PressENTER/■ four times
:Press+/▲ four times
:PressENTER/■
Remocon User levelOff   User1   User2   User3 
Off:  You can use all of the buttons on the remote control.
User1:You can only use ,,,,, buttons on the remote control.
User2: You can only use 
 button on the remote control.
User3:Locks all the buttons on remote control.
Advanced PIPOff:  Sets normal two screen display mode (see page 17).
On:  Sets Advanced PIP mode (see page 18).
Notes:
• When “INPUT lock” is “On”, you cannot use all the two screen display functions.
•
, buttons are unavailable during Advanced PIP mode operation.
Off-timer functionEnable:  Enables the “Off-timer function”.
Disable:  Disables the “Off-timer function”.
Note:    When “Disable” is set, the Off-timer is cancelled.
Initial Power ModeNormal  Standby  On
Sets the power mode of the unit for when the power recovers from failure or after plugging off and in again.Normal:  Power returns in as the same state as before the power interruption.
Standby:  Power returns in standby mode. (Power Indicator : red/orange)
On:    Power returns in power On. (Power Indicator : green)
Note:
When using multiple displays, “Standby” is preferred to be set in order to reduce a power load.
ID selectSets panel ID number when panel is used in “Remote ID” or “Serial ID”.
Set value range: 0 - 100
(Standard value: 0)
Remote IDThe setting of this menu is valid only when using ID remote control.
Off:  Disables ID remote control functions. You can use normal remote control operations.
On:  Enable ID remote control functions.
Serial IDSets the panel ID Control.
Off:  Disables external control by the ID.
On:  Enables the external control by the ID.
Slot PowerOff  Auto  On
Off:  Power is not transmitted to the slot power.
Auto:  Power is transmitted to the slot power only when main power is on.
On:  Power is transmitted to the slot power when main power is on or in the standby state.
Note:  In some cases, power is transmitted to the slot power when main power is on or in the standby state 
regardless of the slot power setting.
Options Adjustments 
						

							36
Item Adjustments
Power On Screen 
DelayOff   1   2   3....   30
You can set the power-on delay time of the displays to reduce the power load, when you press POWER switch 
to turn on the multiple displays that are set together. 
Set each display’s setting individually.
Off:      The display will be turned on at the same time as POWER switch is pressed.
1 to 30 (sec.):Set the power-on delay time (second).After pressing POWER switch, the display will be powered on with time delay depending on this 
setting.
Notes:
• During this function is working, the power indicator is blinking green.
• This function also works when the power recovers from failure or after plugging off and in again the power 
cord.
  After you unplug and plug the power cord in while the unit is in standby mode and also the power is being 
supplied to a terminal board, the unit will start supplying the power to the board with time delay according 
to the setting.
  The power indicator lights up red fi rst and it turns orange when the power starts being supplied to the 
board.
Clock DisplayOff:  Not display the clock.
On:  Display the clock.
The clock is displayed at the lower left of the screen when 
 button is pressed.
10:00
Note:When “PRESENT TIME SETUP” is not set, the clock is not displayed even if “Clock Display” is “On” 
(see page 25)
All AspectSets All Aspect mode (advanced aspect setting) or default aspect mode.
With each press of 
 button, the aspect changes in the selected mode.
Off:  Default aspect mode
On: All Aspect mode
Aspect mode of each setting is as follows:
(Example: HD signal)
Off   4:3
:H-FILL
:ZOOM
:FULL
:JUST
On   4:3  (1)
:4:3 (2)
:4:3 Full
:Zoom1
:Zoom2
:Zoom3
:16:9
:14:9
:Just1
:Just2
Serial Slot 
SelectSlot1  Slot2   Slot3
Selects the slot which communicates serial.
Note: The setting of an external command can be set only from the fi xed serial terminal. (see page 11)
Normalization
When both main unit buttons and remote control are disabled due to the “Button lock”, “Remocon User level” or “Remote 
ID” adjustments, set all the values “Off” so that all the buttons are enabled again.
Press the 
–/▼ button on main unit together with  button on the remote control and hold for more than 5 seconds. The 
“SHIPPING” menu is displayed and the lock is released when it disappears.
Options Adjustments 
						

							Options 
On Weekly Command TimerOnscreen display 
1/3 
 
Weekly Command Timer 
Program1MondayOnFunction
Program3Tuesday --- Wednesday Program3Thursday --- Friday Program6Saturday Program4Sunday Program Edit 
yProgram3Thursday --- Friday Program6Saturday Program4Sunday Program Edit 
Weekly Command Timer 
8:00 
10:30 0102
1/8
--:-- 03--:-- 04--:-- 
--:-- 0512:00 069:12 PON
IMS:SL1 
--- 
--- 
--- 
---  DAM:ZOOM 
AVL:10 0708
1Program
Weekly Command Timer 
20:00 
20:30 57 
58 
8/8 
 
