Panasonic Hdc Tm300 Operating Instructions

							11VQT1Z09
Features
∫Very clear high definition pictures
This unit can record detailed high definition images.
High definition images (1920 k1080)
*
ANumber of available scan lines 1080
* If the recording mode is HA/HG/HX. Standard images (720
k480)
B Number of available scan lines 480
What is AVCHD?
This is a format for recording and playing back highly detailed high definition images.
Images are recorded based on the MPEG-4 AVC/H.264 codec for compressing images and audio is 
recorded with the Dolby Digital 5.1 Creator.
≥Since the recording method is different from an ordinary DVD video etc., the data is not compatible.
∫ Compatibility with other products

With other productsAvailable functionPicture quality
Watching Video/
Pictures on your TV
(l 107 to 113) Playback with the HDMI mini cable
jPlayback using VIERA Link™ (HDAVI 
Control™) ( l112)High definition 
images
Playback with the component cable [1080i]
Playback with the component cable [480i] Standard images
Playback with the AV cable
Using a DVD burner 
(l 114 to 120) Connecting a DVD burner to copy to/play back a 
disc
jPlaying back the copied disc ( l119)High definition 
images
Standard images
What you can do with a 
PC
(l 125 to 126) Copying data to a PC and editingHigh definition 
images
Writing data to BD/DVD discs and SD cards
Converting the motion picture data to MPEG2  Standard images
Creating a DVD Video disc
Dubbing images onto 
other video devices
(l 121) Dubbing images when connecting with the AV cable Standard images
HDCSD300&HS300P-VQT1Z09_eng.book  11 ページ  ２００９年１月２１日　水曜日　午前９時５３分 
						

							12VQT1Z09
Quick Guide
∫Charging the battery
1 Connect the AC cable to the AC adaptor and 
the AC outlet.
2 Insert the battery into the AC adaptor by 
aligning the arrows.
∫Inserting the battery
Install the battery by inserting it in the direction 
shown in the figure.
A Insert the battery until it clicks and locks.
∫Inserting/removing an SD card
1) Open the LCD monitor.
≥Check that the access lamp has gone off.
2) Open the SD card cover by sliding the OPEN  lever  B.
3) Insert/remove the SD card.
≥ Face the label side  C in the direction shown in 
the illustration and press it straight in as far as 
it will go.
≥ Press the center of the SD card and then pull it 
straight out.
4) Securely close the SD card cover.
≥ Securely close it until it clicks.
∫ How to turn on the power
Turn on the power by changing the mode to  , 
 or   while pressing the lock release 
button  A.
≥
To turn off the power, change the mode to OFF.Access lamp [ACCESS]  A
≥ When this unit is accessing the SD card or 
built-in memory, the access lamp lights up.
Charging lamp 
[CHARGE] A
Lights up:
Charging
Goes off:
Charging completed
OPEN
≥ Rotate the mode dial while at the same 
time pressing in the lock release button if 
changing from OFF to another mode.
≥ Align with  B.
≥ Status indicator  C
HDC-TM300
≥Rotate the mode dial while at the same 
time pressing in the lock release button if 
changing from OFF to another mode.
≥ Align with  B.
≥ Status indicator  C
OFF
HDC-HS300
HDCSD300&HS300P-VQT1Z09_eng.book  12 ページ  ２００９年１月２１日　水曜日　午前９時５３分 
						

							13VQT1Z09
∫How to use the touch screen
You can operate by directly touching the LCD 
monitor (touch screen) with your finger.
It is easier to use the stylus pen (supplied) for 
detailed operation or if it is hard to operate with 
your fingers.
Touch and release the touch screen to select 
icon or picture.
∫Language selection
1) Press the MENU button, then touch [SETUP] 
# [LANGUAGE].
2) Touch [English].
∫ Recording motion pictures
1) Change the mode to  .
2) Open the LCD monitor or extend the 
viewfinder.
3)
Press the MENU button, then touch 
[MEDIA SELECT]  # [Built-in Memory] or 
[SD CARD].
Press the MENU button, then touch 
[MEDIA SELECT]  # [HDD] or [SD CARD].
4) Press the recording start/stop button to start  recording.
∫Recording still pictures
1) Change the mode to  .
2) Open the LCD monitor or extend the 
viewfinder.
3) Press the MENU button, then touch 
[MEDIA SELECT]  # [Built-in Memory] or 
[SD CARD].
Press the MENU button, then touch 
[MEDIA SELECT]  # [HDD] or [SD CARD].
4) Press the   button fully to take the picture.
HDCSD300&HS300P-VQT1Z09_eng.book  13 ページ  ２００９年１月２１日　水曜日　午前９時５３分 
						

