Panasonic Hdc Sd60 Operating Instructions

							21VQT2M51
Preparation
Setup
1
Power supply
∫About batteries that you can use with this unit
The battery that can be used with this unit is VW-VBK180/VW-VBK360.
≥This unit has a function to distinguish the batteries that can be used, and the 
batteries (VW-VBK180/VW-VBK360) that are compatible with this function. (The 
batteries that are not compatible with this function cannot be used.)
It has been found that counterfeit battery packs which look very similar to the genuine 
product are made available to purchase in some markets. Some of these battery packs 
are not adequately protected with internal protection to meet the requirements of 
appropriate safety standards. There is a possibility that these battery packs may lead 
to fire or explosion. Please be advised that we are not liable for any accident or failure 
occurring as a result of use of a counterfeit battery pack. To ensure that safe products 
are used we would recommend that a genuine Panasonic battery pack is used.
HDCSD60_TM60_HS60-P_PC-VQT2M51_eng.book  21 ページ  ２０１０年１月１８日　月曜日　午前１１時３３分 
						

							22VQT2M51
≥Press the power button to turn off the power. ( l28)
Install the battery by inserting it in the direction shown in the figure.
Inserting/removing the battery

Removing the batteryBe sure to hold down the power button until 
the status indicator goes off. Then remove 
the battery while supporting the unit to 
prevent it from dropping.
Move the battery release lever in the 
direction indicated by the arrow and 
remove the battery when unlocked.
0ã0â0õ0õ0æ0ó0ú
A Insert the battery until it clicks 
and locks.
CAUTION
Danger of explosion if battery is 
incorrectly replaced. Replace only with 
the same or equivalent type 
recommended by the manufacturer. 
Dispose of used batteries according to 
the manufacturer’s instructions.
HDCSD60_TM60_HS60-P_PC-VQT2M51_eng.book  22 ページ  ２０１０年１月１８日　月曜日　午前１１時３３分 
						

							23VQT2M51
Important:
≥Use the supplied AC adaptor. Do not use the AC adaptor of another device.
≥ Do not use the AC cable with any other equipment as it is designed only for this unit. 
Also, do not use the AC cable from other equipment with this unit.
≥ The battery can also be charged using a battery charger (VW-BC10PP; optional).
≥ The battery will not be charged if the power is turned on.
A DC input terminal
1Connect the AC adaptor to the DC input terminal.
2Connect the AC cable to the AC adaptor, then the AC outlet.≥The status indicator will flash red at an interv al of 2 seconds, indicating that charging has 
begun.
∫ Connecting to the AC outlet
If you turn on the unit while charging with the AC adaptor, you can use the unit with power 
supplied from the outlet.
≥If the status indicator flashes at a particularly fast or slow rate, refer to page 136.
≥ We recommend using Panasonic batteries ( l11, 24, 25, 148).
≥ If you use other batteries, we cannot guarantee the quality of this product.
≥ Do not heat or expose to flame.
≥ Do not leave the battery(ies) in an automobile exposed to direct sunlight for a long period 
of time with doors and windows closed.
Charging the battery
When this unit is purchased, the battery is not charged. Charge the battery fully 
before using this unit for the first time.

HDCSD60_TM60_HS60-P_PC-VQT2M51_eng.book  23 ページ  ２０１０年１月１８日　月曜日　午前１１時３３分 
						

							24VQT2M51
∫Charging/Recording time
≥Temperature: 25 oC (77 oF)/humidity: 60%
Charging and recording time
HDC-SD60
Battery model 
number
[Voltage/Capacity  (minimum)]Charging timeRecording modeMaximum 
continuous 
recordable timeActual 
recordable 
time
Supplied battery/
VW-VBK180 (optional)
[3.6 V/1790 mAh] 2h50minHA/HG/HX 1 h 45 min
55 min
HE 1 h 50 min
VW-VBK360 
(optional)
[3.6 V/3580 mAh] 4h50minHA
3 h 35 min
1h50min
HG 3 h 40 min
HX/HE 3h40min 1h55min
HDC-TM55/HDC-TM60
Battery model  number
[Voltage/Capacity  (minimum)]Charging timeRecording modeMaximum 
continuous 
recordable timeActual 
recordable 
time
Supplied battery/
VW-VBK180 (optional)
[3.6 V/1790 mAh] 2h50min
HA/HG/HX 1 h 45 min
55 min
HE 1 h 50 min
VW-VBK360 
(optional)
[3.6 V/3580 mAh] 4h50minHA
3 h 35 min
1h50min
HG 3 h 40 min
HX/HE 3h40min 1h55min
HDCSD60_TM60_HS60-P_PC-VQT2M51_eng.book  24 ページ  ２０１０年１月１８日　月曜日　午前１１時３３分 
						