22:00 59 --:-- 60 --:-- 
--:-- 61 --:-- 62 --:-- AVL:00 
DAM:NORM 
POF 
--- 
--- 
---  --- 
--- 63 64 
1Program
Weekly Command Timer 
8:00 
10:30 02 01
1/8 
 
--:-- 03--:-- 04--:-- 
--:-- 0512:00 069:12 PON
IMS:SL1 
--- 
--- 
--- 
---  DAM:ZOOM 
AVL:10 0708
1Program
37
Options Adjustments
Weekly Command Timer
You can set 7-day timer programming by setting time and command.
Note:
Before setting Weekly Command Timer, set PRESENT TIME SETUP.  (see page 25)
Press to select Function.
Press to select “On”.
Note:
•  When Function is set to On, SET UP TIMER 
(see page 25) is unavailable.
1
Press to select a day.
Press to select a program number.
Note:
• You can set the program from 1 to 7.
--- indicates unset.2
Press to select Program Edit.
Press to show the Program Edit screen.
Press to select Program.
Press to change the program numbers (1-7).
4 3
Press ACTION  (  ) button
Program Edit screen
Press to select a command number.
Press to show the previous / next command 
pages (1-8) of the selected program.
Press to show the command setting screen.
5
Command (--- indicates unset)
Set time of timer (--:-- indicates unset)
Command numbersProgram number 
						

							Weekly Command Timer 
0210:30 Command No Time IMS:SL1 Command 
1Program
Weekly Command Timer 
Command 
02Command No 
IMS:SL1 10:30 Time 
1Program
1/2
SIGNAL
PC
OFF
STANDBY SAVEOFF
POWER MANAGEMENTOFF
AUTO POWER OFF
OFF
OSD LANGUAGEENGLISH (
US) COMPONENT/RGB-IN SELECT
RGB
INPUT LABEL
POWER SAVE
SET UP
SHIPPING YES 
38
This function allows you to reset the unit to the factory setting.
Shipping condition
1
2
3
4Press to display the SET UP menu.
Press to select “OSD LANGUAGE”.
Press and hold till the SHIPPING menu is displayed.
Press to select “YES”.
Press to confi rm.
[from the unit]
1  Press the MENU button till the SET UP menu is displayed.
2  Press the Volume Up “+” or Down “–” button to select “OSD LANGUAGE”.
3  Press and hold the ENTER button till the SHIPPING menu is displayed.
4  Press the Volume Up “+” or Down “–” button to select “YES”.
5  Press the ENTER button and wait for 10 sec.
Note:
Press the R button to return to SET UP menu when SHIPPING menu is displayed.
Options Adjustments
Press to select Command No.
Press to select a command number.6
Press to select Time / Command.
Press to set each item.
Time:  Set the time to execute a command program.
Pressing “ ” or “ ” button once changes “Time” 1 
minute.
          Pressing “ ” or “ ” button continuously changes “Time” by 15 minutes.
Command:Select a command to execute at the set time. This unit has 58 commands to set. (see 
page 41)
Notes:
•
Command is performed in order of execution time, regardless of the command number.
•  If a command execution time overlaps with that of other commands, these commands are 
performed in number order.
• Pressing 
, Time becomes --:-- and Command becomes ---.
7
Note:
Press
 to return to the previous screen.Command setting screen 
						