							14VQT1Z09
∫Motion picture playback
1) Change the mode to  .
2) Touch the play mode select icon  A to select 
desired media to be played back.
≥ Touch [VIDEO/SD CARD] to play back the SD 
card.
Touch [VIDEO/Built-in Memory] to play back 
the built-in memory.
Touch [VIDEO/HDD] to play back the HDD.
3) Touch the scene to be played back.
4) Select the playback operation by touching  the operation icon.
1/; : Playback/Pause
6 : Rewind playback
5 : Fast forward playback
∫ : Stops the playback and shows the 
thumbnails.
∫Still picture playback
1) Change the mode to  .
2) Touch the play mode select icon  A to select 
desired media to be played back.
≥ Touch [PICTURE/SD CARD] to play back the 
SD card.
Touch [PICTURE/Built-in Memory] to play back 
the built-in memory.
Touch [PICTURE/HDD] to play back the HDD.
3) Touch the still picture to be played back.
4) Select the playback operation by touching  the operation icon.
1/;: Slide show (playback of the still pictures 
in numerical order) start/pause.
2; : Plays back the previous picture.
;1 : Plays back the next picture.
∫: Stops the playback and shows the  thumbnails.
0h00m00s 0h00m00s
0h00m00s
HDCSD300&HS300P-VQT1Z09_eng.book  14 ページ  ２００９年１月２１日　水曜日　午前９時５３分 
						

							15VQT1Z09
Preparation
Before using
1
Handling of Built-in Memory 
and HDD (Hard disk drive)
:
This unit is equipped with the built-in 32 GB memory. When using this component, pay attention to the 
following points. :
This unit is equipped with the built-in 120 GB HDD. While the HDD is capable of storing a large amount 
of data, there are a few things to look out for.  When using this component, pay attention to the following 
points.
∫ Back up data periodically.
The built-in memory is temporary storage. In order  to avoid erasing data due to static electricity, 
electromagnetic waves, breakage, and failures , back up the data to a PC or DVD disc. (l114, 125)
∫ Access lamp [ACCESS] A
≥The lamp illuminates while the SD card or built-in me mory is being accessed (initialization, recording, 
playback, deleting etc.).
≥ Do not perform the following operations when the lamp illuminates. It may damage the built-in 
memory or cause a malfunction in the unit.
jTurn the unit off
j Insert and remove the USB cable
j Expose the unit to vibrations or shock
≥ About disposing of or giving away this unit. ( l154)
Indemnity about recorded content
Panasonic does not accept any responsibility for damages directly or indirectly due to any type of 
problems that result in loss of recording or  edited content, and does not guarantee any content if 
recording or editing does not work properly. Like wise, the above also applies in a case where any 
type of repair is made to the unit (including any  other non-built-in memory/HDD related component).
Handling of built-in memory [HDC-TM300]
HDCSD300&HS300P-VQT1Z09_eng.book  15 ページ  ２００９年１月２１日　水曜日　午前９時５３分 
						