							25VQT2M51
≥These times are approximations.
≥ The indicated charging time is for when the battery has been discharged completely. 
Charging time and recordable time vary depending on the usage conditions such as 
high/low temperature.
≥The actual recordable time refers to the recordable time when repeatedly starting/stopping 
recording, turning the unit on/off, moving the zoom lever etc.
≥ The batteries heat up after use or charging. This is not a malfunction.
HDC-HS60
Battery model 
number
[Voltage/Capacity 
(minimum)]Charging timeRecording 
destinationRecording  modeMaximum 
continuous 
recordable timeActual 
recordable  time
Supplied battery/
VW-VBK180 (optional)
[3.6 V/1790 mAh]
2h50min
HDD HA/HG/
HX/HE 1h35min 50min
SD HA/HG 1h35min
50 min
HX/HE 1h40min
VW-VBK360 
(optional)
[3.6 V/3580 mAh]4h50min
HDD HA/HG/
HX/HE 3h15min1h40min
SDHA 3h20min
1h40min
HG/HX/
HE 3h20min1h45min
Battery capacity indication≥
The display changes as the battery capacity reduces. 
####
If there is less than 3 minutes remaining, then   will become red. If the battery 
discharges, then   will flash.
≥ The remaining battery capacity is displayed when using the Panasonic battery that you 
can use for this unit. The actual time can vary depending on your actual use.
≥ When using the AC adaptor or batteries made by other companies, the remaining 
battery capacity will not be shown.
HDCSD60_TM60_HS60-P_PC-VQT2M51_eng.book  25 ページ  ２０１０年１月１８日　月曜日　午前１１時３３分 
						

							26VQT2M51
Preparation
Setup
2
Recording to a card
The unit can record still pictures or motion pictures to an SD card, built-in memory or HDD. 
To record to an SD card, read the following.
Use SD cards conforming to Class 4 or higher of the SD Speed Class Rating* for 
motion picture recording.
* The SD Speed Class Rating is the speed standard for successive writes.
≥ 4 GB or more Memory Cards that do not 
have the SDHC logo or 48 GB or more 
Memory Cards that do not have the SDXC 
logo are not based on SD Memory Card 
Specifications. ≥
When the write-protect 
switch  A on SD card is 
locked, no recording, 
deletion or editing will be 
possible on the card.
≥ Keep the Memory Card out of reach of 
children to prevent swallowing.
This unit (an SDXC compatible device) is
 compatible with SD Memory Cards, SDHC 
Memory Cards and SDXC Memory Cards.  When using an SDHC memory card/SDXC 
memory card with other equipment, check the equipment is compatible with these 
memory cards.
Cards that you can use with this unit
Card typeCapacityMotion picture recordingStill 
picture 
recording
SD 
Memory 
Card 8 MB/16 MB Cannot be used.
Can be 
used.
32 MB/64 MB/
128 MB/256 MB Cannot be guaranteed in operation.
The recording may suddenly stop during 
motion picture recording depending on 
the SD card you use. (
l128)
512MB/1GB/ 2GB
Can be used.
SDHC 
Memory 
Card 4GB/6GB/8GB/
12 GB/16 GB/
24 GB/32 GB
SDXC 
Memory  Card 48 GB/64 GB
32
HDCSD60_TM60_HS60-P_PC-VQT2M51_eng.book  26 ページ  ２０１０年１月１８日　月曜日　午前１１時３３分 
						