							39
Troubleshooting
Before you call for service, determine the symptoms and make a few simple checks as shown below.
Symptoms
Checks
Picture Sound
InterferenceNoisy SoundElectrical Appliances
Cars / Motorcycles
Fluorescent light
Normal PictureNo SoundVolume
(Check whether the mute function has been activated on the remote control.)
No PictureNo SoundNot plugged into AC outlet
Not switched on
PICTURE and BRIGHTNESS/Volume setting
(Check by pressing the power switch or stand-by button on the remote control.)
No PictureNormal SoundIf a signal with a non-applicable color system format, or frequency is input, only the input 
terminal indication is displayed.
No ColorNormal SoundColor controls set at minimum level. (see page 22, 23)
COLOR SYSTEM (see page 31)
No remote control operations can be performed. Check whether the batteries have discharged completely and, if they have not, whether they 
were inserted properly.
Check whether the remote control sensor is exposed to an outdoor light or a strong fl uorescent 
light.
Check whether the remote control designed specifi cally for use with the unit is being used. 
(The unit cannot be operated by any other remote control.)
A cracking sound is sometimes heard from the unit. If there is nothing wrong with the picture or sound, this is the sound of the cabinet undergoing 
very slight contractions in response to changes in the room temperature.  There are no adverse 
effects on the performance or other aspects.
The top or bottom of the picture on the screen is cut 
off when I use the zoom function.Adjust the position of the picture on the screen.
Areas at the top and bottom of the screen where 
the image is missing appear when I use the zoom 
function.When using a video software program (such as a cinema size program) with a screen wider 
than one in the 16:9 mode, blank areas separate from the images are formed at the top and 
bottom of the screen.
This LCD Display uses special image processing. Hence a slight time lag may occur between image and audio, depending on the type of input signal. 
However, this is not a malfunction.
LCD Display panel
Symptoms Check
It takes a while for the picture to appear. The unit digitally processes the various signals in order to reproduce esthetically pleasing
images. As such, it sometimes takes a few moments for the picture to appear when the power 
has been turned on, when the input has been switched or when the images for the main picture 
and sub picture on the two screens are swapped.
The  edges  of  the  images  fl icker. Due to the characteristics of the system used to drive the panel, the edges may appear to fl icker 
in the fast-moving parts of the images: This is normal and not indicative of malfunctioning.
The brightness on both sides of images in 4:3 mode 
changes.When viewing the side panels at the “BRIGHT” or “MID” setting, the brightness on both sides 
may change depending on the kind of program shown: This is normal and not indicative of 
malfunctioning.
There may be red spots, blue spots, green spots and 
black spots on the screen.This is a characteristic of liquid crystal panels and is not a problem. The liquid crystal panel 
is built with very high precision technology giving you fi ne picture details. Occasionally, a few 
non-active pixels may appear on the screen as fi xed points of red, blue, green, or black.
Please note this does not affect the performance of your LCD.
Image retention appearsImage retention may occur. If you display a still picture for an extended period, the image 
might remain on the screen. However, it will disappear after a while. This is not considered 
as malfunction. 
						

							40
List of Aspect Modes
Aspect mode
Picture
 Enlarged screenDescriptionAll Aspect: 
OnFactory setting
All Aspect: Off
16:9 FULL
The display of the pictures fi lls the screen.
In the case of SD signals, pictures with a 4:3 aspect ratio are 
enlarged horizontally, and displayed. This mode is suited to 
displaying anamorphic pictures with a 16:9 aspect ratio.
14:9 –
Letterbox pictures with a 14:9 aspect ratio are enlarged 
vertically and horizontally so that their display fi lls the 
screen vertically and is slightly smaller than the screen 
horizontally. The top and bottom edges of the pictures are 
cut off. Side panels are displayed at the left and right edges 
of the screen.
Just
JUST
Pictures with a 4:3 aspect ratio are enlarged horizontally 
so that the picture distortion is minimized. The display of 
the areas around the left and right edges of the screen is 
slightly elongated. Just1
Just2 JUST
Pictures with a 4:3 aspect ratio are enlarged horizontally 
so that the picture distortion is minimized. The left and right 
edges of the pictures are cut off. The display of the areas 
around the left and right edges of the screen is slightly 
elongated.
4:3
4:3
Pictures with a 4:3 aspect ratio are displayed with their 
original aspect ratio. Side panels are displayed at the left 
and right edges of the screen.
4:3 (1)
4:3 (2) 4:3
Pictures with a 4:3 aspect ratio are displayed with their 
original aspect ratio. The left and right edges of the pictures 
are masked by side panels.
4:3 Full H-FILL
Pictures with a 4:3 aspect ratio are enlarged horizontally so 
that their display fi lls the screen. The left and right edges of 
the pictures are cut off.
Zoom
ZOOM
Letterbox pictures with a 16:9 aspect ratio are enlarged 
vertically and horizontally so that their display fi  lls the screen. 
The top and bottom edges of the pictures are cut off.
Zoom1
Zoom2 ZOOM
Letterbox pictures with a 16:9 aspect ratio are enlarged 
vertically and horizontally so that their display fi  lls the screen. 
The top and bottom edges as well as the left and right edges 
of the pictures are cut off.
Zoom3 –
Letterbox pictures with a 2.35:1 aspect ratio are enlarged 
vertically and horizontally so that their display fi lls the screen 
vertically and is slightly larger than the screen horizontally. 
The top and bottom edges as well as the left and right edges 
of the pictures are cut off.