							16VQT1Z09
∫Do not expose the HDD to 
vibrations and shocks.
Due to the environment and handling conditions, 
the HDD may be subject to partial damages or 
may not be able to read, record, and play back 
data. Do not expose the unit to vibrations or 
shock, and do not turn off the power during 
recording or playback.
If the unit is used in a place with loud sounds, 
such as a club or similar venue, the recording 
may stop due to sound vibrations. Recording 
data on an SD card is recommended in these 
places.
∫Back up data periodically.
The HDD is temporary stor age. In order to avoid 
erasing data due to static electricity, 
electromagnetic waves,  breakage, and failures, 
back up the data to a PC or DVD disc. ( l11 4 ,  
125)
∫ If the HDD experiences any 
abnormality, back up data 
immediately.
Failure in the HDD may produce continuous 
noise or choppy sound during recording or 
playing back. Continuous use will cause further 
deterioration, and may eventually disable the 
HDD. If these phenomena  are observed, copy 
the data on the HDD to a PC, a DVD disc etc. 
immediately and contact  consumer support. 
(l 165, 166)
Once the HDD is out of order, data cannot be 
restored.
∫ Operation may stop in hot or cold 
environments.
The unit is disabled in or der to protect the HDD.
∫Do not use the unit in low 
atmospheric pressures.
The HDD may fail if it is used at altitudes of 
3000 m (9800 feet) or higher above sea level.
∫Transportation
When the unit is transported, turn off the power 
and be careful not to shake, drop, or cause 
impact to the unit.
∫Falling detection
[ ] is indicated on the screen when it detects a 
falling state (a weightless state). If the falling 
state is detected repeatedly, the unit may stop 
the recording or playback operation in order to 
protect the HDD.
∫HDD access lamp [ACCESS HDD] 
A
≥The lamp illuminates while the HDD is being 
accessed (initialization, recording, playback, 
deleting etc.).
≥ Do not perform the following operations when 
the lamp illuminates. It may damage the HDD 
or cause a malfunction in the unit.
jTurn the unit off
j Insert and remove the USB cable
j Expose the unit to vibrations or shock
≥ About disposing of or giving away this unit. 
(l 154)
Handling of HDD [HDC-HS300]
HDCSD300&HS300P-VQT1Z09_eng.book  16 ページ  ２００９年１月２１日　水曜日　午前９時５３分 
						

							17VQT1Z09
Preparation
Before using
2
Parts identification and 
handling
1 LCD monitor (Touch screen) (l32, 41)
≥ It can open up to 90 o.
≥ It can rotate up to 180 o A  towards the lens or 
90o  B towards the viewfinder.
2 Optical image stabilizer button  [ , O.I.S.] ( l63) 3 Inlet (cooling fan)
≥
The cooling fan rotates to prevent the internal 
temperature from rising. Take care not to cover 
the inlet when using this unit.
4 Intelligent auto button [iA] ( l47)
5 PRE-REC button [PRE-REC] ( l54)
6 Eyepiece corrector dial ( l42)
7 Battery holder ( l24)
8 DC input terminal [DC IN] ( l27)
≥ Always use the supplied AC adaptor or a 
genuine Panasonic AC adaptor (VW-AD21PP; 
optional).
9 USB terminal [ ] ( l114, 122, 133)
10 Quick menu button [Q.MENU] ( l34)
11 Sub recording start/stop button ( l46)
≥ This button functions in the same manner as 
the recording start/stop button.
12 Zoom buttons ( l61)
≥ These buttons function in the same manner as 
the zoom lever. Changing the thumbnail 
display and adjusting the volume can be done.
13 Menu button [MENU] ( l33)
[HDC-TM300]
13 45
6
2
7
8
9
10 11 12 13 14 15
19
20
21A/V
16 17 18
Due to limitations in LCD production 
technology, there may be some tiny bright or 
dark spots on the LCD monitor screen. 
However, this is not a malfunction and does 
not affect the recorded picture.
HDCSD300&HS300P-VQT1Z09_eng.book  17 ページ  ２００９年１月２１日　水曜日　午前９時５３分 
						

							18VQT1Z09
14 Delete button [ ] (l97)
15 SD card open lever [OPEN] ( l29)
16 Audio-video output terminal [A/V]  (l107, 121)
≥ Use the AV cable (only the supplied cable).
17 Component terminal [COMPONENT]  (l107)
18 HDMI mini connector [HDMI] ( l107, 112)
19 Access lamp [ACCESS] ( l15, 29)
20 Card slot ( l29)
21 SD card cover ( l29)
22 Lens cover
≥ The lens cover opens in   Motion Picture 
Recording Mode or   Still Picture Recording 
Mode. ( l30)
23 Multi manual ring ( l82)
24 Speaker
25 Manual focus button [FOCUS] ( l85)
26 Manual function button [FUNCTION] (l86)
27 Remote control sensor ( l45)
28 Recording lamp ( l36)
29 Built-in flash ( l68)
30 Lens (LEICA DICOMAR)
31 Lens hood
Rotate the lens hood counter-clockwise  A to 
remove it. In order to attach it, place into slot  B, 
and then rotate it clockwise  C.
≥ When fitting the tele conversion lens 
(VW-T4314H; optional) or the wide conversion 
lens (VW-W4307H; optional), first remove the 
lens hood.
32 AF assist lamp ( l79)
33 Mode dial ( l30)
34 Recording start/stop button ( l51)
35 Status indicator ( l30) 36 Viewfinder (
l42)
22 23
24
25
26
27
28
31
32
29 30
33 34 35 36 37
4546
38 39
MIC43
44
40
41
42
Due to limitations in LCD production 
technology, there may be some tiny bright or 
dark spots on the viewfinder screen. However, 
this is not a malfunction and does not affect 
the recorded picture.
HDCSD300&HS300P-VQT1Z09_eng.book  18 ページ  ２００９年１月２１日　水曜日　午前９時５３分 
						