							27VQT2M51
Caution:Check that the access lamp has gone off.
1Open the LCD monitor.
2Open the SD card cover and 
insert (remove) the SD card 
into (from) the card slot B.
≥Face the label side  C in the direction 
shown in the illustration and press it 
straight in as far as it will go.
≥ Press the center of the SD card and then 
pull it straight out.
3Securely close the SD card cover.
≥Securely close it until it clicks.
≥Do not touch the terminals on the back of 
the SD card.
≥ Do not apply strong shocks, bend, or drop 
the SD card.
≥ Electrical noise, static electricity or the 
failure of this unit or the SD card may 
damage or erase the data stored on the 
SD card.
≥ When the card access lamp is lit, do not:
jRemove the SD card
j Turn the unit off
j Insert and remove the USB cable
j Expose the unit to vibrations or shock
Performing the above while the lamp is on 
may result in damage to data/SD card or 
this unit.
≥ Do not expose the terminals of the SD 
card to water, garbage or dust. ≥
Do not place SD cards in the following 
areas:
jIn direct sunlight.
j In very dusty or humid areas.
j Near a heater.
j Locations susceptible to significant 
difference in temperature (condensation 
can occur).
j Where static electricity or 
electromagnetic waves occur.
≥ To protect SD cards, return them to their 
cases when you are not using them.
≥ About disposing of or giving away the SD 
card. ( l137)
Inserting/removing an SD card
When using an SD card not from Panasonic,  or one previously used on other equipment, 
for the first time on this unit, format the SD card. ( l48) When the SD card is formatted, all 
of the recorded data is deleted. Once the data is deleted, it cannot be restored.
 

Access lamp [ACCESS] 
A≥When this unit is accessing the SD 
card or built-in memory, the access 
lamp lights up.
HDCSD60_TM60_HS60-P_PC-VQT2M51_eng.book  27 ページ  ２０１０年１月１８日　月曜日　午前１１時３３分 
						

							28VQT2M51
Preparation
Setup
3
Turning the unit on/off
You can turn the power on and off using the power button or by opening and closing the LCD 
monitor.
Press the power button to turn on the power.
AThe status indicator lights on.
Power is turned on when the LCD monitor is opened, and power is turned off when it is 
closed.
During normal use, opening and closing of the LCD monitor can be conveniently used 
to turn the power on/off.
∫ To turn on the power
A The status indicator lights on.
∫To turn off the power
B The status indicator goes off.
≥ The power will not turn off while recording motion pictures even if the LCD monitor is 
closed.
≥ In the following cases, opening the LCD monitor does not turn on the power. Press the 
power button to turn on the power.
jWhen the unit is  originally purchased
j When you have turned off the power using the power button
Turning the power on and off with the power button
Turning the power on and off with the LCD monitor

To turn off the powerHold down the power button until the status 
indicator goes off.

HDCSD60_TM60_HS60-P_PC-VQT2M51_eng.book  28 ページ  ２０１０年１月１８日　月曜日　午前１１時３３分 
						

							29VQT2M51
Preparation
Setup
4
Selecting a mode
Change the mode to recording or playback.
Operate the mode switch to change the mode to  ,  or .
Motion Picture Recording Mode (l34)
Still Picture Recording Mode ( l36)
Playback Mode ( l40, 78)
HDCSD60_TM60_HS60-P_PC-VQT2M51_eng.book  29 ページ  ２０１０年１月１８日　月曜日　午前１１時３３分 
						

							30VQT2M51
Preparation
Setup
5
Adjusting LCD monitor
You can operate by directly touching the 
LCD monitor (touch screen) with your finger.
It is easier to use the stylus pen (supplied) 
for detailed operation or if it is hard to 
operate with your fingers.
∫Touch
Touch and release the touch screen to select 
icon or picture.
≥Touch the center of the icon.
≥ Touching the touch screen will not operate 
while you are touching another part of the 
touch screen.
∫ About the operation icons
///:
These icons are used to switch the menu 
and thumbnail display page, for item 
selection and setting etc.
:
Touch to return to the previous screen 
such as when setting menus
≥ Do not touch on the LCD monitor with 
hard pointed tips, such as ball point pens.
≥ Perform the touch screen calibration when 
the touch is not recognized or wrong 
location is recognized. ( l49)
¬ Change the mode to   or  .
Rotate the LCD monitor towards 
the lens side.
≥The image is horizontally flipped as if you 
see a mirror image. (However the image 
recorded is the same as a normal 
recording.)
≥Only some indications will appear on the 
screen. When   appears, return the 
direction of the LCD monitor to normal 
position and check the warning/alarm 
indication. ( l125)
How to use the touch screen
Recording Yourself
HDCSD60_TM60_HS60-P_PC-VQT2M51_eng.book  30 ページ  ２０１０年１月１８日　月曜日　午前１１時３３分