							19VQT1Z09
37 Photoshot button [ ] (l55)
38 Zoom lever [W/T] (In Recording Mode)  (l61)
Thumbnail display switch/Volume lever 
[s /VOLr] (In Playback Mode) ( l88)
39 Internal microphones (5.1 channel 
support)
40 Shoe adaptor mounting part
41 Shoe adaptor cover
42 Shoe adaptor release lever  [SHOE ADAPTOR RELEASE]
The video DC light/VW-LDC103PP (optional) 
etc. can be mounted on the shoe adaptor 
(supplied).
1 Open the shoe adaptor cover.
2 Attach the shoe adaptor to this unit, and 
close the cover.
3 Attach the video DC light to this unit.
≥ When removing the shoe adaptor, slide the 
SHOE ADAPTOR RELEASE lever, and 
remove the shoe adaptor while sliding the 
lever.
43 Microphone terminal [MIC]
≥ A compatible plug-in powered microphone can 
be used as an external microphone. ≥
Audio will be stereo (2 ch) with the external 
microphone input.
≥ When the unit is connected with the AC 
adaptor, sometimes noise may be heard 
depending on the microphone type. In this 
case, please switch to the battery for the power 
supply and the noise will stop.
44 Headphone terminal [ ] ( l69)
45 Grip belt
Adjust the length of the grip belt so that it fits your 
hand.
1 Flip the belt.
2 Adjust the length.
3 Replace the belt.
46 Shoulder strap fixture
47 Battery release lever [BATT] ( l24)
48 Tripod receptacle
This is a hole for attaching the unit to the optional 
tripod. (For details on mounting the tripod, refer 
to the operating instructions for the tripod.)
A Camera base
 
 
 
47 48
HDCSD300&HS300P-VQT1Z09_eng.book  19 ページ  ２００９年１月２１日　水曜日　午前９時５３分 
						

							20VQT1Z09
1 LCD monitor (Touch screen) (l32, 41)
≥ It can open up to 90 o.
≥ It can rotate up to 180 o A  towards the lens or 
90o  B towards the viewfinder.
2 Optical image stabilizer button  [ , O.I.S.] ( l63)
3 Inlet (cooling fan)
≥ The cooling fan rotates to prevent the internal 
temperature from rising. Take care not to cover 
the inlet when using this unit.
4 Intelligent auto button [iA] ( l47) 5 PRE-REC button [PRE-REC] (
l54)
6 Eyepiece corrector dial ( l42)
7 Battery holder ( l24)
8 DC input terminal [DC IN] ( l27)
≥ Always use the supplied AC adaptor or a 
genuine Panasonic AC adaptor (VW-AD21PP; 
optional).
9 USB terminal [ ] ( l114, 122, 133)
10 Quick menu button [Q.MENU] ( l34)
11 Sub recording start/stop button ( l46)
≥ This button functions in the same manner as 
the recording start/stop button.
12 Zoom buttons ( l61)
≥ These buttons function in the same manner as 
the zoom lever. Changing the thumbnail 
display and adjusting the volume can be done.
13 Menu button [MENU] ( l33)
14 Delete button [ ] ( l97)
15 SD card open lever [OPEN] (l 29)
16 Audio-video output terminal [A/V] 
(l107, 121)
≥ Use the AV cable (only the supplied cable).
17 Component terminal [COMPONENT] 
(l107)
18 HDMI mini connector [HDMI] ( l107, 112)
19 Access lamp [ACCESS] ( l29)
20 Card slot ( l29)
21 SD card cover ( l29)
[HDC-HS300]
A/V
13 45
6
2
7
8
9
10 11 12 13 14
1920
21
16 17 18
15
Due to limitations in LCD production 
technology, there may be some tiny bright or 
dark spots on the LCD monitor screen. 
However, this is not a malfunction and does 
not affect the recorded picture.
HDCSD300&HS300P-VQT1Z09_eng.book  20 ページ  ２００９年１月２１日　水曜日　午前９時５３分